WilTec 62555 User manual

Operation Manual
Hammer Drill
62555
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ insignificantly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.

© by WilTec Wildanger Technik GmbH Item 62555 Page 2
http://www.WilTec.de
http://www.aoyue.eu 08 2021-1
http://www.teichtip.de
The information contained in this document may alter at any time without previous notice. It is prohibited
to copy or spread any parts of this document in any way without prior written allowance. All rights re-
served.
The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this
operating manual, nor in the diagrams and figures shown.
Even though, the WilTec Wildanger Technik GmbH has undergone biggest possible efforts to ensure
that the operating manual is complete, faultless and up to date, mistakes cannot be entirely avoided.
If you should find a mistake or wish to make a suggestion for improvement, we look forward to hearing
from you.
Send an e-mail to:
[email protected]
or use our contact form:
https://www.wiltec.de/contacts/
The most recent version of this manual in various languages can be found in our online shop via:
https://www.wiltec.de/docsearch
Our postal address is:
WilTec Wildanger Technik GmbH
Königsbenden 12
52249 Eschweiler
Germany
Do you wish to pick goods up? Our pick-up address is:
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler
Germany
To shorten the waiting time and allow for a rapid on-site transaction, we ask you to call us previously or
placing your order via the webshop.
E-mail: [e-mail]
Tel:[phone]
Fax: [phone]
To return orders for exchange, repair or for other purposes, please use the following address. Attention!
To allow for a smooth execution of your complaint or return, it is important to contact our customer
service team before returning the goods.
Returns Department
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler
E-mail: [email protected]o
Tel:[phone]
Fax: [phone]

© by WilTec Wildanger Technik GmbH Item 62555 Page 3
http://www.WilTec.de
http://www.aoyue.eu 08 2021-1
http://www.teichtip.de
Introduction
Thank you for purchasing this quality product. To minimize the risk of injury we urge that our clients
take some basic safety precautions when using this device. Please read the operation instruc-
tions carefully and make sure you have understood its content.
Keep these operation instructions safe.
Structure and main parts
№
Name
№
Name
1
Dust protection
5
Speed regulator
2
Fixing device
6
Hammer stop switch
3
On/off switch
7
Drill stop switch
4
Handle support
Accessories
•Drill chuck 1.5–13 mm / ½–20 unf
•3 × drill bits (⌀8 mm / ⌀10 mm / ⌀12 mm) SDS Plus
•Flat chisel (25×250 mm) SDS Plus
•Sharp chisel (250 mm) SDS Plus
•Lubricating grease
•Dust protection
•2 × carbon brushes
•Box

© by WilTec Wildanger Technik GmbH Item 62555 Page 4
http://www.WilTec.de
http://www.aoyue.eu 08 2021-1
http://www.teichtip.de
Technical specifications
Voltage (V)
230
Frequency (㎐)
50
Power consumption (W)
1100
Max. rotation speed (rpm)
3000
Max. drill power in concrete/steel/wood (㎜)
32
Weight (㎏)
5.8
Vibrations (㎨)
12.8
Sound power level (dB (A))
112
Sound pressure level (dB (A))
99
Protection class
II
Safety instructions
Attention! To protect yourself from electric shocks, injuries, or fire during use of electric
devices, it is vital that you obey the safety precautions. Thoroughly read all information and
instructions in this manual before using the device.
•Check if the voltage indicated on the nameplate matches the existing mains voltage.
•If using a cable drum, unwind the entire cable. The minimum line cross section should be
1,0 mm².
•If wanting to use the electric hammer outside, make sure that your energy source is suitable for
outdoor use and that the plug is protected from rain.
•Make sure to have a firm and secure stand when using the drill free-hand and while standing
on a ladder or scaffold.
•Find covered electricity, water, or fuel conducts in walls with the help of a cable finder. Avoid
touching live parts or connections.
•Wear hearing protection. Effects of a hearing loss are not immediately noticeable.
•Always wear protection goggles and a dust mask in case of great amounts of dust being gen-
erated during your work.
•Never use the device near flammable or steaming liquids.
•Always unplug the plug before performing cleaning or maintenance work. Keep the power cord
away from oil, acids, hot surfaces, and sharp edges.
•Never overcharge the device.
•Secure workpieces correctly.
•Important! Absolutely obey all national safety prescriptions concerning installation, manipula-
tion, and maintenance.
•Chisel and drill bits might be ejected out of the machine by accident, which might lead to severe
injuries.
•Before beginning to work, always check if chisel or bit drills are correctly fixed in the chuck.
•Regularly check the chuck to find signs of wear and tear or damage.
•Never operate a hammer device before having pressed it against the workpiece (wall, ceiling,
etc.).
•After having finished you work, unplug the plug before replacing the chisel or drill bit.
•Protect yourself and others from ejected particles. Wear a hard hat and install dividers.
•To protect your fingers from contusion and abrasion, always wear working gloves.
•Vibrations might cause hand-arm-system injuries. Make sure to be exposed to vibrations the
less possible.

© by WilTec Wildanger Technik GmbH Item 62555 Page 5
http://www.WilTec.de
http://www.aoyue.eu 08 2021-1
http://www.teichtip.de
•Always place the power cord so that it is behind the device and led away from it.
•Store the device out of children’s reach.
•During work, hold the device with both hands and make sure to have a safe and stable stand.
Before using the device
•Check the spot where you will use the device. With the help of a cable finder, check if there are
covered electricity, gas, or water conducts.
•Before plugging the plug in, make sure that the voltage given on the nameplate matches the
existing mains voltage.
Mounting and changing bits (Fig. 2)
The device is equipped with an SDS Plus fixing system.
•Lubricate a bit with a light film of lubricating grease before mounting it.
•Pull back and hold the fixing sleeve (see Fig. 2).
•Push the dust-free bit all the way into the chuck and turn it. The bit is locked automatically.
•Check the lock by pulling the bit.
Removing an SDS Plus bit (Fig. 3)
Pull back and hold the fixing sleeve (A) to remove the bit.
Using the device
Switching it on and off (Fig. 1)
•Switching the device in: Push the on/off switch (3).
•Switching the device off: Shortly push the on/off switch (3) and let it got.
Fixing the handle (Fig. 4)
•For safety reasons, you may only use the hammer drill with the handles fixed.
•By turning the handle holder, you can adjust the handle so that you have a secure posture.
Untighten and turn the handle holder counter-clockwise. Then re-tighten the handle holder.
Speed regulation (Fig. 5)
Adjust the rotation speed and impact number by turning the control dial. On the dial, you will find the
indications “min.”(lowest possible speed) and “max.”(highest possible speed) as well as intermediate
values.
Dust collecting device (Abb. 7)
Place the dust collecting device over the drill before performing hammer-drill work over head.

© by WilTec Wildanger Technik GmbH Item 62555 Page 6
http://www.WilTec.de
http://www.aoyue.eu 08 2021-1
http://www.teichtip.de
Hammer stop switch and drill stop switch
№
Symbol
Meaning
001
Percussion drilling
002
Drilling
003
Hammering/chiselling
If you only want to use the device as a drill, you can switch off the hammer function. Therefore, turn the
switch (7) on top of the device to the corresponding symbol 002. To re-activate the hammer function,
the switch (7) must be re-adjusted to the symbol 001.
You may switch off the drilling function of the percussion drill as well if you only want it to hammer/chisel.
Therefore, turn the switch (6) in the handle interstice to the symbol 003.To re-activate the drilling func-
tion, the switch (6) must be re-adjusted to the symbol 001.
Please note that to perform percussion drilling, both switches must point at the corresponding sym-
bol.
Important! Only impost a low pressure while percussion drilling. Too high a pressure leads to the
motor being unnecessarily charged. Regularly check the drill bits. Re-sharpen or replace blunt drill bits.
Maintenance
•Do pull out the plug before performing any maintenance or cleaning work.
•Always keep the device tidy.
•Never use caustic detergents to clean the plastic parts of the device.
•To avoid dust from collecting, you should remove all dust from the vents with the help of pres-
surised air (max. 3 bar) after having finished your work.
•Regularly check the carbon brushes. Dirty or used carbon brushes lead to excessive spark
formation and loss of performance.

© by WilTec Wildanger Technik GmbH Item 62555 Page 7
http://www.WilTec.de
http://www.aoyue.eu 08 2021-1
http://www.teichtip.de
Exploded view and parts list

© by WilTec Wildanger Technik GmbH Item 62555 Page 8
http://www.WilTec.de
http://www.aoyue.eu 08 2021-1
http://www.teichtip.de
№
Name
№
Name
№
Name
1
Brush carrier
30
O-ring
59
Spring washer
2
Carbon brush
31
Front cover
60
Distance ring
3
Brush holder
32
Aluminium housing
61
Holder
4
Rear cover
33
⌀5 steel ball
62
Key
5
Housing
34
Wheel button
63
Centrifugal axis
6
Left handle
35
Spring
64
Gear box
7
Bushing
36
Keep ring
65
Cover
8
Capacitor
37
Outer sleeve
66
O-ring
9
Cable guard
38
Screw cap
67
O-ring
10
Flange
39
O-ring
68
Sliding needle bearing
11
Right handle
40
Washer
69
Piston rod
12
Switch
41
Bearing
70
Piston pin
13
Speed control switch
42
Distance ring
71
Piston
14
Bearing
43
Distance bushing
72
O-ring
15
Stator
44
Bearing cap
73
Cone gear
16
Deflector
45
Conic gear drive
74
Clutch
17
Armature
46
Rubber seal
75
Spring
18
Bearing
47
Holder
76
Impact body
19
Middle cover
48
Washer
77
Flat key
20
Distance ring
49
Washer
78
Cylinder
21
Lower wheel button
50
Friction sheet
79
Steel bal
22
Spring
51
Gear 2
80
O-ring
23
⌀7 steel ball
52
Spring washer
81
Square-head bolt
24
Mallet
53
Ball bolt
82
Hoop
25
O-ring
54
Holder
83
Handle support
26
O-ring
55
Sliding needle bearing
84
Auxiliary handle
27
Spin sleeve
56
Washer
85
Dust protection
28
D-shaped rubber seal
57
Small armature
86
Toolbox
29
Spring
58
Gear

© by WilTec Wildanger Technik GmbH Item 62555 Page 9
http://www.WilTec.de
http://www.aoyue.eu 08 2021-1
http://www.teichtip.de
Disposal regulations
EU guidelines regarding the disposal of scrap electric appliances (WEEE, 2012/19/EU) were imple-
mented in the law related to electrical and electronic equipment and appliances.
All WilTec electric devices that fall under the WEEE regulations are labelled with the crossed-out
wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the
domestic waste.
The company WilTec Technik GmbH has been registered in the German registry EAR under the WEEE-
registration number DE45283704.
Disposal of used electrical and electronic appliances
(intended for use in the countries of the European Un-
ion and other European countries with a separate col-
lection system for these appliances).
The logo on the article or on its packaging points out
that this article must not be treated as normal house-
hold waste but must be disposed to a recycling collec-
tion point for electronic and electrical waste equipment.
By contributing to the correct disposal of this article you
protect the environment and the health of your fellow
men. Environment and health are threatened by inap-
propriate disposal.
Material recycling helps reduce the consumption of raw materials.
Additional information on recycling this article can be provided by your local community, municipal waste
disposal facilities or the store where you purchased the article.
Address:
WilTec Wildanger Technik GmbH
Königsbenden 12 / 28
D-52249 Eschweiler
Important notice:
The reprint or reproduction, even of excerpts, and any commercial use, even in part, of this instruction
manual require the written permission of WilTec Wildanger Technik GmbH.