WilTec 62832 User manual

Operation Manual
Floor-mounted 2-bike Rack
62832
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ insignificantly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.

© by WilTec Wildanger Technik GmbH Item 62832 Page 2
http://www.WilTec.de
http://www.aoyue.eu 09 2021-1
http://www.teichtip.de
The information contained in this document may alter at any time without previous notice. It is prohibited
to copy or spread any parts of this document in any way without prior written allowance. All rights re-
served.
The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this
operating manual, nor in the diagrams and figures shown.
Even though, the WilTec Wildanger Technik GmbH has undergone biggest possible efforts to ensure
that the operating manual is complete, faultless and up to date, mistakes cannot be entirely avoided.
If you should find a mistake or wish to make a suggestion for improvement, we look forward to hearing
from you.
Send an e-mail to:
[email protected]
or use our contact form:
https://www.wiltec.de/contacts/
The most recent version of this manual in various languages can be found in our online shop via:
https://www.wiltec.de/docsearch
Our postal address is:
WilTec Wildanger Technik GmbH
Königsbenden 12
52249 Eschweiler
Germany
Do you wish to pick goods up? Our pick-up address is:
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler
Germany
To shorten the waiting time and allow for a rapid on-site transaction, we ask you to call us previously or
placing your order via the webshop.
E-mail: [e-mail]
Tel:[phone]
Fax: [phone]
To return orders for exchange, repair or for other purposes, please use the following address. Attention!
To allow for a smooth execution of your complaint or return, it is important to contact our customer
service team before returning the goods.
Returns Department
WilTec Wildanger Technik GmbH
Königsbenden 28
52249 Eschweiler
E-mail: [email protected]o
Tel:[phone]
Fax: [phone]

© by WilTec Wildanger Technik GmbH Item 62832 Page 3
http://www.WilTec.de
http://www.aoyue.eu 09 2021-1
http://www.teichtip.de
Introduction
Thank you for purchasing this quality product. To minimize the risk of injury we urge that our clients
take some basic safety precautions when using this device. Please read the operation instruc-
tions carefully and make sure you have understood its content.
Keep these operation instructions safe.
General guidelines and safety
•It is the use’s responsibility to read and follow all instructions
•Inspect the product before use to ensure that it is properly assembled and that all parts function
safely and are free from defects.
•Never modify this product in any way.
•Not all circumstances can be covered in these instructions. Please use the appliance properly
and follow general safety precautions when using this product.
Parts list
Part
Description
Quantity
Part
Description
Quantity
A
Base leg
2
E
Tire loop support
4
B
Base support leg
1
F
M6×20 screw
14
C
Connection bar
1
G
M6×65 screw
2
D
Tire loop
2
H
M8 washer
2
Tools required
•10 mm wrench
•14 mm wrench

© by WilTec Wildanger Technik GmbH Item 62832 Page 4
http://www.WilTec.de
http://www.aoyue.eu 09 2021-1
http://www.teichtip.de
Assembly instructions
When assembling the bicycle rack, tighten the bolts by hand until the entire part is fitted. When all the
parts are fitted, tighten all the bolts with wrenches.
There are two options for assembly.
•Option 1 is designed so that both bicycles are on one side.
•Option 2 is designed so that one bicycle can be mounted on either side of the stand.
Option 1
Step 1
Attach the tyre loop (D) to one of the base legs (A)
using M6×20 screws (F).
Step2
Attach the tire loop supports (E) to the other base
leg (A) using M6×20 screws (F).
Step 3
Fit the two base leg assemblies together and se-
cure with M6×20 screws (F).
Step 4
Fit the connector bar (C) between the two tire
loops (D) and secure with M6×20 bolts (F).

© by WilTec Wildanger Technik GmbH Item 62832 Page 5
http://www.WilTec.de
http://www.aoyue.eu 09 2021-1
http://www.teichtip.de
Step 5
Fit the base support bar (B) between the two base
legs (A) and secure it with M6×65 screws (G) and
washers (H). Securely tighten all bolts with
wrenches.
Option 2
Step 1
Attach one tire loop (D) and one tire loop sup-
port (E) to one of the base legs (A) using M6×20
bolts (F).
Step 2
Repeat step 1 on the other base leg.

© by WilTec Wildanger Technik GmbH Item 62832 Page 6
http://www.WilTec.de
http://www.aoyue.eu 09 2021-1
http://www.teichtip.de
Step 3
Fit the two base leg assemblies together and se-
cure with M6×20 bolts (F).
Step 4
Fit the connector (C) between the two tire
loops (D) and secure with M6×20 bolts (F).
Step 5
Fit the base support bar (B) between the two base
legs (A) and secure with M6×65 bolts (G) and
washers (H). Securely tighten all bolts with
wrenches.
Important notice:
The reprint or reproduction, even of excerpts, and any commercial use, even in part, of this instruction
manual require the written permission of WilTec Wildanger Technik GmbH.