WOERLEIN TVDA670 User manual

- 1 -
Function Features
This unit incorporates analog TV and portable DVB receiver in one system. It provides
more entertainment.
DVB receiving function
Support movable DVB signal receiving.
TV receiving function
Can be connected to the TV antenna for receiving TV signal.
Radiovision receiving function
Receiving DVB radio signal via the external antenna.
EPG function
Support EPG function.
High Resolution
Provide high-resolution image.
LCD (Liquid Crystal Display)
Designed with 7" color TFT liquid crystal display clearly shows the data.
Audio and Video Output
Audio and video output can be connected to external audio and video input device.
Audio and Video Input
External Audio, Video input can be connected to most external AV sources.
TTX Function
Designed with teletext function, provide more entertainment.

- 2 -
Unit Introduction
Main Panel
1. SOURCE button
Press this button to select signal mode: DVB, TV.
2. MENU button
Press to enter or exit the setup menu.
3. LEFT/CH- button
In the menu, press to adjust the value.
In TV or DVB mode, press to select channel.
4. RIGHT/CH + button
In the menu, press to adjust the value.
In TV or DVB mode, press to select channel.
5．
．．
．POWER button
Press to turn Power On or OFF.
6．
．．
．Remote sensor
IR receiver for remote control operation.
7．
．．
．UP button
In the menu, press to adjust the value.
8．
．．
．DOWN button
In the menu, press to adjust the value.
9．
．．
．OK button
In DVB mode, press to confirm selection in the setup menu.
10．
．．
．16:9/4:3
Press to shift screen aspect ration between 16:9 and 4:3.

- 3 -
Unit Introduction
11. Speakers
Provides high quality Audio outputs.
12. TV Antenna jack
Used to connect a analog TV antenna (not incl.) by adaptor cable (included)
13. DVB antenna jack
Used to connect to the DVB-T antenna.
14. LCD screen
7" color TFT LCD screen clearly display the data.
Left Panel
1. Headphone jack
When the headphone is plugged, the internal speakers output will turn off
automatically.
2. Volume Control knob
Used to adjust the volume of the headphone and speaker.
3. Video Output Jack
Used to connect to an external monitor for output video signal.
4. Audio Input/Output and Optical Digital Output Jack
Used for connection to an external amplifier or digital processor or external audio
source.
5. AV IN/OUT Switch
Switch to IN to input an external audio/video source.
Switch to OUT when the player is connected to an external monitor.
6. DC 9.5V Input Jack
Used to connect the AC adapter or DC adapter.
Rear Panel
When using the unit, pull the bracket on
the rear panel out, and put the unit
standing on the table.

- 4 -
Remote Control
Remote Control
1. PWR Button
Press to turn Power On or OFF.
2. INFO
Press to display the status information.
3. MENU button
In DVB mode, press to enter or exit the setup menu.
4. Direction button (▲▼◄►)
Used to select different items in the menu.
5. OK button
Press to confirm the selection in setup menu.

- 5 -
Remote Control
6. EXIT button
In the DVB mode, during setting, press to return to the previous menu.
7. 0-9 number buttons
Select numbers by pressing these buttons.
8. Channel+/- button
Press to select the channel forward or backward.
9. FAV button
In the DVB mode, press to enter the favorite list, and then use the  direction
button to select, then Press the OK button to confirm and start playback.
10. PIC button
Press to change the current picture mode among STANDRAD, MEMORY, SOFT
and LIGHT.
11. RADIO button
Press to enter or exit the DVB radio mode.
12. RETURN button
Press to return to the previous channel that you have viewed.
13. MUTE button
Press to turn on/off the speaker output.
14. EPG button
In DVB mode, press to enter the channel schedule.
15. -/-- button
In TV mode, press this button and the additional number buttons to select item
numbers which are greater than 9.
16. EDIT button
In TV mode, press to edit the channels.
17. SUB button
In the DVB mode, press to select the subtitle language.
18. AUDIO button
In DVB mode, press this button repeatedly to choose Left, Right, Mono, Stereo.
19. LANGUAGE button
In DVB mode, press to select the audio language.
20. Setup button
In the TV mode, press the button to enter the picture, TV and function setup.
In DVB mode, press to enter picture and function setup menu.
21. TTX button
In DVB mode, press to display the teletext information.
22. SOURCE button
Press this button to select signal mode: DVB, TV.
23. LCD MODE
Press to shift the aspect ratio of the screen between 16:9,4:3.

- 6 -
Preparation of Remote Control
Preparation of remote control
• refer to the drawing below, take off
the battery receptacle.
• Insert the battery with the correct
polarities facing up according to
the mark on the battery holder.
• Close the back cover.
Usage of remote control
For best results, please aim the remote
control directly at the unit’s remote
sensor. Please operate the remote
control within angles about 60 degrees
and distance about 5 meters without
obstructions between the remote control
and the unit.
• The service life of the battery is
about six months in normal use.
Please replace the battery when
the remote control is not so
sensitive.
• Please take out the battery when
the remote control is not used for a
long time, in order to avoid the
damage of the remote control
caused by the liquid leaked from it.

- 7 -
Rechargeable Battery
About Rechargeable Battery Pack
Your portable DVB receiver can be connected with a lithium polymer rechargeable
battery that attaches to the bottom of the unit. Your new battery should be fully charged
before initial use. Charging time is normally about 4 hours. A fully charged battery
delivers about 2.5-3 hours of use. If the battery will not be used for a long period of
time, first fully charge the battery prior to storage .
Working conditions and precautions of the battery
•Battery should only be used and charged when temperatures are between
32-80F.
•Never put the battery in fire or water.
•Do not expose the battery to high temperatures or store in hot, sunny places.
•Maintain well-ventilated conditions around the product, avoiding heat. Don’t
put the product on bed, sofa or anything that may block ventilation to the
product.
•Do not open the battery.
•Never charge the battery for more than 8 hours. Detach battery immediately
after charging is complete if not being used. When charging the battery
pack, the light on the battery will turn red, when the charging is complete or
the battery is being used, the light will turn green.
•Detach battery when not in use.
•When the battery is weak, about several minute later, the unit will power OFF
automatically.

- 8 -
Rechargeable Battery
Battery Pack Attaching and Placement
The unit’s power supply is the AC power adapter or the battery pack. The battery pack
also can be used as a stand.
Refer to the following steps for attaching the Battery Pack:
1. Place the unit on a soft and smooth surface with its back cover facing UP (to avoid
scratching the screen).
2. Position the Battery Pack directly toward the battery slot on the back cover of the
unit.
3. Align the pins on the battery pack with holes on the unit until you hear it click and
lock into place.
After attaching the Battery Pack, place the unit LCD screen in normal position. The
attached Battery Pack serves as a stand.
When used in a vehicle, the unit is placed into a sturdy carrying Bag/Mount. The
Bag/Mount is easy to attach to a headrest and fits on most vehicle headrest types.
This is convenient for the rear seat passengers to view the screen.

- 9 -
Rechargeable Battery
Charging the Battery Pack
The battery must be attached to the unit to charge it. Plug the Power Adapter into the
unit’s DC 9.5V IN Jack, which is located on left Side of the unit. Plug the other end of
the Power Cord into a wall Outlet.
Detaching the Battery Pack
If the unit is not going to be used for long periods of time, the Battery Pack should be
detached.
Make sure the power is turned OFF before detaching the Battery Pack. After detaching
the battery pack, take care when handling the unit.
1. Place the unit on a soft and smooth surface with its back cover up to avoid
scratching the screen.
2. Press the button located on the backside of the unit to unlock the battery pack and
while pressing the button pull the battery pack out from the unit.
NOTE: When attaching or detaching the battery pack, make sure to protect the LCD
screen.

- 10 -
System Connections
• Before plugging the power cord into an AC outlet, make sure that all other
connections have been made as described below.
• Always ensure that the unit, TV and any other electrical components are switched
OFF before connecting to the unit.
Power Supply Connection
Connect the supplied adapter to the side of the unit in the jack marked “DC 9.5V IN”.
Plug the two-prong end of the power cord to an AC100-240V outlet. If you have
difficulty inserting the plug, turn it over and reinsert it. If the unit will not be used for a
long time, disconnect the plug from the outlet.
Connecting to a TV
Use the audio/video cable to connect the audio/video output of the unit to the
audio/video input of the TV. Ensure that you observe the color coding when connecting
audio and video cables.