WOERLEIN CTV-3702 DVB-T User manual

1
14” COLOR TELEVISION WITH DVD PLAYER
Instruction Manual

2

3
Remote Control Panel
1. ATV/DTV/DVD/AV
2. Open/Close
3. Mute
4. Display
5. Picture
6. DTV/RADIO
7. Guide
8. Stop
9. Menu
10. OK
11. Right
12. Angle
13. Back/Forward
14. Setup/View
15. Repeat
16. TEXT
17. Pause
18. POWER ON/OFF
19. Number Area
20. A-B
21. 10+
22. INFO/Back Forward
23. UP/CH+
24. LEFT
25. EXIT/
26. DOWN/CH-
27. VOL-
28. VOL+
29. ZOOM
30. AUDIO

4
DIGITAL TV PART:
Main Menu
Once the installation is done, switch the receiver on and press the MENU button on the remote
control unit, the following main menu options will be displayed. All the important setting and
features of your receiver can be operated from the main menu. The main menu consists of several
sub-menus such as “Installation”, “Channel Search” and “Channel Edit”.
Using the menu ---- buttons in the center of the remote can move between the menus.
1. Press MENU to display the Main Menu.
2. Press to navigate through the menu.
3. Press OK on your selected item from the menu.
4. Press EXIT to terminate an operation.
5. Press EXIT until you to back to the Main Menu.
Note: When the receiver asks you to enter your PIN code, enter ‘0000’ by pressing the
numeric buttons.

5
1. Installation
All setting that are related to TV, Dish is within this menu. The installation menu contains several
sub menus such as “Antenna Active”, “Channel Search”, and “System Setup”.
1.1.1 Local Time
You may press ---- to setup the time you want in the receiver.
1.1.2 User Interface
OSD language: control the language as to your preference.
OSD Transparency: customize the OSD transparency.
Menu Lock Setting: use this function if you want to lock access to each of the menus. The
password for this function is 0000. Then you are able to access and set up it.

6
Change Password: for your user’s desired privacy, you can change the current password (PIN)
settings ‘0000’ to a new password for security purposes. The password is consisted of four
numbers, and you must input new password twice to ensure it correctly.
Note: Store the password in a safe place in case you forget.
1.1.3 Video
Video output: there are four video output modes:
△NTSC △PAL △SECAM
Scart screen ration: There are two video ratio:
△4:3 △16:9 (normal / windscreen)

7
1.2 Antenna active
If you select “Enable” in antenna setting submenu, the tuner can provide 5V power supply if you
use the amplifier. And you may select frequency in the list.
1.2.1 Factory Reset
After you input PIN code “0000”, you will be invited to continue the reset by pressing OK, Press
EXIT to deselect if you are unsure.
Note: this action will erase all the data you have stored in the receiver and restore it to its
‘cleared’ condition. Be sure that you want to perform this function before you proceed.

8
2. Channel Search
2.1.1 Channel Search
In this menu, you can search the channels you want, and you may setup as follows.
Move the cursor to channel scan and use the left or right key to select “Auto scan” or “Manual
scan”, and then press OK to search auto scan or manual scan.
Please wait for a little while till the search is finished

9
Please wait for a little while till the search is finished
3. Channel Edit
This menu enables you to setup the channel of DVB-T, such as move channels, make your own
favorite channels list, skip channel and delete channels from the list.
3.1 TV Channel

10
3.1.1 Skip
Press 0 in this menu, you may select the program you want to skip by pressing OK, and then a
logo will display beside the program. Press OK again to remove this logo. When you press
in no-menu state, the program will skip. You can press exit key to exit and save.
3.1.2 Lock
Press 1 in this menu and input the password, you can select the program you want to lock by
pressing OK, than a logo will display beside the program. Then press the key “EXIT”,
press “OK” to exit. If you want to unlocked this program, you can press 1 in this menu and input
the password, press OK again and remove this logo . then press the key “EXIT” , use
“ “ direction key to select “OK”, press “OK” to save unlock state. When you are watching the
locked program, you must input password.
3.1.3 Move
Press 2 in this menu, you may select the program you want to move by pressing OK, and then a
logo ---- will display beside the program. Move the cursor to the position you want and press OK,
the program move to the currently place. You can EXIT key to exit and save.
3.1.4 Delete
Press 3 in this menu, you may select the program you want to delete by pressing OK, and then a
logo ---- will display beside the program. And after you exit the menu, the program you selected
will be deleted. Press OK again to remove this logo. You can press EXIT key to exit and save.
3.1.5 Name
You can rename the current program.
Press 4 in this menu, and press OK, a keyboard is shown.
Press UP/DOWN/LEFT/RIGHT to select a letter, and the OK button to overwrite the current letter
by another letter. Press OK to confirm the changed name when you have finished. If change done,
press “SAVE”.

11
3.1.6 Sort
Press 5 in this menu, all the modes of sort are listed as follow. Press numeric key to select a sort
mode. You can press EXIT key to exit and save.
3.1.7 Fav
There are six favourite groups, press FAV button switch in these groups. You may select the
program you like by pressing OK, and then a logo ---- will display beside the program. You can
press EXIT key to exit and save.
3.2 RADIO Channel
It's the same as 2.1 TV Channel.

12
4. BASIC FUNCTIONS
While viewing TV or RADIO channels various functions can be applied using your remote
control.
1. QUALITY
To show the information of current channel be played.
2. OK
To display the channels list of TV, Radio channel directly. It’s convenient for you selecting.

13
3. AUDIO
To show the list of available audio languages and soundtrack for the channel you are watching.
You can change the audio language and soundtrack you want to hear by pressing the
UP/DOWN/LEFT/RIGHT buttons, and pressing OK to confirm.
4. VOLUME
Press LEFT/RIGHT buttons to change the volume up or down.

14
TECHNICAL FEATURES
MEEG Transport Stream (Digital)
Transport Stream: ISO/IMC 13818
System: ISO/IEC 13818-1
Video: ISO/IMC 13818-2
Audio: ISO/IMC 13818-3
Profile & Level: MP@ML
Video Input Rate: Max 15Mbit/s
Tuner Part
Input Connector: IEC 169-24 Female
With F Type
Frequency Range: 170-858MHZ
(DIGITAL)
Input Impedance: 75Ω
Signal Level: -80~-15dBm
I/O connection
Video/Audio Output: 3 Phone (AUDIO
L/R, VIDEO)
SCARTS output
Power Supply
Input Voltage: AC 110~240V
Type: SMPS
Power Consumption: Max 75W
Physical Specification
Working Temperature: +5 ℃~+40℃
Operating distance for Remote Control:
Min 6m
Audio/Video Decoder
Video Aspect Ratio: 4:3

15
ANALOG TV PART:
Switch On/Off
AC Power Supply
The unit is AC operated. Insert AC plug into the AC outlet. Then insert the other end into the AC
in Jack. Switch on POWER ON/OFF. The power indicator will turn green. After several seconds,
picture will be shown on screen.
Press Power key on remote control to switch the unit on or off. When power indicator lights on red,
the unit is in stand-by status. When power indicator turns on green, the unit is in TV status.
If TV is not in use for a long time, make sure to switch off TV by pressing POWER ON/OFF.
How to select the TV channels
First of all, insert Rod Antenna into the External Antenna Jack to receive TV signals, or insert
CATV cable into External Antenna Jack. Second, press Menu key located on unit or remote
control, then press CH+ or CH- to select item PRESET. Press VOL+ or VOL- key to enter
submenu of PRESET and press CH+ or CH- to select auto program and manual program to
searching TV program. While you finish channel search, to select Channel Swap in order to edit
you favorite program. Further, After the selection of submenu CH NO., press number keys on
remote control to input Channel No.. Or simply press VOL+/VOL- to select channel. Press V+ or
V- to select SKIP/OFF. When you select SKIP, the channel will be skipped. When you select OFF,
the channel will not be skipped.
VOLUME CONTROL
1. Volume Adjustment
To adjust the volume, press the VOL+ or VOL- key located on remote control or unit.
Press V+ key to increase the volume. Green bar will be moved to right on screen.
Press V- key to decrease the volume. Green bar will be moved to left on screen.
Note: If snow spots and blue background appear on screen because signal cannot be received,
the unit will enter auto-mute mode. Under this mode, VOL+/VOL- keys are not working.
2. Mute
Under TV and AV mode, press the Mute key on the remote control to enter mute mode. Red
MUTE will be displayed on screen. Press Mute key again or press VOL+/VOL- to exit mute mode.
The volume will be recovered to the previous level.

16
Menu Control
Press the Menu key located on remote control and unit. Menu will be displayed on screen.
PICTURE →SYSTEM →TIMER →PRESET →EXTRA
↑↓
If there is an arrow, it means there is a submenu. Press CH+ or CH- key located on remote control
and unit to select menu. Press VOL+ or VOL- key on remote and unit to enter the submenu.
Pressing VOL+ or VOL- brokenly or continuously will change the settings. To exit setting, press
Menu key until menu disappears on the screen. Note: If the unit does not exit the menu setting
completely, all keys will not function except Power key.
Adjust TV Picture
1.Press Menu key on unit or remote control. Menu will be displayed on screen. Press VOL+ or
VOL- to enter PICTURE submenu. Then press CH+ or CH- key to select submenu.
CONTRAST→BRIGHT→COLOR→TINT→SHARPNESS
When you select one of the above submenu, press V+ or V- key to change its setting. Pressing V+
will increase the setting and green bar will move to right. Pressing VOL- will decrease the setting
and green bar will move to left.
Switch of TV System
Press CH+ or CH- key to select SYSTEM in menu. Press V+ or V- to enter the submenu. Then
press CH+ or CH- key to select COLOR SYSTEM and SOUND SYSTEM. Note: When TV is in
AV mode, only COLOR SYSTEM is applicable. Pressing COL SYS key and SOUND SYS key
located on remote control will directly enter COLOR SYSTEM and SOUND SYSTEM setting
menu.
1. Press CH+ or CH- to select submenu COLOR SYSTEM. Press VOL+ or VOL- key to select
the TV signal system: PAL→NTSC358→NTSC443→AUTO
. When AUTO is selected, the unit will automatically select the COLOR SYSTEM and display the
correct picture.
1. Press CH+ or CH- key to select submenu SOUND SYSTEM. Press VOL+ or VOL- key to
select TV SOUND SYSTEM: BG→DK→I→M→BG-SUB. Only when you select the correct
SOUND SYSTEM, the sound will be clear without any noise.
Timer Setting
Press CH+ or CH- key to enter TIMER setting . Press VOL+ or VOL- key to enter submenu.
Note: CLOCK must be set first. To set CLOCK, enter submenu CLOCK, press VOL+ to enter
AM/PM setting. Press number keys on remote control to input time as follows: Hour
10-digit→Hour 1-digit→Min.10-digit→Min.1-digit→Set Completion. After the set of CLOCK,
press CH+ or CH- key to select following:

17
ON TIMER →ON CH. →CLOCK
↑↓
1. Select submenu ON TIMER and press V+ to enter AM/PM setting. Press the number keys on
remote control to input time. The turn of inputting is as follows:
Hour 10-digit→Hour 1-digit→Min.10-digit→Min.1-digit→Set Completion
↑↓
Pressing V- key will cancel the setting. Pressing V+ will reset ON TIMER.
2. After selecting submenu ON CH, press the number keys to input Channel No., Pressing V+ or
V- will select Channel No. setting in turn (TV mode: Channel 2 to Channel 69; CATV mode:
Channel 1 to Channel 125).
3．When power is cut-off or the unit is turned off, the above time setting will be invalid. When
the unit is stand-by, the above setting is valid.
Extra Functions
1. Under TV or AV mode, select EXTRA in menu by pressing CH+ or CH- key. Press V+ or V-
key to enter submenu. Then press CH+ or CH- key to select as follows:
CC →LANGUAGE→BLUE BACK
↑↓
2. When submenu CC Mode is selected (Closed Caption Display), press V+/V- to select the
following: (This only available while the CCD signal is available)
TEXT2 →TEXT1 →C2 →C1 →OFF →C MUTE
↑↓
3. When submenu LANGUAGE is selected, press V+ and V- key to select:
ENGLISH/RUSSIAN/SPANISH/FRENCH/GERMAN/ITALIAN Language, which you want
to display on TV.
4. When submenu BLUE BACK ON is selected, press V+/V-key to select BLUE BACK ON or
OFF. Screen will turn blue and be muted while there is no TV or AV signal input. If there is TV or
AV signal input, unit will display picture automatically. Under TV status, when blue back is on
screen for 10 minutes, unit will enter stand-by mode .
Picture Display Mode Selection
Press Picture Key on the remote control to select SOFT, PERSONAL or DYNAMIC 3 different
picture display mode.
Sleep Timer Setting
Pressing Sleep key on remote control can preset the TV OFF time. After certain period of time,
TV will turn off automatically and enter Power Stand-by mode.
1．When you press SLEEP key once, the screen will display the remainder time from now to
sleep.
2．When you press SLEEP key, the screen will display the sleep time to be set. Every time
pressing SLEEP key will add 30 minute. But the maximum is 180 minutes. After 180 minutes, it
will back to 0 minute. See below:

18
0MIN →30MINS →60MINS →90MINS →120MINS →150MINS →180MINS
↑↓
3．When there is only 5 minutes left from now to sleep time, screen will display the remainder
time every 1-minute and keep for 5 seconds.
4．When there is only 3 seconds left from now to sleep time, the remainder time will be
displayed on screen in red until unit is turned off and enters Stand-by mode. Pressing Power key
will cancel the Sleep Timer Setting.
On Screen Display
There are two mode of DISPLAY key, one is ON, the other one is OFF. It will display present
ATV mode about following:
1．Channel No.
2．Color System
3．Sound System
4．CLOCK
5．SLEEP TIMER

19
TV Trouble Shooting
Check the following list if you find your ATV is not working properly. If you cannot fix the
problem by adopting the listed methods, please unplug the unit and ask professional to check and
fix the unit.
TV Specifications
Item Specifications
TV system
Color system：PAL/NTSC358/NTSC443/AUTO；
Sound system ：BG/DK/I/M/BG-SUB；
Video：PAL/NTSC358/NTSC443/AUTO
Channels ALL AIR OR CATU Channels
Antenna Input 75ohm standard input jack
Speaker 2W *2，8Ω, Ф66mm
Power Supply AC: 110-240V,
Trouble Check following
No picture and sound
1. Check if power plug is well inserted in the AC outlet. 2. Check if
antenna is connected well. 3. Turn off the main power and switch on the
unit after a while.
Picture is good, but sound
is poor
1. Check if antenna is connected properly. 2. Interference from nearby
electronic device.
No picture, sound is ok. ATV station has problem with signal transmission.
Spots appear on screen. Interference from automobile, motor cycle, trolley bus, high-voltage
line, neon light, etc.
Stripes appear on screen Interference from other TV set, computer, game machine, cordless
phone, mobile phone or ATV broadcasting station.
Snowflake appears on
screen
Antenna lead falls off or is damaged. Check if the direction of antenna
has been changed.
Duplicate Shadow Check if the direction of antenna has been changed by strong wind etc.
No Color or Poor Color 1. Check if antenna connection is ok. 2. Interference from TV station or
other local device.
Remote Control is not
working
1. Check if power plug is plugged properly. 2. Check if the batteries
inside remote control run out of power.
No sound from Rear
Audio L/R-Out Jack Press the V+ key on the Remote Control, or key on the unit.

20
DVD player
Press TV/ DVD/AV key located on unit or remote control to select DTV mode.
DVD OPERATIONS:
Press the Power button on the player or the remote control, then press the “TV/DVD/AV” key to
enter DVD status until “DVD” is shown on screen. And “Read” will be appeared on the TV screen
if a disc is already loaded. If there hasn’t a disc in the DVD player, “No disc” will be displayed on
the screen. Please see more details as follows.
The DVD in this unit is compatible with DVD/VCD/CD/HD-CD/DTS-CD/MP3/WMA/JPEGD.
Note: It’s of protection screen function. When the power in DVD is open, and the state of stopping
playing is over 60S, the unit will be into protection screen function.
PLAY OPERATIONS:
1. When it plays DVD disc, the content can be chosen directly on the page of menu and title; In
the course of playing, the title can be chosen directly.
2. VCD can be chosen content directly when its disc is played in order. (in the state of playing
program and opening PBC, the program can’t be chosen directly but to press the PREV or NEXT
key.)
3. When CD/CD-G/HD-CD/DTS-CD is played, you can choose number keys to find the program
you want in the current directory.
4. When WMA/MP3/JPEG disc is played, you can choose number keys to find the program you
want in the current directory.
Note: If you play from 1 to 10 programs, press the relative number keys directly(1-10). But when
you play over 10
th
program, please press the key 10+. For example, you need the 15
th
program,
press 10+ at first, then press 5; When the number you press is over the total program number, it
won’t work.
1.1 Skip up/Skip down
Press the Skip down key, the program can skip back with one title or a new program to be played;
Press the Skip up key, the program can be skip forward with one title or a new program to be
played.
1.2 REW/F.FWD
Press the F.FWD key, the program can be played at the forward speed of one of four different rules
according to the times you press. Press “F.FWD” again, it will be recovered to play at the normal
speed. Press the REW key, the case is in verse.
1.3 Repeat
In the state of playing disc in order, press” Repeat” key can be realized to play the single program
once or repeat the whole contents once. Press the “Repeat” key again then the repeated function
can be cancelled and disc is played normally.
1.4 A-B repeat
In the course of playing, press A-B key the first time as a start, and then press those key the second
time as an end, which will cause the program set in the A-B points to play repeatedly. Press the
A-B key the third time, it will cancel the setup of repeating A-B key.
1.5 Display
Press the “Display” key, the playing title, chapter, time and other accessory information will be
displayed on the screen at the form of list.