WoodFast DP430A User manual
READ ALL INSTRUCTIONS CAREFULLY
MODEL
DP430A
FOR YOUR SAFETY:
1
2
2
3
4
5
6
6
6
7
8
This tool is equipped with an approved 3 conductor and a 3 prong grounding type plug to fit the
Do not wear loose clothing gloves neckties or jewelry (rings wrist watches) to get caught in moving
parts.Wear protective hair covering to contain long hair.Roll long sleeves above the elbow.
Cluttered areas and benches invite accidents.Floor must not be slippery due to wax or sawdust.
7.KEEP CHILDREN AWAY
-1-
proper grounding type receptacle.
3.KEEP GUARDS IN PLACE
In working order and in proper adjustment and alignment.
4.WEAR PROPER APPAREL
5.USE SAFETY GOGGLES
6.KEEP WORK AREA CLEAN
General safety instructions for Power Tools
1.KNOW YOUR POWER TOOL
Read and understand the ower's manual and labels affixed to the tool.Learn its application and
limitations as well as the specific potential hazards peculiar to this tool.
2.GROUND ALL TOOLS
Assembly===============================..
Lubrication===============================
Maintenance==============================
Wire diagram==============================
Trouble shooting============================.
Repair parts==============================..
Table of Contents
General safety instructions for Power Tools================
Main specification============================
Unpacking and checking contents====================
List of loose parts in the box and bags==================.
Getting to know your drill press=====================..
25 mm
16 mm
430 mm
MT2
0 mm
0 mm
230V/1ph/ 50W
Yes
4 5*290 mm
356*356 mm
Drill Capacity
Chuck Capacity
Sewing
Spindle Taper
Spindle Travel
Column Diameter
Motor
Rack & Pinion
Base Size
Table Size
Overall Height 1050mm
Range of spindle speeds
16 speeds
Motor Speed
1400 min-1 160 240 290 350 410 4 0 530 590 660 720 1190 1350 1510 1970 2100 3000
1.Unpacking and checking contents
Separate all the parts from packaging materials and check each item make sure all items are accounted
for before discarding any packing material.
Item Description Qty
A Table>>.>>>>>>>>>>>>>>>>. 1
B Column Support Asm>>>>>>>>>>>. 1
C Owner's Manual>>>>>>>>>>>>>> 1
D Box of Loose Parts>>>>>>>>>>>>.. 1
E Bag of Loose Parts>>>>>>>>>>>>.. *
F Base>>>>>>>>>>>>>>>>>>>. 1
G Head Asm>>>..>>>>>>>>>>>>> 1
2.Remove the protective oil that is applied to the table and column.Use any ordinary household
type grease and spot remover
3.Apply a coat of paste wax to the table and column to prevent rust.Wipe all parts thoroughly with
clean dry cloth.
Main Specification
Spindle Speeds (min-1)
Unpacking and checking contents
-2-
List of Loose Parts in the box and bags
-3-
Getting to know your drill press
- 4-
Assembly
Refer to the figure install all parts correctly,
6 Feed Handle
7 Clamp-Column Lock
Crank
-5-
- 5-
tighten the screw and bolts securelly.
1 Base
2. Column/w Support Asm
3 M10*1.5-40Screw (4)
4 Head Asm
5 Table
Frequently blow out any dust that may accumulate inside the motor.
A coat of automotive type paste was applied to the table and column will help to keep the surfaces clean.
Part No. Component/Ob ect Manufacturer PCS
Motor Motor AC250V/1PH/400W 1
SB1
SB2
SB3 Push Button-Emergency Stop 250VAC/12A 1 HY57B
SB4 Micro Switch 250VAC/16A 1 KW-7-3B
SB5 Micro Switch 250VAC/16A 1 KW7
- 6-
Magnetic Switch 250VAC/16A 1 KJD12
Lubrication
All of the BALL BEARING are packed with grease at the factory.They require no further lubrication.
Periodically lubricate the table elevation machanism,the SPLINES (grooves) in the spindle,and the
RACK (teeth of the quill),see "Getting to know your drill press."
Maintenance
Wire diagram
Trouble Shooting
TROUBLE PROBABALE CAUSE REMEDY
1.Incorrect belt tension. 1.A just tension.
2.Dry Spin le. 2.Lubricate spin le.
3.Loose spin le pulley
3.Checking tightness of retaining nut on
pulley,an tighten if necessary.
4.Loose motor pulley 4.Tighten setscrews in pulleys.
1.Incorrect spee . 1.Change spee .
2.Chips not coming out of hole. 2.Retract rill bit frequently to clear chips.
3.Dull rill bit 3.Resharpen rill bit.
4.Fee ing too slow 4.Faster the spee .
5.Not lubricate 5.Lubricate rill bit.
1.Har grain in woo or
lengths of cutting lips
an /or angles not equal
1.Resharpen rill bit correctly.
2.Bent rill bit 2.Replace rill bit.
1.No "back up material" 1.Use "back-up material"
un er workpiece.
1.Not supporte or 1.Support working or clamp it.
clampe properly.
1.Workpiece pinching rill bit 1.Support working or clamp it.
or excessive fee pressure.
2.Improper belt tension. 2.A just temsion.
1.Bent rill bit 1.Use a straight rill bit.
2.Worn spin le bearings. 2.Replace bearings.
3.Drill but not properly 3.Install rill bit properly.
installe in chuck
4.chuck not properly installe . 4.Install chuck properly.
1.Dirty,grease,or oil on the 1.Using a househol etergent clean the
tapere insi e surface of chuck tapere surface of the chuck an spin le to
or on the spin les tapere remove all irt,grease an oil.
surface.
1.Spring has improper tension. 1.A just spring tension.
-7-
Noisy Operation
Drill bit burns
Drill bit lea s off9
hole not roun
Woo splinters on
un ersi e
Workpiece turn
loose from han
Drill bit bin s in
workpiece
Excessive rill bit
runout or wobble
Quill Returns too
slow or too fast
Chuck will not stay
atache to spin le
if falls off when
trying to install it.
Repair Parts
Key
No. Description Key
No. Description
1 Screw-Hex Soc.Set 11 Support Column
M6*1. -1 12 Screw-Hex HD M1 *1.5-4
2 Collar-Rack 13 Screw-Hex Soc.Set
3 Gear-Helical M1 *1.5-12
4 Crank 14 Tube Column
6 Table 15 Rack
7 Clamp-Table 16 Clamp-Column
8 Screw-Hex HD 17 Support Table w/Indicator
M16*2 -35 18 Worm-Elevation
9 Arm-Table w/Scale 19 Pin-Gear
1 Base
FIGURE1
FIGURE1 PARTS LIST
-8-
Repair Parts
Key
No. Description
1 Nut-Lock
2 Ring-Locking
3 Washer
4 Bearing-Ball 1 mm
5 Washer-Rubber
6 Tube-Quill
Key-Chuck
8 Chuck
9 Arbor
10 Key-Drift
11 Spindle
10 Bearing-Ball 25mm
FIGURE2
FIGURE2 PARTS LIST
-9-
Repair Parts
Key
No. Description Key
No. Description
1 Ring-Retaining 10 Screw-Set M10*1.5-12
2 Bearing-Ball 25mm 11 P lley-Motor
3 Spacer-Bearing 12 Knob
4 Belt-"V"1/2*29 13 Screw-Pan HD M5*0.8-12
5 N t-P lley 14 Pivot-Ldler
6 P lley-Spindle 15 P lly-Center
7 Insert-P lley 16 Bearing-Ball 15mm
8 G ard-P lley w/Labels 17 Belt-"V"1/2*27
9 Screw-RD HD Washer 18 Washer Foam
M6*1.0-16 19 Lock Washer Ext.M6
FIGURE3
FIGURE3 PARTS LIST
-10-
Key
No. Description Key
No. Description
1 knob-Motor Adjusting 24 Retainer-Spring
2 Screw-Socket Set M1 *1.5-12 25 Spring-Torsion
3 Handle-Belt Tension 26 Cap-Spring
4 Pin-Stop 27 Nut-Hex M12*1.5-8
5 Ring-Depth Stop W/Scale 28 Head w/Pointer and Trim
6 Lock-Depth Screw 29 Socket-Bulb Asm
7 Hub 32 Tie-Wire
8 Guide Scale 33 Cord-Power w/Plug
9 Knob 34 Connector-Wire
1 Rod 35 Screw-Pan HD M6*1 *12
11 Lock-Washer-Ext M5 36 Clamp-Cord
12 Screw-Pan HD M5* .8-8 37 Support-Motor Bracket
13 Box Switch 38 Screw-Hex HD M6*1. *12
14 Screw-Pan HD M5* .8-16 39 Washer 8*16*1.6
15 Switch-Locking 4 Mount-Motor
16 Screw-Pan HD M4.2*1.4-8 41 Cord-Motor
17 Switch-Locker 42 Nut-Hex M8*1.25
18 Key-Switch 43 Motor
19 Cover-Switch Plate 44 Nut-Hex M12*1.75
2 Lead-Asm 3 45 Lockwasher 1/2
21 Screw-Set Special 1 *1.5-27 46 Support-Motor Bracket
22 Nut-Hex M1 *1.5 47 Screw-Hex HD M8*1.25-16
23 Seat-Spring 48 Lever-Adjusting
FIGURE4 PARTS LIST
Table of contents
