Woodline DOUBLE STACK METAL BASE PLATE User manual

www.woodlineshade.com Toll Free 1 – 800 – 260 – 0617
ASSEMBLY INSTRUCTIONS:
463lb/210kg DOUBLE STACK
METAL BASE PLATE
.1/3
1 X TOP PLATE 1 X BOTTOM PLATE
4 X M10 x 25
COUNTERSUNK SCREWS
(PROVIDED IN HARDWARE BAG)
(PROVIDED IN HARDWARE BAG) (PROVIDED IN HARDWARE BAG)
4 x M10 x 35
BUTTON HEAD SCREWS
4 x M10
FLAT WASHERS
0,5” / 12mm thickness 0,6” / 16mm thickness
(PROVIDED IN HARDWARE BAG)
(INSTALLED IN
BOTTOM PLATE)
9 x M10 x 25mm
ADJUSTABLE
NYLON FEET
1 x 6MM ALLEN KEY
(WITH LOCK NUT - M10)
4
5
6
1
3
2
1
3
2
7
BASE ASSEMBLY
SPIGOT ASSEMBLY
13 November 2017
For alternative base options please view our website
www.woodlineshade.com

1
2
3
2/3
RED
STICKER
*
An adjustable set (M10 X 25mm in height) has been pre-installed in the
bottom plate and has a lock nut.
After each nylon foot has been adjusted
* Place the base on level ground, use the pre-installed adjustable nylon
feet with locking nut to stabilize the base where there are any small
*
The bottom plate may be placed directly on the surface, but the surface
must be su
f
ficiently flat, or the double plate base may rock, possibly
STE
P
1:
A
Determine the desired location for mounting your cantilever or center pole umbrella.
B
Using 4 people, with 1 person at each corner of the box, lift and move the box to one side of the chosen installation location.
C
Remove the strapping material and cardboard edge channels. Open box flaps to expose the top side of the plates

&

.
D

zip lock bag (containing the hardware) are left in the box. Move the plate clear of the cardboard box an
E
Carefully set the plate down. Grip the plate on all 4 corners and lift the plate again, placing it in the desired location.
STE
P
2:
A
.
B
out as needed. When the foot is the correct height, use a 17mm open slot spanner or an adjustable
*REFER TO FIGURE (1)
*IMPOR
T
AN
T

STE
P
3:
After the bottom plate is stabilized and levelled using a spirit level, check to confirm each

A
Place the top plate

on the bottom plate

at right angles so the corners extend over the sides
of the bottom plate and the corner with the red sticker on the top plate is adjacent to the corner
with the red sticker on the bottom plate.
B
Rotate the top plate

so the two marked holes are aligned.
C
Slide to make sure all plate edges and corner screw holes are aligned.
2
RED
STICKER
BOTTOM PLATE
ADJUSTABLE NYLON FOOT
LOCK NUT:
ONCE CORRECT
FOOT HEIGHT IS
FOUND, TIGHTEN
LOCK NUT WITH
AN ADJUSTABLE
WRENCH OR 17mm
OPEN SLOT
SPANNER.
(SEE FIGURE 1)
IMPORTANT: INSTRUCTIONS FOR USING ADJUSTABLE NYLON FEET
FIGURE (1)
FIGURE (2)
*IMPORTANT: The bottom plate and top plate must be properly oriented with each other to
allow for proper alignment of all screw holes. This corner has been marked with a red sticker and must
be aligned with the countersunk hole on the top plate , which has also been marked with a red sticker.
*REFER TO FIGURE (2)
C
* IMPORTANT: BASE PLACEMENT PENDULUM UMBRELLA
If mounting near a wall, it is necessary to ensure there is sufficient room
for the umbrella to rotate. The back edge of the bottom plate should be
placed at least 5” out from any wall. This will allow for the back edge of
the structure to rotate, and prevent the structure from coming into contact
with the wall in the event of rocking caused by wind.
Please refer to the assembly instructions of the
umbrella for dimensions
www.woodlineshade.com Toll Free 1 – 800 – 260 – 0617
13 November 2017
to the desired height, tighten the lock nut against the plate.
deviations in the ground surface.
nylon feet which will protect the surface, and allow for easier cleaning
lifting of the base plate and also reduce the chance of injury.
d packaging materials.




Level and stabliize the bottom plate using the adustable nylon feet.
Note the pre-installed adjustable nylon feet have been protected during shipping with four wooden slats. Using 4 people, lift theplate up, making sure all 4 wooden slats and the
When adjusting the height of the adjustable nylon feet , loosen the lock nut and screw the foot in or
wrench to re-tighten the lock nut.
with, or below the surface.
They must be flush
adjustable nylon foot does not extend above the top side of the bottom plate.
: Make sure the adjustable nylon feet do not protrude above the top
surface of the bottom plate , or they will interfere with the top plate.
* Using the adjustable nylon feet will allow for safe handling and easier
* General requirement: when adjusting the adjustable nylon feet, the thread
of each adjustable foot must be inserted a minimum of 3/8” (10mm) into
the 0.6” (16mm) bottom plate. When levelling or stabilizing the double base
plate, do not unscrew the adjustable nylon feet out from the bottom of the
the plate more an 3/8” (10mm) from the fully installed position.
damaging the ground surface. It is recommended to use the adjustable
around and underneath the base.

CARE AND MAINTENANCE
3/3
5
1
STEP 4:
AInsert the 4 M10 x 25 screws into the countersunk corner holes in the top plate and hand tighten.
* Because it is made of galvanized steel, the double plate base will last a lifetime.
However, the plates will darken and naturally patina with age.
* Occasionally hose and wipe down the surface with a clean cloth to remove dust,
dirt, oils etc.
* The threaded holes in the double plate base have been lightly greased to protect the
threading of the stainless steel hardwear.
* In general, no maintenance is required, however, depending on the severity of the
environment, it is advisable to apply a small amount of grease to all threaded screws
every few years.
www.woodlineshade.com Toll Free 1 – 800 – 260 – 0617
POLE
6
1
STEP 5:
ARemove the spigot/stand from its box (boxed separately).
BAlign the spigot/stand with the holes in the center of the top plate.
CHand-tighten all 4 x button head screws .