Dutch & Dutch 8c User manual

Dutch & Dutch
8c.
Installation manual 8c stand
2020 V 2.0

2Installation manual 8c stand | 2020 V 2.0
Copyright
This document is protected by the Copyright Act, which covers reproduction in any form is
strictly prohibited, except with the written permission of Dutch & Dutch B.V.
The contents of this document are subject to change without notice. All technical information
in this document is for reference purposes only. The illustrations in this manual may dier
from the actual module and set-up. All drawings and diagrams are for illustrative purposes
only. All information subject to misprinting errors and technical modications.
General
This is the installation manual of the Dutch & Dutch 8c stand. Use this manual as a guide to
correctly assemble the stand and the 8c speaker on it. We recommend to store this manual
for later reference if needed.
© 2020 Dutch & Dutch B.V.
Claes de Vrieselaan 164
3021 JZ Rotterdam
The Netherlands
[phone]
www.dutchdutch.com

3Installation manual 8c stand | 2020 V 2.0
General safety
The 8c speaker has a self weight of 23kg and the plain stand (without additional sand
added) has a self weight of 12kg. You can ll the stand with sand which increases the weight of
the stand. It is recommended to install the stand with two persons to ensure a safe installation.
Always make sure that the stand with a mounted 8c speaker is installed on a at and leveled
surface. Always make sure that the mounted 8c is standing on a oor that can hold the total
weight. Do not install the stand and 8c speaker on sloped or damaged oors.
A set, the stand with mounted 8c speaker, will stand rmly on the oor. Side impacts, whether
or not caused intentionally by people, pets or other unpredictable accurentiest, can cause to
let the set fall over. Large forces will make the set fall. SInce the assembled system is heavy
this can be very dangerous. If you feel that your installation might be at risk to such an event,
please take additional measures.
During the assembly of the stand you will be holding and interlocking heavy metal parts.
Please wear building gloves to prevent risk of pinching, cutting or wounding.

4Installation manual 8c stand | 2020 V 2.0
Parts checklist
This package contains all components and
tools needed to assemble an 8c stand.
Verify that all components are there and
free from damage. When there are signs
of damage or missing parts please contact
your dealer or distributor.
1x
1x
Warning signs
This manual contains warning signs and notices for your safety. Please take notice of
these signs and act accordingly. When in doubt about how to proceed with the assembly,
contact your dealer or distributor.
General warning sign Notice sign

5Installation manual 8c stand | 2020 V 2.0
2x
4x 4x
4x
4x
4x
4x
4x
4x
4x
4x
1x4 mm 5 mm1x
2x

6Installation manual 8c stand | 2020 V 2.0
Technical Specifications
8c. speaker dimensions (HxWxD) 485 x 270 x 380 MM (19 x 10.5 x 15 IN)
8c. stand dimensions (HxWxD) 600 x 230 x 360 MM (24 x 9 x 14 IN)
8c. stand weight 12 kg
230 mm 230 mm
270 mm
600 mm
485 mm
380 mm
360 mm
Top view
Front view Side view Back view

7Installation manual 8c stand | 2020 V 2.0
Self adhesive felt
Adjustable spike
Floor protector
Step 1
Assemble the bolts, spring
washers and extension nuts to
the bottom plate. Secure them
hand-tight.
Step 2
Mount the 4 adjustable spikes
of the speaker stand.
Clean the corners of the bottom side of the
plate with one of the supplied alcohol pads
before mounting the adjustable spikes!

8Installation manual 8c stand | 2020 V 2.0
Step 4
Mount the 4 threaded rods in the 4 legs.
Step 3
Mount the 4 threaded rods through the foam.
The rods have a sharp point at the top.
Watch your hands and eyes!

9Installation manual 8c stand | 2020 V 2.0
Step 5
Mount the 4 legs of the speaker stand on
the bottom plate and push the foam into
the legs.
The legs have sharp edges.
Watch your ngers!

10 Installation manual 8c stand | 2020 V 2.0
Step 6
Optionally you can ll each leg with sand to
dampen and weighten the stand. Make sure
that the rods are centered during lling the legs.
This is an optional step,
sand is not supplied with
this package!

11Installation manual 8c stand | 2020 V 2.0
Step 7
Loosely place the top plate on the legs. Add the
bolts one by one by lining up each rod to the center
of each hole. Do not tighten the bolts at all. Once all
four bolts are on the rods, secure the top plate to the
legs. Now tighten all four bolts as much as possible
Align the rod in the
middel of the hole!
The arrow on the top plate must face
the logo plate of the bottom plate!



12 Installation manual 8c stand | 2020 V 2.0
Step 8
Rotate the stand on its side. Use the 2
allen keys to tighten the four bolts.
4 mm5 mm

13Installation manual 8c stand | 2020 V 2.0
Step 9
Mount the 4 self adhesive cable clips.
You can either choose the left or right leg.
Clean the surface of the leg with
the supplied alcohol pad befor
applying the adhesive clips!

14 Installation manual 8c stand | 2020 V 2.0
Step 10
Align the 8c with the speaker
stand before mounting.
Tighten the bolts with
the allen key till rst
point of resistance!

15Installation manual 8c stand | 2020 V 2.0
Step 11
Route the cables through the
self-adhesive cable ducts.
Make sure the speaker is
connected properly!

DUTCH & DUTCH B.V.
CLAES DE VRIESELAAN 164
3021 JZ ROTTERDAM
THE NETHERLANDS
[phone]
WWW.DUTCHDUTCH.COM
8
719326 026794