X2 X2-9891N1-PWM User manual

Installation Manual
for
ECLIPSE ADVANCED
PERFORMANCE CPU COOLER

INSTALLATION MANUAL
1 2
INSTALLATION MANUAL
1. INTRODUCTION 2. INCLUDED PARTS
A. Backplate
B.Intel Screw
C. Screw stem
D. AMD retention bars
E. Intel screw nut
F AMD screw nut
G. AMD screws
H. AMD screw pad
I. Intel screw pad
x1
x4
x4
x2
x4
x4
x4
x4
x4
The Eclipse Advanced, item number: X2-9891N1-PWM, universal CPU cooler is ideally suited for
those who require more performance and reliability than would be encountered in a generic cooler.
One of the amenities of this unique CPU cooler is the fact that its rather universal build which
enables it to be compatible with all processors such as the AMD, AM2, AM3, AM3+, FM1, FM2 and
the Intel LGA775/i3/i5/i7 and LGA2011 models. Build with _ve copper heat-pipes with a diameter of
8mm which not only boost the performance but also make an impressive appearance. Suited for a
gamer or anyone who requires overclocking to achieve faster core speeds the Eclipse Advanced by
X2 guarantees superior processor cooling. Pre-mounted with two proprietary Nano-Tech bearing
fans of 120mm boasting a lifespan of approximately seventy thousand hours alongside the
aforementioned heat-pipes to further increase cooling capacity up to 200W TDP (Thermal Design
Power). The Eclipse Advanced is packed with a universal set of mounting clip and a grease injection
tube to have you up and running in no time! Backed by our award winning service and 2 years
warranty.
J. Intel Nut
K. LGA 2011 screw stem
L. LGA2011 Nuts
M. Screwdriver
N. Thermal grease
O. Fan rubber screw (Spare)
P. Y-Splitter cable
x4
x4
x4
x1
x1
x2
x1
A B C D E
F G
P
HI J K
L M N
O

STEP 1
Remove the fan(s) from the CPU cooler before installation.
INSTALLATION MANUAL
3
3. Installation guide for AMD
STEP 2
Place the screw stem Cthrough the backplate Ainto the
designated holes, the backplate have multiple hole stand outs
which need to be checked carefully to select the right
conguration. Following fasten them with the nuts F.Then
insert the screw pad H .
STEP 4
Take the pre-assembled backplate and insert the screw stem from
the back of motherboard and through.
STEP 5
Place a small needle drop of the supplied thermal grease onto
the CPU cooler base or the CPU heat spreader and spread it out. Do not
use the whole supplied tube, this will be too much and result in a
lower cooling performance.
N
STEP 8
Install the fans onto the heatsink, connect the
Y-splitter cable to the fans and plug it into the mainboard CPU
cooler header. Please read your mainboard manual to locate the
correct CPU cooler fan header.
P
STEP 1
Remove the fan(s) from the CPU cooler before installation.
INSTALLATION MANUAL
4
3. Installation guide for Intel (except LGA 2011)
STEP 4
Place a small needle drop of the supplied thermal grease onto
the CPU cooler base or the CPU heat spreader and spread
it out. Do not use the whole supplied tube, this will be too
much and result in a lower cooling performance.
N
STEP 5
Place the heatsink onto the CPU and insert the placed screw stem
into the heatsink mounting bracket.
C
STEP 7
Install the fans onto the heatsink, connect the
Y-splitter cable to the fans and plug it into the mainboard CPU
cooler header. Please read your mainboard manual to locate the
correct CPU cooler fan header.
P
C
STEP 3
Take the pre-assembled backplate and insert the screw stem
from the back of motherboard and through.
STEP 3 (When utilizing a Socket K8 mainboard then you can skip this step)
Fasten the AMD retention bars onto the heatsink with the
supplied screws .
G
N
STEP 6
Place the heatsink onto the CPU and insert the placed screw stem into
the heatsink mounting bracket.
C
STEP 7
Fasten the supplied screws onto the stem and tighten them.
A rule of thumb is that you don’t need to tighten too fast.
On and solid secured is enough.
CE
K8
AM2/AM3
STEP 2
Place the screw stem through the backplate into the
designated Intel holes, the backplate have multiple hole stand outs
which need to be checked carefully to select the right conguration.
Following fasten them with the nuts .Then insert the screw pad .
CA
F I
STEP 6
Fasten the supplied screws onto the stem and tighten them.
A rule of thumb is that you don’t need to tighten too fast.
On and solid secured is enough.
CB

STEP 1
Before installation, please verify that your CPU platform is indeed
socket 2011. Remove the fan(s) from the CPU cooler before installation.
INSTALLATION MANUAL
5
3. Installation guide for Intel LGA 2011 only
INSTALLATION MANUAL
6
6. WARRANTY, SERVICE AND SUPPORT
WARRANTY
Under normal operation, X2 provides 24 months warranty from the date of purchase. If you have
any technical problems, please contact your local vendor or contact us, preferably by e-mail.
We will oer you full technical support to solve the issue.
Please clearly indicate the model, serial number and date of purchase.
Inproper use will void warranty.
SERVICE AND SUPPORT
If you are in need of assistance or if you have any questions, please contact us through the contact
form on our website:
www.x2products.com/contact
For urgent matters we advise you to call our headquarters, located in the Netherlands:
TEL: [phone]
STEP 3
Place a small needle drop of the supplied thermal grease onto
the CPU cooler baseor the CPU heat spreader and spread it out.
Do not use the whole supplied tube, this will be too much
and result in a lower cooling performance.
N
STEP 6
Install the fans onto the heatsink, connect the
Y-splitter cable to the fans and plug it into the mainboard CPU
cooler header. Please read your mainboard manual to locate the
correct CPU cooler fan header.
P
STEP 2
Fasten the LGA 2011 screw stem onto the mainboard.
K
STEP 4
Place the heatsink onto the CPU and insert the placed screw
stem into the heatsink mounting bracket.
K
STEP 5
Fasten the supplied Socket 2011 screws onto the stem and
tighten them. A rule of thumb is that you don’t need to tighten
too fast. On and solid secured is enough.
KL