Yalp Toro User manual

Toro installation manual
19 November 2015
Version 1.6

Contents
Yalp sports- & play equipment
T: 0031 547 289 410
E: [e-mail]
Page
3
4
5
8
10
11
12
14
16
18
20
21
22
23
24
25
1 Preparation
2 Toro goals isometric view
3 Cables
4 Field preparation
5 Artificial grass
6 Electronics: Power
7 Mounting: Surface mount
(pumpwagon)
8 Mounting: Surface mount
(forklift or crane)
9 Mounting: In ground
10 Electronics: Connections
11 Remove crane hooks
12 Technical information
13 Warranty
14 Final remarks
15 Appendix
16 Versions
This manual contains all information you need to
install this product. Make sure you
check all safety chapters and follow the
instructions to prevent dangerous situations.
If you have any remarks or improvements, please
contact us.
Have fun with the product!

EN_installation manual_Toro_v1.6 - 3 -
When placing Toro:
Make sure at least 1,7m of free space without
obstacles is available around the Toro field for
installation and safety reasons.
3G Sim card specifications
- Minimum of 250 MB/month
- 3G data subscription (no prepaid!)
- Mini sim card size (see image below)
1,7m
For installing Toro it is recommended:
• To work with two persons
Make sure a power cable for the Toro is ready on
location, with an length of at least 2 meters above
ground. The power supply must be assembled on a
separate group with a 30mA ground fault circuit
interrupter (GFCI), fused on 10A or 16A.
Ymvk ground cable, 2 cores, 2,5mm2. Maximum
cable diameter; 18mm
• Security Torx-40 bit (with hole cut-out)
• M8 tap
• M8 tap drill
• A fork spanner 13
• A cordless drill
• Socket head toolset (size 5)
• A bit holder
• A saw for the PVC pipes
Other
• Forklift truck/small crane
• Casing tubes, minimum inner
diameter; 40mm.
Length; ±13,2 m (3x)
• Electricity 230 V at master goal place.
• certified NEN1010 electrician to connect
the ground cable to the socket.
• Loctite adhesive
• Mini sim card wit a 3G connection
(250 MB/month)
1 Preparation
Mini Macro Nano
Tools list

EN_installation manual_Toro_v1.6 - 4 -
2 Toro goals isometric view
Toro master goal (1x)
Toro basic goal (3x)

EN_installation manual_Toro_v1.6 - 5 -
1. Install the 230V ground cable at the master
goal. Make sure it is powered on a separate
power group and has 2m extra length above
ground.
2. Lay the casing tubes from the basic goals to
the master goal, as shown in the illustration.
Preform the bends with an minimum radius of
1m.
3 Cables
13,66
13,06
Master goal (placed in red section)

EN_installation manual_Toro_v1.6 - 6 -
3. Make sure the casing tubes extend above the
ground, ± 5cm.
250mm
250mm
80
120
160 mm
Centerline
Ground cable
Casing tube
Casing tube
Groundwork basic goal
Groundwork master goal
200 mm
50 mm

EN_installation manual_Toro_v1.6 - 7 -
Data + powercable 18m
PCS
100-128
3
4. Lead the data+powercables through the
tubes.
2
1
Master goal
4
3

EN_installation manual_Toro_v1.6 - 8 -
4 Field preparation
The are several alternatives for the Toro floor, depending on the type of the ground
it will be placed on. Every alternative requires different placement. The following
alternatives are possible:
Option 1a: Artificial grass in ground - shockpad
Option 1b: Artificial grass in ground - sport technical layer
NB: All cables can be burrowed in the sand under the artificial grass and polyethyleen mat. Make sure
the cables are connected properly before laying the mat and grass.
NB: All cables can be burrowed in the sand under the artificial grass and sport technical layer. Make
sure the cables are connected properly before laying the mat and grass.
Artificial grass
Artificial grass
Master goal
Master goal
UTP + powercable
UTP + powercable
230V powercable
230V powercable
Polyethyleen mat
(20mm)
Compact stone
layer (100mm)
sand
sand

EN_installation manual_Toro_v1.6 - 9 -
Option 2: Floor graphics (wear-resistant pavement stickers or spray paint)
Option 3: Rubber pour in ground
NB: All cables can be burrowed in the sand under concrete tiles. Make sure the cables are connected
properly before melting the acrilyc stickers on the concrete tiles.
NB: Before pouring the rubber on top of the rubble/ tiles, make sure all cables are connected an working
correctly. All cables can be burrowed in the sand under concrete tiles/ rubble.
UTP + powercable
230V powercable
UTP + powercable
230V powercable
Melted on
acrylic stickers
Master goal
Concrete tiles
sand
sand
Rubber pour in
ground (50mm)
Master goal
Compacted
base of crushed
stone (80mm) or
concrete tiles

EN_installation manual_Toro_v1.6 - 10 -
5 Artificial grass
There are two types of foundations for an artificial turf floor. How to install an artificial
turf floor with a shockpad or sport technical layer: see the illustrations below.
Artificial turf floor - shockpad
Artificial turf floor - Sport technical layer
60x150mm endstones
4 rows of concrete tiles
300x300mm Artificial grass
Compacted base
of drainage stone
Sandbed, at least 200mm,
20 m3c sand.
20mm
Curbstones, 10x20cm. Build
20mm beneath the pavement
1200
1650
806,50
300
concrete tiles
Optional: one line with endstones
round the curbstones
Shockpad
Sandbed, at least 200mm,
20 m3c sand.
At least 200mm
20mm
Curbstones, 10x20cm. Build 20mm
beneath the pavement
Artificial grass