Yoau YPZ User manual

YPZ
7000 BTU Portable A/C
Owners Manual
Thank you for selecting our high-quality mobile air conditioner from Yoau. Before
use, please read this entire manual carefully for information regarding setting up your
portable A/C, operating it, and tips on regular maintenance. For any problems, please
contact (GCR Warranty Information).

-- 1 - -
Table of Contents
Table of Contents-----------------------------------------------------1
Important Safety Precautions--------------------------------------2
Key Features-----------------------------------------------------------3
Parts & Accessories------------------------------------------------4-5
Control Panel----------------------------------------------------------6
Remote Control--------------------------------------------------------7
Installation-------------------------------------------------------------8
Operating Methods---------------------------------------------------9
Drainage Operation-------------------------------------------------10
Maintenance----------------------------------------------------------11
Troubleshooting------------------------------------------------------12
Limited Warranty Information-----------------------------------13

-- 2 - -
Important Safety Precautions
For your and your families’ health, please read the following safety precautions
carefully before use of this air conditioner:
Requirements
* Please put the air conditioner in flat and dry places. Keep the air conditioner 50cm
away from the surrounding objects.
* Power supply of the air conditioner shall comply with the safety regulations where it
is used and ensure reliable grounding.
* After installation of the air conditioner, ensure the plug is perfect and can be inserted
into the socket securely.
* Keep air inlet and outlet unimpeded.
*The appliance shall be installed in accordance with national wiring regulations.
* The air conditioner shall be far away from gasoline, cooking stoves or other
combustibles and heat sources.
* Always keep regular and orderly placement of wires to avoid stumbling people or
pulling out the plug.
*If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
*This appliance can be used by children aged from 8 years and above and persons
with reduced physical ,sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved. Children shall not
play with the appliance.Cleaning and user maintenance shall not be made by
children without supervision
Prohibitions:
* The air conditioner is only used for households other than other places.
* Please do not install the air conditioner in washhouses or other places with water and
moist.
* Please do not turn on or off the air conditioner by inserting or pulling out the plug.
* Do not place things on the air conditioner.
* Do not put anything into air inlet and outlet.
* Do not use insecticide spray or other flammable matters in the vicinity of the air
conditioner.
* Do not splash oil or water into the air conditioner.
* Do not clean the air conditioner with water, but wipe with semi-wet soft cloth.
* Do not wipe the air conditioner with chemical solvents such as benzene, gasoline
and alcohol, etc. If the air conditioner is dirty indeed, please scrub with neutral
detergents.
Recommendations:
Recommended operation environment: temperature: 17℃-35℃, relative humidity:
20-85%RH

-- 3 - -
Key Features and Parts
Features:
＊Brand new generation condensate self-evaporation design, environment friendly
and more energy-saving.
＊L type evaporator design, enabling more compact and efficient body.
＊Ultrahigh loading quantity, greatly saving logistics cost.
＊Downsizing and compact design of the whole air conditioner.
＊Simple and convenient installation of accessories such as exhaust pipe, etc.
＊Self-diagnosis function and 24h on/off timer function.
＊Design of universal wheel with convenience for movement.
＊Quiet design, applicable to use during sleep.
＊Low noise and powerful air supply.
＊Protective function of automatic restart of compressor after 3min time delay.
Name of parts:
1. Guide strip
2. Control panel
3. Inlet grid
4. Exhaust pipe
5. Corner wheel
6. Handle
7. Strainer
8. Drainage outlet
9. Power line with plug
10. Buckle of power line
11. Exhaust outlet
Fig.1
4
3
1
2
5
Fig.1
6
3
8
11
3
10
7
9
Fig.2

-- 4 - -
Control panel
Attention: if the air conditioner is restarted immediately after shutdown in COOL or
HEAT mode, 3min protection time is necessary before automatic start.
Fig.3
Instructions of panel
1. Buttons and display
POWER: press this button to turn on or off the air conditioner.
MODE： During on or timer on pressing this button can select COOL, DEHUMIDIFY,
FAN and HEAT modes, etc. (the HEAT mode only exists in COOL/HEAT YPZ-H
model).
The corresponding indicator lamp to the selected mode is on.
UP and DOWN：If the timer on or timer off is set, pressing UP or DOWN can adjust
on/off time; in running state of COOL or HEAT mode or timer state, pressing UP or
DOWN can adjust the set temperature; and pressing UP and DOWN simultaneously
can realize conversion between ℃and ℉.
SPEED：Pressing this button can select different speeds in cycle of LOW and HIGH;
the corresponding indicator lamp to the selected speed is on.
TIMER：Press this button to enter timer setting state, and the indicator lamp is on.
DUAL 88：This pattern displays the set temperature in COOL and HEAT modes, and
displays room temperature in FAN and DEHUMIDIFIES modes; display of ℃shows
current centigrade temperature, and display of ℉shows current Fahrenheit
temperature. 88 when displayed as E2 means abnormal sense of room temperature
sensor; 88 when displayed as E3 means abnormal sense of evaporator temperature
sensor; 88 when displayed as df means the cooling system is in anti-freezing state or
defrosting state; and 88 when displayed as FL means the air conditioner is in water
full alarm state currently.
SLEEP: This indicator lamp is normally on when SLEEP state is started.
WATER FULL: In water full state this indicator lamp flickers with buzzer to prompt
drainage.

-- 5 - -
Remote control
POWER Press this button to turn on/off the air conditioner.
TIMER Press this button to set timer.
TEMPERATURE CONVERSION BUTTON Temperature is
converted from ℃to ℉.
COOL Press this button to select COOL mode.
HEAT Press this button to select HEAT mode.
DEHUMIDIFY Press this button to select DEHUMIDIFY mode.
FAN Press this button to select FAN mode.
UP/DOWN Press UP or DOWN to set temperature or adjust
timer.
HIGH Press this button to select HIGH speed.
LOW Press this button to select LOW speed.
SLEEP Press this button to set SLEEP mode. At the moment the speed of
upper and lower fans is fixed at LOW speed, in SLEEP mode temperature and
speed cannot be changed. Press this button again to cancel.
Fig.4
Single cool remote control
Cool - warm remote control
FIG.4

-- 6 - -
Operating methods
Timer setting
1. Setting of timer off
When the air conditioner is running, press this button, the timer LED lamp is on, and
meanwhile 88 Nixie tube will flicker “ ” for 5 times, at the moment, press UP and
DOWN to adjust time from 0.5h to 24h. Within 3h of timer, up/down adjustment once
only changes 0.5h, between 3~24h of timer, up/down adjustment once changes 1h.
When the set time expires, the air conditioner turns off automatically.
2. Setting timer on
When the air conditioner is in standby state, press TIMER, the timer LED lamp is on,
and meanwhile 88 Nixie tube will flicker “ ” for 5 times, at the moment press
UP/DOWN to adjust the desired time, and the method of adjustment is the same as
that during timer off. During setting of timer, the operating modes after start can be
selected, if COOL or HEAT mode is selected, the set temperature can be adjusted
simultaneously; after the set time expires, the air conditioner starts automatically and
runs in the selected operating mode.
3. Change of the set time
In the running process of timer, if you are intended to change the existing timer, you
can press TIMER once, at the moment 88 Nixie tube will flicker and display the
remaining time, during flicker pressing UP/DOWN can increase/decrease time on the
basis of the original time. If you press TIMER again during flicker, the set time will
be cancelled, namely timer quits.
Operation of operating modes
1. COOL and HEAT modes
＊In on or timer on state press MODE to select COOL or HEAT mode. At the
moment the corresponding LED on panel displays.
＊Press UP/DOWN to set appropriate temperature in a range of 18~30℃(64-86℉).
When UP or DOWN is pressed once, temperature will go up or down by 1℃or 1℉
every time.
＊Press SPEED to select appropriate speed, and LOW and HIGH speeds can be
circularly selected.
＊After selecting COOL or HEAT mode, press SLEEP on remote control (or press
UP and TIMER on operating panel simultaneously) to enter SLEEP mode, both upper
and lower fans are forcibly set at LOW speed. Setting the timing time from 0.5 to 12
hours based on your requirements, after which it will be automatically turned off. If
SLEEP is to be cancelled, press SLEEP again or conversion mode to cancel the sleep
functions.
2. DEHUMIDIFY mode
＊In on or timer on state press MODE to select DEHUMIDIFY mode. At the
moment the corresponding indicator lamp is on.
＊Temperature and speed are not adjustable.

-- 7 - -
3. FAN mode
＊In on or timer on state press MODE to select FAN mode. At the moment the
corresponding indicator lamp is on.
＊Press SPEED to select appropriate speed, and LOW and HIGH speeds can be
circularly selected.
＊Temperature is not adjustable.
Cautions:
1. When full water indication is displayed, the air conditioner will stop work,
you should drain water in time. After drainage the air conditioner will start
automatically.
2. In DEHUMIDIFY and FAN modes, you need not use exhaust pipe.
3. If your room faces the sun directly, please draw the curtains.

-- 8 - -
Installation
1. Select mounted place
Install in a flat and dry place, and 50cm must be
left around the air conditioner to enable smooth
circulation of air, as shown in Fig.5 (before
connection of exhaust pipe).
2. Assembly method of exhaust pipe
＊Connect exhaust pipe assembly with round
joint (as shown in Fig.6).
＊Fix the round end of the connected exhaust pipe
assembly at air outlet of the air conditioner as
shown in Fig.7.
＊Connect the oblate joint of the connected exhaust pipe
assembly with sealplate of window.
＊Install sealplate on the nearest window. No
Obstacles at a distance of 50cm around the
Window should be ensured to guarantee
unimpeded air exhaust.
Cautions
Exhaust pipe is 60cm~170cm long (including
adapter). We recommend using the minimum
length so as to save energy for you.
The length of exhaust pipe is especially
designed in accordance with the specification of
the air conditioner. Please do not use other exhaust
pipes of different lengths or materials, in such way
failure may be caused.
Installation of window sealplate
Design of window sealplate complies with most standard horizontal or vertical
windows, and the installation methods are shown in Fig.8 and 9.
Fig.5
Fig.8
Fig.9
Fig.6
Fig.7
Dimensions of window
sealplate:
Min. size: 90cm
Max. size: 130cm
Vertical window
Horizontal window
Dimensions of window
sealplate:
Min. size: 90cm
Max. size: 130cm

-- 9 - -
4．Illustration of installation
1) Wall mounted
2) Bow alignment
3) Incorrect bending
Fig.11
Fig.13
Fig.10
Fig.12