YOKOGAWA FIELDEYE II Series User manual

IM 85A7C03-16E
FC33E (Explosion-Proof)
FC33U (Outdoor)
FullHD IP type
Pan Tilt Zoom CCTV Camera
IM 85A7C03-16E
IM 85A7C03-16E
5th Edition
User’s
Manual
Yokogawa Electric Corporation

IM 85A7C03-16E
i
Media No.IM85A7C03-16E (CD) 5th Edition: OCT..2020 (KP)
All Rights Reserved. Copyright ©2014YokogawaElectricCorporation.
WARNING
CAUTION
SafetyPrecautions
Theprecautionshereinareintendedto ensurethesafeuseof the productand prevention
of possibleinjuryand damagetotheuser.
Theprecautions are classified into “Warning” and “Caution,” dependingon theresults
assumed to ariseif neglected, to clarify thedegree and urgency of the injury or damage.
Bothare importantfor safety. Thusbesureto observethem.
Denotesa possible hazardthatcould resultindeath or
seriousinjuryto personnel
Indique un danger potentiel pouvant entraîner la mort ou
des blessures graves au personnel.
Denotesa possible hazardthatcould resultinhumaninjury
or physicaldamage.
Indique un danger potentiel pouvant entraîner des
blessures ou des dommages physiques.
◼Pictogram examples
Shock hazard
Disassembling
prohibited
Pictogram indicatesa hazard, warning,or caution.
Inthepictogram,a specificprecautionis shown.(Thepictogram on theleft
shows“shock hazard.”)
Pictogram indicates a prohibited action.
Inor near thepictogram,a specificprecautionis shown.(Thepictogram on the
left shows“disassembling prohibited.”)

IM 85A7C03-16E
ii
WARNING
•Thisproducthas beencertifiedas an explosion-proof typedevice.
Severerestrictionsareimposedon thestructure,installationlocation,external
wiring,maintenance,repair,etc.of this device.Becarefulas dangerous
conditions mayoccur if these restrictions are infringed. Prior to handling,be sure
toread“Precautions on TIISExplosion-ProofTypeDevices” describedat the
endof thismanual.
•Infactories/facilities, thisproductshouldbehandledonlybypersonswhohave
completed appropriatetraining courses.
•When accessinga pressure-resistantand explosion-proof deviceandits
peripheralequipmentlocatedina hazardous area, preventa sparkto occur
duetomechanical contact.
•Ce produit a été certifié comme appareil de type antidéflagrant. Des
restrictions sévères sont imposées à la structure, au lieu d'installation, au
câblage externe, à la maintenance, aux réparations, etc.
•De cet appareil Faites attention car des conditions dangereuses peuvent
survenir si ces restrictions sont enfreintes.
•Avant toute manipulation, veillez à lire les Précautions relatives aux
périphériques de type antidéflagrant décrites à la fin de ce manuel
Possible explosion or fire
Fire hazard
Disassembling
prohibited
Usetheexplosion-proofCCTV camera (FC33E) inaccordancewith “Precautions
onExplosion-ProofTypeDevices” describedatthe end of this manual.
Outdoor type CCTV camera FC33U is not explosion proof. Using it in a
hazardous areawith explosivegasespresent mayresultinan explosionor fire.
Utilisez la caméra CCTV antidéflagrante (FC33E) conformément aux Précautions
relatives aux périphériques de type antidéflagrant décrites à la fin de ce manuel.
La caméra de type CCTV pour extérieur FC33U n'est pas antidéflagrante.
Donotdisassembleor modifythe product.
Ne pas démonter ni modifier le produit
Possibleelectricalshock]
Shock hazard
Disassembling
prohibited
Do not toucha connector or wiring withwet hands.
Donottouch the inside of theproductwitha piece of metal.
Donotsplashwater ontheproduct.
Ne touchez pas un connecteur ou un câblage avec les mains mouillées
Ne touchez pas l'intérieur du produit avec un morceau de métal.
Ne pas projeter d'eau sur le produit.
Donotdisassembleor modifythe product.
Ne pas démonter ni modifier le produit.

IM 85A7C03-16E
iii
Possibleinjury
Sharp edges
Moving parts
Thereareprotrusionsand sharp edges inside and outsideof theproduct.
Exercisecareto avoidbruisesor cuts.
Il y a des saillies et des arêtes vives à l'intérieur et à l'extérieur du produit.
Faites attention à éviter les ecchymoses ou les coupures.
Therearemovingpartsinsideand outsideof theproduct. Exercisecareto
prevent yourfingers from getting caught.
Il y a des pièces mobiles à l'intérieur et à l'extérieur du produit. Faites
attention à ne pas vous coincer les doigts.
Possibleturnoverorfallingoff
Slip hazard
Turnover hazard
Donotstep ontotheproduct. Youmayslip and could turnover or falloffthe product.
Ne pas marcher sur le produit. Vous pourriez glisser et renverser ou tomber du
produit.
Donotstep ontotheproduct.The product mayfallover or deform,and you
mayconsequentlyturnover and fall off the product.
Ne pas marcher sur le produit. Le produit peut tomber ou se déformer et
vous pouvez par conséquent vous retourner et tomber du produit.
Possible electrical shock or fire
Shock hazard
Donotoperatetheproductwithwethands.
Donotusedamagedcablesandwiring accessories
Ne pas utiliser le produit avec les mains mouillées
N'utilisez pas le produit avec une tension d'alimentation autre que celle spécifiée..
Prohibited
Donotuse theproduct with apower supplyvoltage other thanthat specified.
Donotusedamagedcablesandwiring accessories.
N'utilisez pas le produit avec une tension d'alimentation autre que celle spécifiée
N'utilisez pas de câbles ni d'accessoires de câblage endommagés.
Possibleinjurydueto fallingoveror offtheproduct
Prohibited
Donotplace the producton an unstablebaseor un levelplace,or thelike (Be
sureto securetheproductwithboltsof thespecifiedsize.)
Ne placez pas le produit sur une base instable, dans un endroit plat ou
similaire.( Assurez-vous de fixer le produit avec des boulons de la taille
spécifiée.)

IM 85A7C03-16E
iv
Possibledamageto devices(common)
Prohibited
Prohibited
Donotinstalltheproducton an unstablebaseor a tableof insufficientrigidity.
Doing so maydamagetheproduct due toresonance,falling off,or another cause.
N'installez pas le produit sur une base instable ou sur une table de rigidité
insuffisante. Cela pourrait endommager le produit en raison d'une résonance,
d'une chute ou d'une autre cause.
Avoid subjectingtheproductto mechanical shock.Do notputanythingon the
product.Donot stepon theproduct. Thisproductdoes isnotof awaterproof
design.Donot dip or submergeitin water. Donot testthe productusing a mega-
ohmmeter. Suchtestmaydamagethe product’s semiconductor circuits.
Évitez de soumettre le produit à des chocs mécaniques. Ne posez rien sur le
produit. Ne pas marcher sur le produit. Ce produit n’est pas étanche. Ne le
plongez pas et ne le plongez pas dans l'eau. Ne testez pas le produit avec un
mégohmmètre. Le test peut endommager les circuits semi-conducteurs du
produit
.
Revision History
February 2018 1st Edition: (Rev.00): Limited released
September 2018 2ndEdition: Published newly
October 2018 3rd Edition: Cable glands of main-body were changed
December 2018 4th Edition: Name plate change due to factory’s change
October 2020 5th Edition:CSA Certification
Trademarks:
Everytradeor companynameusedin thisdocumentisa trademarkor registered trademarkof
thecompany.

IM 85A7C03-16E
TOC-1
FC33E (Explosion-prooftype)
FC33U(Outdoortype)
Full HD IP type
Pan Tilt Zoom CCTV color Camera
IM 85A7C03-16E 5th Edition
Contents
SafetyPrecautions .......................................................................................................i
1 Introduction................................................................................................................1-1
2 HandlingPrecautions................................................................................................2-1
2.1 Transportation Precautions .......................................................................... 2-1
2.2 Storage Precautions ............................................................................................2-1
2.3 Precautions for Installation Location ...............................................................2-2
2.4 Precautions on pressure resistance and explosion prevention.....................2-2
3 Overview.....................................................................................................................3-1
3.1 MainFeatures..........................................................................................................3-1
3.2 Component Names and Functions............................................................... 3-2
3.3 Standard Specifications ................................................................................ 3-3
3.4 External dimensions...................................................................................... 3-9
4 Installation ................................................................................................................4-1
4.1 Determining the Installation Location.......................................................... 4-1
4.2 Dimensionsof and Distanceto the Object.............................................................................4-2
4.3 Installation ...........................................................................................................4-4
5 Cabling and Installing ................................................................................................5-1
5.1 Cables form FC33’s main body.............................................................................5-1
5.2 Cabling Precautions...............................................................................................5-2
5.3 Cable TerminalTreatment......................................................................................5-2
5.4 Junction Box............................................................................................................5-3
5.5 Wiring Cables into Junction Box ..........................................................................5-5
5.5.1 Standard Cable Specification .............................................................. 5-5
5.5.2 Remove the Upper-lid........................................................................... 5-6
5.5.3 Power input/output connections at JB .............................................. 5-7
5.5.4 Multiple Cable connections at JB........................................................ 5-12
5.5.5 Optical fiber connection at JB............................................................. 5-14
5.5.6 LAN connection of JB-TX..................................................................... 5-16
5.5.7 Electrical Check before Sealing .......................................................... 5-21
5.5.8 Closing the JB’s Upper-lid................................................................... 5-21
5.5.9 Connecting FG terminal....................................................................... 5-21
5.6 Cabling without JB.................................................................................................5-22
5.6.1 LAN communication............................................................................. 5-18
5.6.2 Composite cable treatment.................................................................. 5-18
5.6.3 Connecting FG terminal....................................................................... 5-20
5.7 Cable Glands of JB side(option)................................................................... 5-25
5.8 Return to Zero Position ................................................................................. 5-27
5.9 Piping requirements for CSA Explosionproof............................................. 5-28
6 Accessing the Camera..............................................................................................6-1
6.1 Before use of the IP camera................................................................................6-1
6.2 System Requirements of PC ................................................................................6-1
6.3 Installing Setup utility to thePC............................................................................6-2

IM 85A7C03-16E
TOC-2
6.4 Starts a Browser.........................................................................................6-3
6.5 Changing default password.....................................................................6-3
7 Accessing the Video streams........................................................................7-1
7.1 Home (Viewer Screen)................................................................................7-1
7.1.1 Viewer setting-field.............................................................. 7-1
7.1.2 Viewer Console-field............................................................ 7-1
7.1.3 Language setting-field......................................................... 7-2
7.1.4 Title Bar ................................................................................ 7-3
7.1.5 Status indicator.................................................................... 7-5
7.2 Camera Configuration................................................................................7-5
7.2.1 Preset.................................................................................... 7-5
7.2.2 Camera Control.................................................................... 7-9
7.2.3 OSD...................................................................................... 7-10
7.2.4 Video.................................................................................... 7-11
7.2.5 Multi Screen ......................................................................... 7-12
7.2.6 Detail .................................................................................... 7-13
7.3 Network Configuration..............................................................................7-17
7.3.1 LAN ....................................................................................... 7-17
7.3.2 Access IP.............................................................................. 7-18
7.3.3 Stream Priority..................................................................... 7-18
7.3.4 Session List.......................................................................... 7-19
7.3.5 NTP........................................................................................ 7-19
7.3.6 FTP........................................................................................ 7-20
7.3.7 SNMP .................................................................................... 7-21
7.3.8 Protocols.............................................................................. 7-22
7.4 System Configuration.................................................................................7-23
7.4.1 Server Name......................................................................... 7-23
7.4.2 Users..................................................................................... 7-23
7.4.3 Time ...................................................................................... 7-24
7.4.4 Configuration ....................................................................... 7-25
7.4.5 Logs...................................................................................... 7-26
7.4.6 Update................................................................................... 7-28
7.4.7 Reboot .................................................................................. 7-28
7.5 ONVIF ................................................................................................... 7-29
7.5.1 Profile.................................................................................... 7-29
7.5.2 WS-Discovery....................................................................... 7-29
8 Troubleshooting..................................................................................... 8-1
8.1 Viewer screen...............................................................................................8-1
8.2 Login screen........................................................................................ 8-2
8.3 Turning operation................................................................................ 8-2
9 Hardware Maintenance .......................................................................... 9-1
9.1 Inspection of the Main body.......................................................................9-1
9.2 Wiper Exchanging.......................................................................................9-2
9.3 Inspection of the JB............................................................................ 9-3
9.4 Part Exchanging / Adding................................................................... 9-3
10 Repair ................................................................................................. 10-1
11 Warranty Rules................................................................................... 11-1
A INSTALLATION-OPERATING PRECAUTIONS FOR FLAMEPROOF...... A-1
B ATEX/IECEx Certification................................................................................... B-1
C CSA Explosionproof............................................................................................ C-1

IM 85A7C03-16E
1. Introduction
<1.Introduction> 1-1
Thank youfor purchasingPan-TiltZoomTypeCameraFIELDEYEFC33E/FC33U.
ThisUser’s Manual describeshandlingprecautionsandtheinstallation,cabling,and operation
instructions.Readthismanualto takefull advantageof theproduct’sfunctions anduseitproperly.
If anymodifications of thespecification,construction,or apartor component usedmay beexpected
tonegativelyaffectthefunctionalityor performance,suchmodificationswill notbeincorporatedinto
thismanualinsomecases.
Weassumeno responsibilityif this equipmentmaybeunableto achieve the predeterminedfunction
dueto arepairthatyoumadewithoutour priorapproval.
If theproductfails,contactour service network, presentingthe specific details and developmentof
thefailuretogether with the model name, specification code, andthe instrumentcodedisplayedon
theproduct’snameplate.
Notice:
➢Thewholeor anypartof thismanual maynotbe reprintedor reproducedwithout our priorwritten
permission
➢Theinformationcontainedinthismanualissubjecttochangewithoutnotice
➢All reasonableefforthas beenmadeto ensurethe accuracyof thecontentsof this manual.However,
if youhave any questionsor findanyerrors, omissionsand so on, please inform our representative
from whom you purchasedthe productor us sales department.
➢Regardlessof theabovementioned,weassumeno responsibilityfor any consequences resulting
from product operation that isbasedon thismanual.

IM 85A7C03-16E
Blank Page

IM 85A7C03-16E
2-1
<2.HandlingPrecautions>
2. HandlingPrecautions
Thisequipment isthoroughlyinspectedprior toshipping.Onceyou receive it,visually checkthe
appearanceof the equipmentto ensurethatithas not beendamaged.In addition,check thatthe
model name displayed on theequipment’s nameplateisas orderedbyreferring tothe “List of
model names and codes” and“Specifications for options” tablesincludedinSection 3.3.
The following table summarizes the components of this equipment:
Table 2-1 Standard attachment list
Name
Description
Pan-TiltTypeCamera Body
Check thatthemodel nameis thatof themodel beingordered.
WireTerminalTreatment Parts
•Theproduct comes witha singlevinylbag, as standard,
whichcontains three solderless terminals, a spatula cap,
and ahexagonwrench.
•SeeSection5.3forhowto usethem.
•Usethe hexagon wrench whenreplacing thewiper blade.
•(SeeSection 9, “Maintenance” for details.)
•Copper foil tape(See Section 5.6.2 for LANcable treatment)
Software (CD-R)
Plug-in software for controller PC (K7500XN)
User’s Manual (thisdocument)
IM85A7C03-16E
*TheUser’s Manualmaynot be attached, depending on the requirements at the ordering.
Sincethischapter describes cautions requiredfor handling,Readitcarefully and thoroughlyfirstof all.
For anyinformationnot foundinthischapter,seetherelevantsections.
2.1. TransportationPrecautions
To protect the equipment from damage that may arise due to a transportation accident, it should
betransportedtotheinstallationsiteinitsoriginalstateof shipmentas far as possible.
2.2. Storage Precautions
2.2.1.Selecta storage location meeting the following conditions:
(1) Thereis noexposureto rainor water.
(2) Thereis minimalvibrationor shock
(3) Thetemperatureand humidityshouldbeas closeas possibleto a normal temperature and
humidity(approximately+25°Cand 65% RH)
(4) Temperature: −40°C to +60°CHumidity: 5% to 95% RH (at +40°C)
(5) Whenstoring this equipment,keep itinits originalpacking state as far as possible

IM 85A7C03-16E
2-2
<2.HandlingPrecautions>
2.3. Precautions forInstallation Location
Thiscameraisdesignedtowithstandsevereenvironmentalconditions.
However, care should be taken for the followings to ensure long term stability of camera:
2.3.1.Ambient temperature
Avoidinstallingthe cameraina locationwithseveretemperaturegradientor significant temperature
fluctuation.If the camera is exposed to radiant heat, provide heat insulation or improve ventilation.
2.3.2.Atmosphericconditions
Avoidinstalling the cameraina corrosive atmosphere. If itis usedina corrosive atmosphere, ensure
thatitis wellventilated.
2.3.3. Shockand vibration
Thiscamerais alsodesignedto withstandshockandvibration. However,itshouldbeinstalled ina
locationwithminimal shockand vibration.
2.3.4. Natural disasters
Takemeasures for natural disasters including earthquakes,windand flood damages, and lightning
strikes.This cameracontainsabuilt-in arrester; howeverbecauseitonlyconstitutes theminimum
configuration,itisrecommended that an additionallightning protector such as an arrester be
provided.
2.4. Precautions on pressure resistance and
explosionprevention
Theexplosion-prooftypeFC33Ehas beenproducedsothatitcanbeusedinahazardous
atmospherewhere explosivegaseslistedinthe“Factory ElectricFacilityExplosion Prevention
Guidance” occurs.
To retainsafety,sufficient attentionshouldbepaidto installation,wiring, etc.withregard to a
pressure-resistantand explosion-proof device. In addition,restrictionsare imposed onmaintenance
andrepair thereof for safety.Be suretoread“Attachment A: Precautions on Pressure-Resistantand
Explosion-Proof TypeDevices” describedat theend of this manual.

3-1
<3. Overview>
IM 85A7C03-16E
3. Overview
FC33E(Explosion-Proof) / FC33U(Outdoor)Pan TiltZoomtypeColorCamera issmalland
lightweight,and allowsfor installation ina smallspace. A web camera server function for
connecting to IP network isbeing installedinside. It hasan intelligent panning-tilting
movementand canstore preset points. Itis alsoavailablefor wide-range applications, such as
surveillance, monitoring andinstallation diagnosis and so on, withits excellent
environmentalresistance.
3.1 MainFeatures
Environmentalresistanceand downsizing
Theproductweighthas beensignificantlyreducedby(1) increasing thepackaging densityof the
exterior andinternalstainlessstructuresof SUS316Lthat aresuperior,instrengthand corrosion
resistance,to the conventional models andthus decreasingthegrossvolume(ratioto the
conventional companyproducts: approximately 2/3),and(2) reducing the thickness through use
of stainlesscasting for the exterior.
Inaddition,highcorrosionresistancehas beenimplementedbyusing electrolytic grinding for
+ surface treatment.
⚫Highsensitivityand highmagnification
Thesensitivityof thiscameraisso highthat itcanshootobjects withoutitsdedicatedlighting even
inalocationwhereconventionalmodelscouldnot shootthem.
The zoom magnificationhas alsobeenincreasedbya factorof 30for optical zooming and12for
electronic zooming,therebyshooting more remote,smaller objects clearly.
⚫Control systems and VMS
If the CCTV system including the FC33 consists of numbers of IP cameras, introducing a VMS
(Video Management System/Software) is recommended.
Recommending VMS products for the FC33 are shown below:
Products name (References)
Scalability of CCTV network
(numbers of Cameras under controlling)
XProtect Express
1-7
XProtect Professional
8-25
XProtect Enterprise
No limitation
XProtect®Expert
No limitation
Note: The table above may not be latest information. Please refer to Milestone Systems of
each regional company for more detail.
⚫Excellent environmental resistance
The operating temperature rangeof −40 to+60°Cwithwaterproof (IP Grade: IP66)and
dustproof featuresensurethatis availableinsevereenvironmental conditionsinaprocess
controlplantor factory. In addition,boththecameracaseand bodyaremade up of castingsand
have a robustconstruction.

3-2
<3. Overview>
IM 85A7C03-16E
3.2 ComponentNamesandFunctions
Model FC33is capable of outputting image signals from the built-in camera block while performing
actions such as panning, tilting, or zooming by using it in combination with various controllers.
Figure3.1showstheFC33componentnames.
Shade (option)
Main case Hood (option)
Full HDIP type is different appearance
Main nameplate
Base box*
Figure3.1 Componentsame
Table 3-1 Components function
Name
Function
Basebox
Equipped witha DC power supplyand noisefilter.
Maincase
Madeup of castingsso that thisis availableinsevere environmental
conditions, includingthe waterproof and dustproof features. Houses
maincomponentssuch as the pulsemotor, warm gear,and signal
processing circuit.The caseis rotatedby panning.
Shade(option)
Installed onthetopof themaincase, and protectsthe top from direct
sunlight.
Camerahousing
Housingof camerablock.
Hood(option)
Installed onthetopof the camerahousing, and protects the camera
from wind,rain,and snow.
Wiper (selected inbasic specification)
Cleans thewindow glass surface. Remotely operable.
Power cable
Cablethrough which power is suppliedto FC33U(see Section5,
“Warning”).
Compositecable
Acollectionof EthernetandRelaycontactsignal
Camera housing
Composite Cable:
: Ethernet and Relay connection;
: Std. length 5 m, /L10 (option) is available.
Power cable:
→Both types: Std. length 5 m, /L10 (option) is available
Tag plate (TAGNO)
(option)
Wiper (option)

IM 85A7C03-16E
3-3
<3. Overview>
3.3 Standard Specifications
⚫Video
Image Sensor 1/2.8" CMOS
Frame rate 1fps to 60 fps
Effective Pixels Up to 1920x 1080 pixels (2.13 Megapixels)
Video S/N > 50 dB
White Balance ATW (auto tracing white balance)
Zoom Magnification (30x optical) x (12x digital)
Lens f: 4.3 mm –129 mm, F1.6 - 4.7 (with auto focus)
Angle of View 63.7° (wide-angle) to 2.3° (telephoto)
Compression H.264, MJPEG
Minimum illumination
Normal Sensitivity
ICR-Off mode
0.1lux (1/30 sec, 50%)
0.013 lux (1/4 sec, 1/3 sec, 50%)
CR-On mode
0.006 lux (1/30 sec, 50%)
High Sensitivity
ICR-Off mode
0.01 lux (1/30 sec, 50%)
0.0013 lux (1/4 sec, 1/3 sec, 50%)
ICR-On mode
0.0015 lux (1/30 sec, 50%)
0.0008 lux (1/4 sec, 1/3 sec, 30%)
⚫I/O
Interface 10BASE-T/100BASE-TX(Note), IEEE 802.3i/u, Cat 5/5e Cable
Client PC requirements Windows 7 or Windows10 (Browser: Internet Explorer 11 only)
Password level Administrator / User (when networkloginvia PC)
Communication ONVIF® (Profile S),
Fieldeye command (Web application for Full HDIP type)
Supported Protocols: IPv4, TCP/IP, UDP/IP, HTTP,HTTPS, RTSP, RTP, NTP, SNMP
Delivery System Unicast/ Multicast
Priority Stream Up to 2 client IP address (TCP/IP stream)
Note: (At an "output-terminal-end" of internal Encoder Board)
⚫Video encoding function
No.
Item
Description
Note
1
Video encode system
JPEG / H.264
2
Image size
Refer to table 4.1 Image Size
3
Frame rate
1fps ～60 fps
Selectable
4
Bit rate
196kbps～20Mbps
CBR/VBR
5
Profile
Base Line/ Main / High
6
Encode
Single / Dual
⚫Main body
Housing Material Die Casted SS316L (Stainless steel) no welding parts
Finish Electrolytic Polishing
Weight 20kg (except cable(s))
Cable Entry (2-port)
- For Composite-cable input (LAN-cable and Relay-connection lines). (Std. length: 5m)
- For Power-cable input (Std. length: 5m)
⚫Mechanical
Pan Operation 360° continuous
Tilt Operation 180° (0±90°)
Rotation SpeedUp to Pan-tilt 40°/sec
Installation style Upright/Inverted
⚫Electrical
Power Supply (rated value): 100VAC to 240VAC, 50Hz or 60Hz
Power Consumption 30W (heater on) / 24W (heater off), 60VA (0.6A)
Relay driving circuit Single (1) dry contact, Max: DC 48 V, 100mA

IM 85A7C03-16E
3-4
<3. Overview>
⚫Environment
Operation Temperature/Humidity −40°C to +60°C (-40°F to +140°F)
Storage Temperature/Humidity −40°C to +60°C / 5% to 95% RH (at 40°C)
Installation altitude 2000 m (max)
⚫Others
Presetpoints 128 point, Preset Accuracy: ±0.25° (PAN/ TILT)
Defroster Standard equipment
⚫Cable Gland
Type CGW-16 manufactured by Japan Safety Systems Inc. of 2 are being attached into the Base
box, as shown below:
Specification: A, B andL of the CGW-16 above:
A
B
Packing
Internal
Diameter
[mm]
Range of
Cable
Outer
diameter
[mm]
Cable
Outer
diameter to
be used
[mm]
L
**(Note)
Material
➢Nominal designation
of screw thread: M20
➢Pitch of thread: 1.5
mm
➢Quality of FIT: 6H6g
ATEX/IECEx (FC33E-D*E)
➢Nominal designation of screw
thread: M20
➢Pitch of thread: 1.5 mm
➢Threads engaged:11.8 mm +1.8,-0
➢Depth of engagement:7.9 +1,-0
JAPAN
➢Nominal designation of screw
thread: G1/2
➢Pitch of thread: 1.814 mm
➢Threads engaged:11.8 mm +1.8,-0
➢Depth of engagement:6.5 +1,-0
φ10
φ9
to
φ10
φ9.4
16.56
mm
➢Body:
SUS316L
➢Packing:
SILICONE
➢O-ring:
SILICONE
φ12
φ11
to
φ12
φ11.6
16.37
mm
**(Note): PACKING TIGHTENING LENGTH
Figure3.2 Cable Glands on the Base box

IM 85A7C03-16E
3-5
<3. Overview>
⚫Certifications (FC33E)
ATEX Certificated: CML 14 ATEX 1097Xx1
Equipment intended for usein Potentially Explosive AtmospheresDirective 2014/34/EU
Equipment FC33E*** Pan & Tilt CCTV Cameras
EN 60079-0:2018, EN 60079-1:2014, EN 60079-31:2014
Type of Protection and Marking code:
Ex db IIC T5 Gb
Ex tb IIIC T100°C Db
FC33E-***1*/*: Ambient Temperature: -40°C to +60°C
FC33E-***1*/*: Rating: 100VAC to 240VAC ~0.6A 50/60Hz
IECEx Certificate of Conformity IECEx CML 16.0096X
Equipment: FC33E*** Pan & Tilt CCTV Cameras
Type of Protection: Flameproof "db", Dust Ingition "tb"
Marking
Ex db IIC T5 Gb
Ex tb IIIC T100°C Db
Ta = -40°C to +60°C
Standards:
IEC 60079-0:2017 Edition 7.0, IEC 60079-1:2014-06 Edition 7.0, IEC 60079-31:2013 Edition 2
CSA Explosion-proof approval: Certificate 80009215
Type Designation FC33E - * a b c * /*
PRODUCTS FC33E - ***2*/*:
(Where, 2above: CSA CERTIFICATION)
CLASS 2258 02 - PROCESS CONTROL EQUIPMENT - For Hazardous Locations
Ex db IIC T5 Gb
Rated 100 Vac to 240 Vac, 50/60 Hz, ambient range: -40°C to 60°C
Pan Tilt Zoom Type CCTV Cameras Models FC33E***
APPLICABLE REQUIREMENTS:
CAN/CSA-C22.2 No. 60079-0:19, CAN/CSA-C22.2 No. 60079-1:16, CAN/CSA-C22.2 No. 61010-1-12,
CSA C22.2 No. 94.2-15
CONDITIONS OF ACCEPTABILITY:
1. The above models are permanently connected,
Equipment Class I, Pollution Degree 2, Overvoltage Category II
2. Mode of operation: Continuous
3. Environmental Conditions: -40 to 60°C, 2000m max., 20 to 95% RH
4. This equipment employs flamepath joints that have not been tested at the maximum joint dimensions
and minimum flamepath lengths permitted by the standard.
When the equipment is to be repaired,maintained or inspected, contact themanufacturer for
information on dimensions.
5. Installation must complywith Canadian Electrical Code wiring method for Zone 1.
NOTES:
1. For Canadian Installations, housing of the Base box mustbe bonded to ground according to Section
18 of the CEC, Part 1
*

IM 85A7C03-16E
3-6
<3. Overview>
⚫Other Certifications (FC33E/U)
Degree of Protection of enclosure: IP66
EMC: EN50130-4 (2011) A1 (2014), EN55032 (2012) class A,
EN61000-3-2(2014), EN61000-3-3(2013)
LVD EN61010-1(2010)
RoHS EN50581(2012)
CSA Certificate: 80012590:
Product CLASS 2252 06 –PROCESS CONTROL EQUIPMENT
Pan Tilt Zoom Type CCTV Camera,
Model nos. FC33U and FC33E series, rated 100-240 V ac, 50/60 Hz, 0.6 A maximum, Type 4X
Notes:
1. The above models are permanently connected, Equipment Class I, Pollution Degree 2 Overvoltage
Category II
2. Mode of operation: Continuous
3. Environmental Conditions: -40 to 60°C, 2000 m max., 20 to 95% RH
⚫WEEE
> This product is designed only for use in large-scale fixed installations only and,
therefore, is out of scope of the WEEE Directive. The WEEE Directive does not apply.
> This product should be disposed in accordance with local and national
legislation/regulations. The WEEE Directive is only valid in the EU.

IM 85A7C03-16E
3-7
<3. Overview>
⚫Full HDIP type. Figure3.3
⚫Figure 3.3 contains internal block diagrams (overview and detailed diagrams)
<Configurationdiagram, overview>
Figure3.3 Block Diagram of FC33
・AC/ DC Converter
External- Contact
Ctrl.
2
CTRL.
CMOS ImageSensor
CTRL
Peripheral CTRL.
CTRL
5V-12VDC

IM 85A7C03-16E
3-8
<3. Overview>
⚫Listof model namesand codes
Table 3-2 Model codes
⚫Specifications foroptions
Table 3-3 Option codes for the main body only
⚫Accessories
Table 3-4 Standard accessories
No.
Name
QTY.
Remarks
1
HEXAGONWRENCH (LARGE)
1
Supplied collectively in asinglebag.
2
HEXAGONWRENCH (SMALL)
1
3
COPPER FOIL
1 (length:3cm)
4
CABLE BUNDLED BAND
4
5
GUIDEAUNCE SHEET FOR
NETWORK CONFIGURATION
1
6
INSTRUCTION MANUAL
(IM85A7C03-16E)
1 (may remove by specified
at ordering)
7
Software
1 (CD-R)
Plug-in software for browser
Model
Suffix
Code
OOption
Code
Description
FC33E
Explosion-proof pan-tilt zoom color camera
FC33U
Weather-proof pan-tilt zoom color camera
Camera
type
-D
HDIP
High-sensitivity 1/2.8” CMOS, 1920x1080 pixels ,30x optical zoom
Wiper
W
With wiper
N
Without wiper
Control type
E
10BASE-T/100BASE-TX (at an "output-terminal-end" of internal Encoder Board)
Explosion
Protected type
(Cable entry)
0
Explosion Protection in Japan only, (G1/2 female thread, Cable glands)
1
ATEX/IECEx Certification (M20 female thread, at each Cable gland on the Base Box)
2
CSA Explosionproof (M20 female thread, at each Cable gland on the Base Box)
Installation
S
Upright
U
Inverted
for FC33E/U
Option Code
Description
Cableextension
/L10
Cablelength10m
Installationof tagplate
/T
Installationof stainless-steel tag plate, Up to 15 letters (alpha-numeral
combination codes) can be specified
Withhood (upright)
/SHD
Hood(Upright) for Full HDIP type
Withhood(inverted)
/UHD
Hood(Inverted) for Full HDIP type
Withshade
/SD
Shade(for themain body)
Replacement adapter base
/ADP
Replacement adapter base

IM 85A7C03-16E
3-9
<3. Overview>
3.4 External dimension
⚫Bodyof modelFC33-DWE1S
Uprighttype
Unit: mm
Figure3.4 Upright type of FC33-DWE1S