Yosemite TWIN-PEAK2 User manual

TWIN-PEAK2
Owner’s Manual
WARNING : Read and follow these instructions carefully and be cautious of all warnings shown throughout.
UL
R

P1
Warning: To avoid the risks of fire, electrical shock or injury,
please observe the following:
READ AND SAVE THESE INSTRUCTIONS
1. To ensure the correct and complete installation, be sure to read the instructions and review the diagrams
carefully and thoroughly before beginning installation.
2. If possible, mount the ceiling fan on a ceiling joist. The joist must be able to support the motion and weight
of the moving fan. If the fan will be mounted on a ceiling outlet box, a 4" x 2-1/8" deep METAL octagon box is
required; one UL listed as "suitable for fan support ". The box and its supporting members must not be able
to twist or work loose. DO NOT USE PLASTIC BOXES. Installation on a concrete ceiling should be
performed by qualified personnel.
3. Blades should be attached after motor housing is hung and in place. Fan motor housing should be kept in
the carton until ready to be installed to protect its finish. If you are installing more than one ceiling fan, make
sure that you do not mix fan blade sets.
4. Make sure that your installation site will not allow rotating fan blades to come in contact with any object.
Blades should be at least 7 feet from the floor when fan is in operation.
5. To avoid any possible accidents such as electric shock, be sure ceiling fan is not connected to power source
before wiring. All electrical connections must be made in accordance with local codes, ordinances and/or
the National Electric Code. If you are unfamiliar with the methods of installing electrical wiring and
products, secure the services of a qualified and licensed electrician as well as someone who can check the
strength of the supportive ceiling members and make the proper installations and connections.
6. See wire connection instruction for your guide. Electrical diagrams are for reference only. Read the
instructions carefully and connect wires correctly and completely.
7. After making electrical connections, spliced conductors should be turned upward and pushed carefully up
into the outlet box. The wires should be spread apart from the grounded conductor. Ground conductor
should be placed opposite to the outlet box from the "HOT" wires.
8. After fan is completely installed, double check everything to make sure that all connections are secure to
prevent fan from falling and/or causing damage or injury.
9. The fan can be used immediately after installation. The bearings are adequately charged with grease so
that, under normal condition, further lubrication should not be necessary.
Important Notes:
1. The fan must be turned off and at a complete stop before reversing fan direction.
2. Light kits that are not packed with the fan must be UL or CUL listed and should be installed per light kit's
installation instructions.
3. This fan is suitable for indoor locations only.

Blade Holder
Fan
Assembly
18” Downrod
Assembly
Yoke
Cover
Mounting
Bracket
Canopy
Plastic Blade
P2
Screw 2 pcs
Wire Nut 6 pcs
Blade Balance Kit 1 pc
Blade Screw 25 pcs
Paper Washer 25 pcs
Mounting Screw 2 pcs
Spring Washer 3 pcs
Lock Washer 3 pcs
Wood Screw 3 pcs
Tooth Washer 3 pcs
Motor Screw 1 pcs
Wire Nuts 3pcs
Hardware bag
OFF OFF OFF
Outlet Box
Mounting
Bracket
1.Unpack and inspect the fan carefully to be certain that all contents are
included. Identify and check the parts referred to the drawing below.
I - Opening of the box
2. 3.
4.
Turn off power at the breaker
box to avoid possible
electrical shock.
Use a metal outlet box suitable for
fan support.
Be sure that the box can support
a minimum weight of 40 pounds.
Secure the outlet box directly to the
building structure using wood
screws (provided).
Install the mounting bracket
to outlet box in the ceiling
using the washers and the
mounting screws provided
in the hardware bag.
Do not use existing
mounting bracket
in the outlet box.
Remote Control
Transmitter
Hex Nut 1 pc
Spring Washer 1 pc
Screw For Spring 3 pcs
Screw For Grill 3 pcs
Spring 3 pcs
Light Kit Hardware bag
Light Kit Fitter
Grill
Suitable for use with solid - state speed control
Glass Shade

5a. 1.Insert the Yoke Cover and Canopy through downrod
assembly as shown (5a).
2.Feed motor lead wires through downrod assembly.
3.Insert the downrod assembly into yoke.
1.Insert the cross pin through Yoke and downrod and
secure with Cotter Pin.
2.Tighten both set screws to further secure downrod.
3.Tighten hex nuts existing on set screws toward yoke
to prevent set screws from loosening.
4.Pull down the yoke cover on top of housing.
5b.
5. Yoke & downrod assembly
(1)
Lift fan assembly onto mounting bracket.
(2)
Carefully lift fan assembly onto mounting bracket.
Rotate fan so that the ball engages the
ridge in the mounting bracket.
notch
6. Hanging the fan
Mounting
Bracket
Ball Notch
Mounting
Bracket
Receiver
Code Switches
Transmitter
Code Switches
P3
Yoke
Yoke Cover
Lead Wires
Downrod
Canopy
Cotter Pin
Cross Pin
Downrod Set Screws(2)
Hex Nut(2)
12
3
4
12
3
4
II - Remote Control
1.Prepare the parts of the remote control.
From House From Fan
( from downrod )
( from mounting bracket )
From Remote
( for ground wire )
( for light kit )
(AC-N)
(AC-L)
Black
White
Blue
Black
White
(Motor-N)
(Motor-L)
Secure with twist - lock wire nuts (Included).
White White
Black Black
Blue
Green
Green
Green
2. Setting the code on the transmitter.
2-1. Remove the battery cover of the remote control.
2-2. Slide code switches to your choice for an ON and OFF position. Use a small screwdriver to slide each
of the switches.
2-3. Install a 9V DC battery (included).
2-4. Install battery covers on transmitter.
3. Setting the code on the receiver:
3-1. Slide the code switches to the receiver. Be sure that the code is similar to the code set at the
transmitter.
4. For remote control wiring connection to the fan:
4-1. Follow the diagram below and be sure that exposed wires are secured inside wire nuts or the
terminal block.
4-2. When the wiring is completed, gently push wires into the junction box with wire nuts pointing upward.
Note: Wires from the house may vary in color and may not include ground wire (green).
Downrod
Assembly
Fan
Assembly

45°
0° Your fan is received in 0 degree.
Both motors are designed for 2 position-0/45 degree adjustment. Refer to following drawings for desired
motor positions.
III - Set Up Motor Position
1. Remove the set screw between yokes & bend the motor
Motor Yoke
Pipe Yoke
Set Screw
P4
2. Line up the angle labels as below.
For 45 degree For 0 degree
Motor Yoke
Pipe
Yoke
4
5
0
4
5
9
0
Motor Yoke 45 90
Pipe Yoke 45 0
Pipe
Yoke
Motor
Yoke
Motor Yoke 0
Pipe Yoke 45 0
Set screw
Set screw
3. Insert back the set screw removed from step 1 and tighten it.
(2)
Secure blade assembly to
the motor with motor screws
provided from .blade holder
(1)
Attach blade to blade arm with
screws & washers provided
in hardware bag. Make sure
that all screws are firmly tightened.
Washer
Blade Holder
Motor Screw
Motor
Screw
IV - Blades Installation:
Key Holes
Canopy
Screw
(1) Push up the canopy until the two canopy
screws on mounting bracket are engaged
with key holes in canopy.
Rotate the canopy slightly until the two
canopy screw heads are in the small end
of the key holes.
Tighten both canopy screws.
(2)
(3)
5.Canopy Installation
Blade Assembly

P5
Bulb
Light Kit
Fitter Switch
Housing. Screw
Grill & Glass
3. Attach grill and glass shade
assembly to light fixture with
three screws.
2. Place glass shade to grill
and secure with three springs
and screws.
Screw
Spring
1. Install bulbs
to
lamp holders on light fixture.
( E26 CFL bulb
13W x 2, included )
1. Wire Connections
VI - Light Kit Fitter Installation:
1-1 Take center nut off from switch housing cover.
1-2 Insert the existing wires from the light kit fitter passing
through the center hole and connect the wires from
the light kit fitter to the fan wires and secure with a
spring washer and a hex nut.
Note: White wire from the light kit fitter must connect to the
white wire from the fan and the black wire from the
light kit fitter to the black wire of the fan
1-3 Attach the light kit fitter to switch housing cover and
lock with three screws.
Switch Housing
Screw
Switch Housing
Cover
Black Wire
Light Kit
Fitter
White Wire
Wire Nut
Hex Nut
Spring Washer
TURN ON THE POWER. INSTALLATION IS SUCCESSFUL
AND THE FAN IS READY FOR OPERATION.
2. Bulbs and Glass Shade:
V.Scroll Kit Attachment
(1). Align scroll onto vertical downrod and horizontal bar
and secure connector to scroll with screws provided.
(2). Attach second scroll on other side with same step as above.
Horizontal Bar
Connector
Scroll
Top O f
Scroll
Connector
Downrod
(3). Secure two scrolls onto downrod
together with screws provided.
Center Nut