Zanussi ZWF 1210 User manual

User Manual 2
Benutzerinformation 19
EN
DE
ZWF 1210
Washing Machine
Waschmaschine

Contents
Safety information 2
Safety instructions 3
Product description 4
Control panel description 5
Programme Chart 5
Consumption values 7
Options 8
Settings 9
Before first use 9
Daily use 9
Hints and tips 12
Care and cleaning 13
Troubleshooting 14
Technical Data 16
Garantie, Garanzia, Guarantee 17
Subject to change without notice.
Safety information
Before the installation and use of the appliance, carefully read the
supplied instructions. The manufacturer is not responsible if an
incorrect installation and use causes injuries and damages.
Always keep the instructions with the appliance for future
reference.
Children and vulnerable people safety
•This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
•Do not let children play with the appliance.
•Keep all packaging away from children.
•Keep all detergents away from children.
•Keep children and pets away from the appliance door when it is
open.
•Cleaning and user maintenance shall not be made by children
without supervision.
General Safety
•Do not change the specification of this appliance.
•Obey the maximum load volume of 9 kg (refer to the
“Programme chart” chapter).
•The operating water pressure (minimum and maximum) must be
between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa).
2 www.zanussi.com

•The ventilation openings in the base (if applicable) must not be
obstructed by a carpet.
•The appliance is to be connected to the water mains using the
new supplied hose-sets. Old hose sets must not be reused.
•If the supply cord is damaged, it must be replaced by the
manufacturer, its Authorised Service Centre or similarly
qualified persons in order to avoid a hazard.
•Before maintenance, deactivate the appliance and disconnect
the mains plug from the mains socket.
•Do not use water spray and steam to clean the appliance.
•Clean the appliance with a moist soft cloth. Only use neutral
detergents. Do not use abrasive products, abrasive cleaning
pads, solvents or metal objects.
Safety instructions
Installation
• Remove all the packaging and the transit
bolts.
• Keep the transit bolts. When you move the
appliance again you must block the drum.
• Always be careful when you move the
appliance because it is heavy. Always wear
safety gloves.
• Do not install or use a damaged appliance.
• Obey the installation instruction supplied
with the appliance.
• Do not install or use the appliance where the
temperature is less than 0 °C or where it is
exposed to the weather.
• Make sure that the floor where you install the
appliance is flat, stable, heat resistant and
clean.
• Do not install the appliance where the
appliance door can not be fully opened.
• Make sure that there is air circulation
between the appliance and the floor.
• Adjust the feet to have the necessary space
between the appliance and the carpet.
• Do not install the appliance where the
appliance door can not be fully opened.
Electrical Connection
• The appliance must be earthed.
• Always use a correctly installed shockproof
socket.
• Make sure that the electrical information on
the rating plate agrees with the power
supply. If not, contact an electrician.
• Do not use multi-plug adapters and
extension cables.
• Make sure not to cause damage to the
mains plug and to the mains cable. Should
the mains cable need to be replaced, this
must be carried out by our Authorised
Service Centre.
• Connect the mains plug to the mains socket
only at the end of the installation. Make sure
that there is access to the mains plug after
the installation.
• Do not touch the mains cable or the mains
plug with wet hands.
• Do not pull the mains cable to disconnect
the appliance. Always pull the mains plug.
• Only for UK and Ireland: The appliance has a
13 amp mains plug. If it is necessary to
change the fuse in the mains plug, use a 13
amp ASTA (BS 1362) fuse.
• This appliance complies with the E.E.C.
Directives.
Water connection
• Make sure not to cause damage to the water
hoses.
• Before you connect the appliance to new
pipes or pipes not used for a long time, let
the water flow until it is clean.
www.zanussi.com 3

• The first time you use the appliance, make
sure that there is no leakage.
Use
WARNING!
Risk of injury, electrical shock, fire,
burns or damage to the appliance.
• Use this appliance in a household only.
• Obey the safety instructions on the
detergent packaging.
• Do not put flammable products or items that
are wet with flammable products in, near or
on the appliance.
• Make sure that you remove all metal objects
from the laundry.
• Do not put a container to collect possible
water leakage under the appliance. Contact
the Authorised Service Centre to ensure
which accessories can be used.
• Do not touch the glass of the door while a
programme operates. The glass can be hot.
Disposal
WARNING!
Risk of injury or suffocation.
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and discard it.
• Remove the door catch to prevent children
and pets to get closed in the appliance.
Product description
Appliance overview
1 2 3
5
6
4
1Worktop
2Detergent dispenser
3Control panel
4Door handle
5Rating plate
6Feet for the appliance level
4 www.zanussi.com

Control panel description
P
90
60
40
30
1200
1000
800
Ein/Aus
Marche/Arrêt
Kurz / Rapide
Intensiv /
Intensif
Bügelquick /
Anti-froissage
Spülen / Rinçage
Pumpen / Vidange
Schleudern /
Essorage
Koch-/Buntwäsche / Coton
Koch-/Buntwäsche / Coton ECO
Pflegeleicht / Synthétiques
Feinwäsche / Délicats
Wolle / Laine
Daunen / Couette
Mix 20 / Mixtes 20
9h
3h 6h
87621 3 4 5
1On / Off button (Ein/Aus Marche/Arrêt)
2Programme selection touchpad
3Temperature selection touchpad
4Spin selection touchpad
5Options selection touchpad
6Start/Pause touchpad
7Indicators:
Child lock indicator
Extra rinse indicator
Door locked indicator
8Delay start touchpad
Programme Chart
Programme
Temperature
range
Maximum load
Maximum spin
speed
Programme description
(Type of load and soil level)
30' @ 30°
30 °C 3 kg 800 rpm A short cycle for synthetics and delicate items with light soil level or for items to freshen up.
Koch-/Buntwäsche/
Coton
90 °C - Cold
9 kg
1200 rpm White cotton and coloured cotton. Normal soil and light soil.
Koch-/Bunt-
wäsche/Coton ECO
1)
60 °C - 40 °C
9 kg
1200 rpm White cotton and colour-fast cotton. Normal soil. The energy consumption decreases and the time of the washing
programme is extended.
Pflegeleicht/Synthé-
tiques
60 °C - Cold
3,5 kg
1200 rpm Synthetic items or mixed fabric items. Normal soil.
Feinwäsche/Délicats
40 °C - Cold 3,5 kg 1200 rpm Delicate fabrics as acrylics, viscose, polyester items. Normal soil.
www.zanussi.com 5

Programme
Temperature
range
Maximum load
Maximum spin
speed
Programme description
(Type of load and soil level)
Wolle/Laine
40 °C - Cold 2 kg 1200 rpm Machine washable wool, hand washable wool and
delicate fabrics with «hand washing» care symbol.2)
Daunen/Couette
60 °C - Cold 3 kg 800 rpm Special programme for one synthetic blanket, duvet, bedspread and so on.
Mix 20°/Mixtes 20°
20 °C 2 kg 1200 rpm Special programme for cotton, synthetic and mixed fabrics with light soil. Set this programme to decrease the energy
consumption. Make sure that the detergent is for low tem-
perature in order to have good washing results3).
1) Standard programmes for the Energy Label consumption values. According to regulation 1061/2010, these programmes are re-
spectively the «Standard 60°C cotton programme» and the «Standard 40°C cotton programme». They are the most efficient programmes in
terms of combined energy and water consumption for washing normally soiled cotton laundry.
The water temperature of the washing phase may differ from the temperature declared for the selected programme.
2) During this cycle the drum rotates slowly to ensure a gentle washing. It can seem that the drum doesn't rotate or doesn't rotate properly.
Consider this as a normal functioning of the appliance.
3) No temperature indicator is on .
Programme options compatibility
Programme Kur
z/
Ra
pid
e1)
In-
ten-
siv/
In-
ten-
sif
Bü-
gel-
qui
ck/
An-
ti-
froi
ssa
ge
Spü-
len/
Rin-
çage
Pum
pen/
Vi-
dang
e
Schle
uder
n/
Es-
sor-
age
30' @ 30° ■■ ■ ■
Koch-/Buntwä-
sche/Coton ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
Koch-/Buntwä-
sche/Coton ECO ■ ■ ■ ■ ■ ■ ■ ■
Pflegeleicht/
Synthétiques ■ ■ ■ ■ ■ ■ ■ ■ ■ ■
Feinwäsche/Déli-
cats ■ ■ ■ ■ ■ ■ ■ ■ ■
Wolle/Laine ■ ■ ■ ■ ■ ■
6 www.zanussi.com

Programme Kur
z/
Ra
pid
e1)
In-
ten-
siv/
In-
ten-
sif
Bü-
gel-
qui
ck/
An-
ti-
froi
ssa
ge
Spü-
len/
Rin-
çage
Pum
pen/
Vi-
dang
e
Schle
uder
n/
Es-
sor-
age
Daunen/Couette ■ ■ ■ ■ ■ ■
Mix 20°/Mixtes
20° ■ ■ ■ ■■ ■ ■
1) When you set this option, we recommend that you decrease the quantity of the laundry. It is possible to keep the full load but the washing
results can be unsatisfactory. Recommended load: cotton: 4,5 kg, synthetics and delicates: 2,5 kg.
Consumption values
The data of this table are approximate. Different causes can change the data: the quan-
tity and type of laundry, the water and ambient temperature.
Programmes Load
(kg) Energy consump-
tion (kWh)
Water con-
sumption
(litre)
Approxi-
mate pro-
gramme
duration
(minutes)
Remaining
moisture
(%)1)
Koch-/Buntwäsche/
Coton 60 °C 9 1,58 84 175 53
Koch-/Buntwäsche/
Coton 40 °C 9 1,01 82 174 53
Pflegeleicht/Synthé-
tiques 40 °C 3,5 0,74 61 122 35
Feinwäsche/Délicats
40 °C 3,5 0,54 62 74 35
Wolle/Laine 30 °C 2 0,30 63 57 30
Standard cotton programmes
Standard 60 °C cotton 9 1,03 49 220 53
Standard 60 °C cotton 4,5 0,77 40 187 53
Standard 40 °C cotton 4,5 0,62 40 181 53
1) At the end of spin phase.
www.zanussi.com 7

Off Mode (W) Left On Mode (W)
0,48 0,48
The information given in the chart above are in compliance with the EU Commission regulation
1015/2010 implementing directive 2009/125/EC.
Options
Temperature
With this option you can change the default
temperature.
Indicator = cold water.
The indicator of the set temperature comes on.
Spin
With this option you can change the default
spin speed.
The indicator of the set speed comes on.
Additional spin options:
No Spin
• Set this option to deactivate all spin phases.
Only the drain phase is available.
• The related indicator comes on.
• Set this option for very delicate fabrics.
• The rinses phase uses more water for some
washing programmes.
Rinse Hold
• Set this option to prevent the laundry
creases.
• The related indicator comes on.
• There is a water in the drum when the
programme is completed.
• The drum turns regularly to prevent the
laundry creases.
• The door stays locked. You must drain the
water to unlock the door.
To drain the water refer to ‘At the
end of the programme’.
Kurz/ Rapide
With this option you can decrease the
programme duration.
Use this option for items with light soil or items
to refresh.
The related indicator comes on.
Intensiv/ Intensif
With this option you can wash very soiled
laundry.
The washing cycle lasts longer with this option.
The related indicator comes on.
Bügelquick/ Anti-froissage
The appliance carefully washes and spins the
laundry to prevent the creases.
The appliance decreases the spin speed, uses
more water and adapts the programme duration
to the type of laundry.
The related indicator comes on.
Spülen/ Rinçage
With this option you can perform only a last
rinse of a selected washing programme.
If you set also the Extra Rinse function ( ) the
appliance adds two or more rinses.
The related indicator comes on.
Pumpen/ Vidange Schleudern/
Essorage
With this option you can perform the spin and
drain cycle.
The spin phase is suitable to the washing
programme you set.
If you set also the No Spin ( )
option, the appliance only drains.
Delay Start
With this option you can delay the start of a
programme by 9, 6 or 3 hours.
The indicator of the set value is on.
8 www.zanussi.com

Extra Rinse
With this option you can add some rinses to a
washing programme.
Use this option for persons allergic to
detergents and in areas where the water is soft.
The related indicator comes on.1
Settings
Extra Rinse
With this option you can permanently have an
extra rinse when you set a new programme.
• To activate/deactivate this option touch
the buttons and at the same time until
the indicator comes on/goes off.
Child Lock
With this option you can prevent that the
children play with the control panel.
• To activate/deactivate this option, touch
the buttons and at the same time until
the indicator comes on/goes off.
Activate this option after you touch the button
: the buttons are locked (except for the
button ) .
This option stays active even when
you switch off the appliance.
Acoustic signals
The acoustic signals operate when:
• The programme is completed.
• The appliance has a malfunction.
To deactivate/activate the acoustic signals,
touch the buttons and at the same time
for 4 seconds.
If you deactivate the acoustic
signals, they continue operate when
the appliance has a malfunction.
Before first use
1. Put a small quantity of detergent in the
compartment for washing phase.
2. Set and start a programme for cotton at the
highest temperature without laundry.
This removes all possible dirt from the drum and
the tub.
Daily use
WARNING!
Refer to Safety chapters.
Loading the laundry
Open the water tap. Connect the mains plug to
the mains socket.
1. Pull the door handle to open the appliance
door.
2. Put the laundry in the drum, one item at a
time.
3. Shake the items before you put them in the
appliance.
1 See in "Settings" how to activate this option.
www.zanussi.com 9

Make sure not to put too much laundry in the
drum. Refer to max. loads indicated in
"Programme chart".
4. Close the door.
CAUTION!
Make sure
that no
laundry
stays
between the
seal and the
door. There
is a risk of
water
leakage or
damage to
the laundry.
Using detergent and additives
1. Measure out the
detergent and the
fabric conditioner.
2. Carefully close the
detergent drawer.
Detergent compartments
Detergent compartment for wash-
ing phase.
If you use liquid detergent, put it
immediately before you start the
programme.
Compartment for liquid additives
(fabric conditioner, starch).
CAUTION!
Do not exceed the
MAX level.
Flap for powder or liquid detergent.
Liquid or powder detergent
A
The default position of
the flap is A(powder
detergent).
To use liquid detergent:
1. Remove the drawer.
Push the drawer edge in
the place with the arrow
(PUSH) to remove the
drawer easily.
B
2. Adjust the flap in
position B.
3. Put back the drawer in
the recess.
When you use the liquid detergent:
• Do not use gelatinous or thick
liquid detergents.
• Do not put more liquid then 120
ml.
• Do not set the delay start.
A
When the flap is in
position B and you want
to use powder detergent:
1. Remove the drawer.
2. Adjust the flap in
position A.
3. Put back the drawer
in the recess.
• Measure out the detergent and the fabric
conditioner.
• Put the detergent and the fabric conditioner
into the compartments.
• Carefully close the detergent drawer.
Activating the appliance
Press and hold for a couple of seconds the
button to activate or deactivate the appliance.
10 www.zanussi.com

A tune sounds when the appliance is activated.
The appliance performs a start up animation.
The animation quickly shows each washing
programme and the default temperature and
spin settings.
Setting a programme
1. Touch the programme button and set the
programme:
• The indicator of the button flashes
slowly.
2. If necessary, change the temperature and
the spin speed or add available options.
When you activate an option, the indicator
of the set option comes on.
If you set something incorrect, the
indicator of the button flashes
red three times.
Starting a programme without the delay
start
Touch the button .
• The indicator of the button stops to
flash and stays on.
• The programme starts, the door locks,
the indicator is on.
The drain pump can operate for a
short time at the beginning of the
washing cycle.
Starting a programme with the delay
start
The start of the programme can be delayed by
9, 6 or 3 hours.
1. Touch the button to choose the delay
you want to set.
The indicator of the selected delay is on.
2. Touch the button :
• The appliance starts the countdown.
• When the countdown is completed, the
programme starts automatically.
You can cancel or change the set of
the delay start before you touch the
button . After touching the
button you can only cancel the
delay.
To cancel the delay start:
1. Touch the button to set the appliance
to pause.
2. Touch the button until the indicator of
the set delay goes off.
Touch the button again to start the
programme immediately.
Interrupting a programme and changing
the options
You can change only some options before they
operate.
1. Touch .
The indicator of this button flashes.
2. Change the options.
3. Touch again.
The programme continues.
Cancelling a programme
1. Press the button for some seconds to
cancel the programme and to deactivate the
appliance.
2. Press the same button again to activate the
appliance. Now, you can set a new washing
programme.
The appliance does not drain the
water. The water left in a drum can
be used for the next washing cycle.
Opening the door
While a programme or the delay start operates,
the appliance door is locked. The indicator
is on.
CAUTION!
If the temperature and level of the
water in the drum are too high, you
cannot open the door.
To open the door during the first minutes
of the cycle or when the delay start
operates:
1. Touch the button to pause the
appliance.
2. Wait until the indicator goes off.
3. You can open the door.
4. Close the door and touch the button
again. The programme (or the delay start)
continues.
www.zanussi.com 11

At the end of the programme
• The appliance stops automatically.
• The acoustic signal operates (if it is
activated).
• The indicator of the button goes off.
• The door lock indicator goes off.
• You can open the door.
• Remove the laundry from the appliance.
Make sure that the drum is empty.
• Press the button for some seconds to
deactivate the appliance.
• Close the water tap.
• Keep the door and the detergent drawer
ajar, to prevent the mildew and odours.
The washing programme is completed,
but there is water in the drum:
• The drum turns regularly to prevent the
creases in the laundry.
• The indicator flashes to remind you to
drain the water.
• The door lock indicator is on. The
indicator of button flashes. The door
stays locked.
• You must drain the water to open the door.
Draining the water:
1. To drain the water.
• Touch the button . The appliance
drains the water and spins with the
maximum spin speed for selected
washing programme.
• Alternatively, touch the button to
change the spin speed and then touch
the button . The appliance drains the
water and spins. If you set , the
appliance only drains.
2. When the programme is completed and the
door lock indicator goes off, you can
open the door.
3. Press the button for some seconds to
deactivate the appliance.
The appliance drains and spins
automatically after approximately 18
hours (except for Wool programme).
AUTO-OFF option
The AUTO-OFF stand-by option automatically
deactivates the appliance to decrease the
energy consumption. All the indicators go off
when :
• You do not use the appliance for 5 minutes
before you touch .
Press the button to activate the appliance
again.
• After 5 minutes from the end of the washing
programme.
Press the button to activate the appliance
again.
Touch the button if you want to set a new
cycle.
Hints and tips
The laundry load
• Divide the laundry in: white, coloured,
synthetics, delicates and wool.
• Obey the washing instructions that are on
the laundry care labels.
• Do not wash together white and coloured
items.
• Some coloured items can discolour with the
first wash. We recommend that you wash
them separately for the first times.
• Button up pillowcases, close zippers, hooks
and poppers. Tie up belts.
• Empty the pockets and unfold the items.
• Turn inside out multilayered fabrics, wool
and items with painted illustrations.
• Remove hard stains.
• Wash with a special detergent heavy soil
stains.
• Be careful with the curtains. Remove the
hooks or put the curtains in a washing bag
or pillowcase.
• Do not wash in the appliance laundry without
hems or with cuts. Use a washing bag to
wash small and/or delicate items (e.g.
underwired bras, belts, tights, etc. ).
• A very small load can cause balance
problems with the spin phase. If this occurs,
adjust manually the items in the tub and start
the spin phase again.
Stubborn stains
For some stains, water and detergent is not
sufficient.
12 www.zanussi.com

We recommend that you remove these stains
before you put the items in the appliance.
Special stain removers are available. Use the
special stain remover that is applicable to the
type of stain and fabric.
Detergents and additives
• Only use detergents and additives specially
made for washing machines:
– powder detergents for all types of fabric,
– powder detergents for delicate fabrics
(40 °C max) and woollens,
– liquid detergents, preferably for low
temperature wash programmes (60 °C
max) for all types of fabric, or special for
woollens only.
• Do not mix different types of detergents.
• To help the environment, do not use more
than the correct quantity of detergent.
• Obey the instructions that you find on the on
packaging of these products.
• Use the correct products for the type and
colour of the fabric, the programme
temperature and the level of soil.
• If your appliance has not the detergent
dispenser with the flap device, add the liquid
detergents with a dosing ball (supplied by
the detergent's manufacturer).
Ecological hints
• Set a programme without the prewash
phase to wash laundry with normal soil.
• Always start a washing programme with the
maximum load of laundry.
• If necessary, use a stain remover when you
set a programme with a low temperature.
• To use the correct quantity of the detergent,
check the water hardness of your domestic
system
Water hardness
If the water hardness in your area is high or
moderate, we recommend that you use a water
softener for washing machines. In areas where
the water hardness is soft it is not necessary to
use a water softener.
To know the water hardness in your area,
contact your local water authority.
Use the correct quantity of the water softener.
Obey the instructions that you find on the
packaging of the product.
Care and cleaning
WARNING!
Refer to Safety chapters.
External cleaning
Clean the appliance only with soap and warm
water. Fully dry all the surfaces.
CAUTION!
Do not use alcohol, solvents or
chemical products.
Descaling
If the water hardness in your area is high or
moderate, we recommend that you use a water
descaling product for washing machines.
Regularly examine the drum to prevent limescale
and rust particles.
To remove rust particles use only special
products for washing machine. Do this
separately from the laundry wash.
Always obey the instructions that
you find on the packaging of the
product.
Maintenance wash
With the low temperature programmes it is
possible that some detergent stays in the drum.
Make regularly a maintenance wash. To do this:
• Remove the laundry from the drum.
• Set the cotton programme with the highest
temperature with a small quantity of
detergent.
Door seal
Regularly examine the
seal and remove all
objects from the inner
part.
www.zanussi.com 13

Cleaning the detergent dispenser
1 2
3 4
5 6
Cleaning the inlet hose and the valve
filter
1
2
3
1 2
3
45°
20°
4
Frost precautions
If the appliance is installed in an area where the
temperature can be less than 0 °C, remove the
remaining water from the inlet hose and the
drain pump.
Do this procedure also when you
want to do the emergency drain.
1. Disconnect the mains plug from the mains
socket.
2. Remove the water inlet hose.
3. Remove the drain hose from the rear
support and unhook it from sink or spigot.
4. Put the ends of the drain and inlet hose in a
container. Let the water flow out of the
hoses.
5. When no more water flows, install the inlet
hose and the drain hose again.
WARNING!
Make sure that the temperature is
more than 0 °C before you use the
appliance again. The manufacturer is
not responsible for damages caused
by low temperatures.
Troubleshooting
WARNING!
Refer to Safety chapters.
Introduction
The start of the appliance does not occur or it
stops during operation.
First try to find a solution to the problem (refer
to the table). If not, contact the Authorised
Service Centre.
With some problems, the acoustic signals
operate. The indicator of button flashes in
red and one of the indicators comes on, to
show an alarm code:
14 www.zanussi.com

• - The appliance does not fill with water
properly.
• - The appliance does not drain the water.
• - The appliance door is open or not
closed correctly. Please check the door!
• The indicator of button flashes in red 11
times and 1 (or 2 or 3) time(s) in yellow: The
mains supply is unstable. Wait until the
mains supply is stable.
WARNING!
Deactivate the appliance before you
do the checks.
Possible failures
Problem Possible solution
The programme does not
start. • Make sure that the mains plug is connected to the mains socket.
• Make sure that the appliance door is closed.
• Make sure that there is not a damaged fuse in the fuse box.
• Make sure that the Start/Pause has been pressed.
• If the delay start is set, cancel the setting or wait for the end of count-
down.
• Deactivate the Child Lock function if it is on.
The appliance does not fill
with water properly. • Make sure that the water tap is open.
• Make sure that the pressure of the water supply is not too low. For
this information, contact your local water authority.
• Make sure that the water tap is not clogged.
• Make sure that the filter of the inlet hose and the filter of the valve are
not clogged. Refer to “Care and cleaning”.
• Make sure that the inlet hose has no kinks or bends.
• Make sure that the connection of the water inlet hose is correct.
The appliance does not drain
the water. • Make sure that the sink spigot is not clogged.
• Make sure that the drain hose has no kinks or bends.
• Make sure that the connection of the drain hose is correct.
• Set the drain option if you set a programme without drain phase.
• Set the drain option if you set an option which ends with water in the
drum.
• If above mentioned solutions do not help, contact the Authorised
Service Centre (as the filter of the drain pump may be clogged).
The spin phase does not op-
erate or the washing cycle
lasts longer than usually.
• Adjust manually the items in the tub and start the spin phase again.
This problem may be caused by balance problems.
• Set the spin option.
• Set the drain option if you set an option which ends with water in the
drum.
• If above mentioned solutions do not help, contact the Authorised
Service Centre (as the filter of the drain pump may be clogged).
There is water on the floor. • Make sure that the couplings of the water hoses are tight and there is
not water leakages.
• Make sure that the water inlet hose and the drain hose have no dam-
ages.
• Make sure you use the correct detergent and the correct quantity of
it.
www.zanussi.com 15

Problem Possible solution
You cannot open the appli-
ance door. • Make sure that the washing programme is finished.
• Set the drain or the spin option if there is water in the drum.
• Do the emergency drain procedure. See "Frost precautions" (in "Care
and Cleaning" chapter).
The appliance makes an un-
usual noise. • Make sure the levelling of the appliance is correct. Refer to 'Installa-
tion instruction'.
• Make sure that the packaging and/or the transit bolts are removed.
Refer to 'Installation instruction'.
• Add more laundry in the drum. The load may be too small.
The appliance fills with water
and drain immediately. • Make sure that the drain hose is in the correct position. The end of
the hose may be too low. Refer to 'Installation instruction'.
The washing results are not
satisfactory. • Increase the detergent quantity or use a different detergent.
• Use special products to remove the stubborn stains before you wash
the laundry.
• Make sure that you set the correct temperature.
• Decrease the laundry load.
You cannot set an option. • Make sure that you press only the wanted touch button(s).
After the check, activate the appliance. The
programme continues from the point of
interruption.
If the problem occurs again, contact the
Authorised Service Centre.
If the appliance shows other alarm codes (the
indicator of button flashes in red).
Deactivate and activate the appliance. If the
problem continues, contact the Authorised
Service Centre.
Service
We recommend the use of original spare parts.
When contacting the Authorised Service
Centre, make sure that these data are available.
You can find the information on the rating plate:
model (Mod.), PNC (Prod.No.), Serial number
(Ser.No.).
Technical Data
Dimension Width/ Height/ Depth/ Total
depth 600 mm/ 850 mm/ 600 mm/ 660 mm
Electrical connection Voltage
Overall power
Fuse
Frequency
230 V
2200 W
13 A
50 Hz
Level of protection against ingress of solid particles and
moisture ensured by the protective cover, except where the
low voltage equipment has no protection against moisture
IPX4
Water supply pressure Minimum
Maximum 0,5 bar (0,05 MPa) 8 bar (0,8 MPa)
Water supply 1) Cold water
16 www.zanussi.com

Maximum Load Cotton 9 kg
Energy Efficiency Class A+++
Spin Speed Maximum 1200 rpm
1) Connect the water inlet hose to a water tap with a 3/4'' thread.
CH
Garantie, Garanzia, Guarantee
Kundendienst, service-clientèle, Servizio
clienti, Customer Service Centres
Servicestellen Points de Service Servizio dopo ven-
dita Point of Service
5506 Mägenwil/Zürich
Industriestrasse 10 3018 Bern Morgen- strasse 131 1028 Préverenges Le Trési 6 6928 Manno Via Violino 11
9000 St. Gallen Zürch-
erstrasse 204e
4052 Basel St. Jakob-
Turm Birsstrasse 320B
6020 Emmenbrücke
Seetalstrasse 11
7000 Chur Comercial-
strasse 19
Ersatzteilverkauf/Points de vente de
rechange/Vendita pezzi di ricambio/spare
parts service: 5506 Mägenwil,
Industriestrasse 10, Tel. [phone]
Fachberatung/Verkauf/Demonstration/
Vente/Consulente (cucina)/Vendita 8048
Zürich, Badenerstrasse 587, Tel. [phone]
11
Garantie Für jedes Produkt gewähren wir ab
Verkauf bzw. Lieferdatum an den
Endverbraucher eine Garantie von 2 Jahren.
(Ausweis durch Garantieschein, Faktura oder
Verkaufsbeleg). Die Garantieleistung umfasst
die Kosten für Material, Arbeits- und Reisezeit.
Die Garantieleistung entfällt bei Nichtbeachtung
der Gebrauchsanweisung und Betriebs-
vorschriften, unsachgerechter Installation, sowie
bei Beschädigung durch äussere Einflüsse,
höhere Gewalt, Eingriffe Dritter und
Verwendung von Nicht-Original Teilen.
Garantie Nous octroyons sur chaque produit 2
ans de garantie à partir de la date de livraison
ou de la mise en service au consommateur
(documenté au moyen d’une facture, d’un bon
de garantie ou d’un justificatif d’achat). Notre
garantie couvre les frais de mains d’œuvres et
de déplacement, ainsi que les pièces de
rechange. Les conditions de garantie ne sont
pas valables en cas d’intervention d’un tiers non
autorisé, de l’emploi de pièces de rechange non
originales, d’erreurs de maniement ou
d’installation dues à l’inobser-vation du mode
d’emploi, et pour des dommages causés par
des influences extérieures ou de force majeure.
Garanzia Per ogni prodotto concediamo una
garanzia di 2 anni a partire dalla data di
consegna o dalla sua messa in funzione. (fa
stato la data della fattura, del certificato di
garanzia o dello scontrino d’acquisto) Nella
garanzia sono comprese le spese di
manodopera, di viaggio e del materiale. Dalla
copertura sono esclusi il logoramento ed i danni
causati da agenti esterni, intervento di terzi,
utilizzo di ricambi non originali o dalla
www.zanussi.com 17

inosservanza delle prescrizioni d’istallazione ed
istruzioni per l’uso.
Warranty For each product we provide a two-
year guarantee from the date of purchase or
delivery to the consumer (with a guarantee
certificate, invoice or sales receipt serving as
proof). The guarantee covers the costs of
materials, labour and travel. The guarantee will
lapse if the operating instructions and
conditions of use are not adhered to, if the
product is incorrectly installed, or in the event of
damage caused by external influences, force
majeure, intervention by third parties or the use
of non-genuine components.
ENVIRONMENTAL CONCERNS
Recycle the materials with the symbol . Put
the packaging in applicable containers to
recycle it. Help protect the environment and
human health and to recycle waste of electrical
and electronic appliances. Do not dispose
appliances marked with the symbol with the
household waste. Return the product to your
local recycling facility or contact your municipal
office.
18 www.zanussi.com

Inhaltsverzeichnis
Sicherheitsinformationen 19
Sicherheitsanweisungen 20
Gerätebeschreibung 22
Bedienfeldbeschreibung 22
Programmübersicht 23
Verbrauchswerte 24
Optionen 25
Einstellungen 26
Reinigen Sie vor dem ersten Gebrauch 27
Täglicher Gebrauch 27
Tipps und Hinweise 30
Reinigung und Pflege 31
Fehlersuche 33
Technische Daten 35
Garantie, Garanzia, Guarantee 36
Änderungen vorbehalten.
Sicherheitsinformationen
Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst
die Gebrauchsanleitung. Der Hersteller übernimmt keine
Verantwortung für Verletzungen und Beschädigungen durch
unsachgemäße Montage. Bewahren Sie die Gebrauchsanleitung
griffbereit auf.
Sicherheit von Kindern und schutzbedürftigen
Personen
•Das Gerät kann von Kindern ab 8 Jahren und Personen mit
eingeschränkten physischen, sensorischen oder geistigen
Fähigkeiten oder mit mangelnder Erfahrung und/oder
mangelndem Wissen nur dann verwendet werden, wenn sie
durch eine für ihre Sicherheit zuständige Person beaufsichtigt
werden oder in die sichere Verwendung des Geräts
eingewiesen wurden und die mit dem Gerät verbundenen
Gefahren verstanden haben.
•Kinder dürfen nicht mit dem Gerät spielen.
•Alle Verpackungsmaterialien von Kindern fernhalten.
•Alle Reinigungsmittel von Kindern fernhalten.
•Halten Sie Kinder und Haustiere vom geöffneten Gerät fern.
•Wartung oder Reinigung des Geräts dürfen nicht von Kindern
ohne Aufsicht erfolgen.
Allgemeine Sicherheit
•Nehmen Sie keine technischen Änderungen am Gerät vor.
www.zanussi.com 19

•Beachten Sie die maximale Beladungsmenge von 9 kg (siehe
Kapitel „Programmtabelle“).
•Der Betriebswasserdruck (Mindest- und Höchstdruck) muss
zwischen 0,5 bar (0,05 MPa) und 8 bar (0,8 MPa) liegen.
•Die Lüftungsöffnungen im Gerätesockel (falls vorhanden)
dürfen nicht von einem Teppichboden blockiert werden.
•Das Gerät muss mit den mitgelieferten neuen Schläuchen an
die Wasserversorgung angeschlossen werden. Alte Schläuche
dürfen nicht wieder verwendet werden.
•Wenn das Netzkabel beschädigt ist, muss es vom Hersteller,
seinem autorisierten Kundenservice oder einer gleichermaßen
qualifizierten Person ausgetauscht werden, um
Gefahrenquellen zu vermeiden.
•Schalten Sie das Gerät immer aus und ziehen Sie den
Netzstecker aus der Steckdose, bevor Reinigungsarbeiten
durchgeführt werden.
•Reinigen Sie das Gerät nicht mit einem Wasser- oder
Dampfstrahl.
•Reinigen Sie das Gerät mit einem weichen, feuchten Tuch.
Verwenden Sie ausschließlich Neutralreiniger. Benutzen Sie
keine Scheuermittel, scheuernde Reinigungsschwämmchen,
Lösungsmittel oder Metallgegenstände.
Sicherheitsanweisungen
Montage
• Entfernen Sie die Verpackungsmaterialien
und die Transportschrauben.
• Bewahren Sie die Transportschrauben auf.
Wenn Sie das Gerät umsetzen, müssen Sie
die Trommel blockieren.
• Seien Sie beim Umsetzen des Geräts
vorsichtig, denn es ist schwer. Tragen Sie
stets Sicherheitshandschuhe.
• Stellen Sie ein beschädigtes Gerät nicht auf
und benutzen Sie es nicht.
• Halten Sie sich an die mitgelieferte
Montageanleitung.
• Stellen Sie das Gerät nicht an einem Ort auf,
an dem die Temperatur unter 0 °C absinken
kann oder an dem es Witterungseinflüssen
frei ausgesetzt ist.
• Stellen Sie sicher, dass der Boden, auf dem
das Gerät aufgestellt wird, eben,
hitzebeständig und sauber ist.
• Stellen Sie das Gerät nicht an einem Ort auf,
an dem die Tür nicht vollständig geöffnet
werden kann.
• Stellen Sie sicher, dass die Luft zwischen
Gerät und Boden zirkulieren kann.
• Stellen Sie die Füße so ein, dass der dazu
erforderliche Abstand zwischen Gerät und
Boden vorhanden ist.
• Stellen Sie das Gerät nicht an einem Ort auf,
an dem die Tür nicht vollständig geöffnet
werden kann.
Elektrische Anschlüsse
• Das Gerät muss geerdet sein.
20 www.zanussi.com