Zebora YSW 10 User manual

Zebora YSW 10 Wireless Camera
Quick Setup Guide
1
Email: [e-mail]

2
Cellphone/Tablet Setup
1. Make sure your cellphone/tablet is connected with Wi-Fi.
2. Search “Yoosee” App from Apple Store (for iOS user) or Play Store
(for Android user) and install in your cellphone/tablet. Register an
account and log in. (Other android users, just go to www.zeboragroup.com
“Download Center ” to download the “software for android”)
3. On the top right corner, click “+” and choose “Smartlink”. Now plug in
your camera and wait for 20 sec until you hear “Di-Di-” from the
camera (Must hear the voice before next step). Click “Next”.
4. Manually input the Wi-Fi password correctly (*in case, if you choose
the default wireless password, make sure to delete an empty space at
the end). Click “Next”.
5. You will hear “Ding” once the camera detects the Wi-Fi. About 25 sec,
“Setting Success” pops up. Click “Ok”, and camera ID pops up.
6. Please input camera password “123”. Click “Save”. Your camera now is
connected to Wi-Fi. Click image icon to play video. Swipe the screen to
control the camera remotely.
**If the Wi-Fi connection failed, reset the camera: press the reset button
for 5 sec. After 30 sec, you will hear “Di-Di-”, then repeat step 3 to 6.
*Must be the �irst step to connect the camera with Wi-Fi.

3
Add an Online Camera
1. Add an online camera to a second device: you must register another
Yoosee account. Make sure one Yoosee account is for one device only.
Log in Yoosee account:
* If the device connects with the same Wi-Fi as the camera. “Discover 1
new device” pops up, click it and input the camera password (If you
don’t reset password, it is “123”). Click “Save” to add the camera to your
Yoosee device list.
* If your device does not connect with the same Wi-Fi as the camera. You
can click “+” on the top right corner, choose “Manual” to add the camera.
Input a camera name, the camera ID(located at the bottom) and camera
password
. Click “Save” to add the camera to device list.
2. Your camera is online, but you delete the APP or the camera from
your Yoosee account.
Two conditions to add an online camera:
How to add an online camera

1. Go to www.zeboragroup.com, in “Download Center>>App Download”,
download CMS for Windows PC (Not Mac) and intall it. Click “CMSClient”
icon on your desktop.
2. You can choose one of the two Login types:
*Remote Login: use your cellphone/tablet Yoosee account (recom’d)
*Local Login: User: admin (case sensitive)
Password: 00000000 (Eight “0”)
3. After log in, click on the left to add device, then input your camera
ID next to the 3C ID. The camera ID is located at the bottom of the
camera (7 digits). Input your camera password (If you don’t reset the
password, it is “123”). Change the device name (Optional). Click “OK”.
4. Double click the device name under the device list on the left panel to
start or stop connecting to your camera. Click the four arrow panel on
the left to control the camera.
*If you cannot connect your camera in current login mode, just log out
and choose another login type.
5. There are multiple monitor screens. One screen is for one camera.
Double click to get full screen, and double click again to return. 4
PC (Windows only) Setup
*You can only set up the PC after your camera is connected to Wi-Fi.

5
Video Record Setup
For Cellphone/Tablet
*You need to have a micro SD card, it supports up to 64GB.
1. Insert the SD card into the slot behind the camera.
2. Open “Yoosee”, click the camera name, and “ Playback, Settings, Edit ”
pops up:
3. Click “Settings” >>Date and Time. Set the camera “date and time”
to your local date and time, click “Apply”; Set the “Timezone” to your
local timezone (refer to Page 9), click “Apply”. Go to “Storage info”
to “Format/Erase SD card”.
4. Remove the SD card and insert again (Very important step).
5. Click “Settings”>>Record Settings”, turn on “Record Switch”.
6. Click “Playback”, you can play the recorded videos after 30~60 min
(Video will be saved automatically in “Playback” every 30 min).
For PC
*No micro SD card needed for recording.
1. Log in CMSClient, click and change the “File Save Path” for video
recorded. Find the �ile where you saved the videos and play.
2. On the top panel of the video screen, you can choose the icon
for “talking, recording, snapshot” (from left to right).

6
Motion Detection Setup
Click “Settings”. Turn on “Receive Alarm” and “Motion Detection”. If you
need camera alarm, turn on “Buzzer”. Go back to device list, click and
switch to . Now motion detection has already set up.
* alarm; disalarm.
Go to Settings >> Security Settings>>Admin Password to set up a new
password for your camera (Highly recommend)
In your real-time video streaming, you will see the lower banner
*Press and hold for talking
Open “Yoosee”, click camera name, “Playback, Settings, Edit” pops up:
Two-way audio
Camera Password Change Setup

1. Make sure your cellphone/tablet is connected with Wi-Fi.
2. Search “Yoosee” App from Apple Store (for iOS user) or Play Store
(for Android user) and install in your cellphone/tablet. Register an
account and log in. (Other android users, just go to www.zeboragroup.com
“Download Center ” to download the “software for android”)
3. On the top right corner, click “+” and choose “Smartlink”. Now plug in
your camera and wait for 20 sec until you hear “Di-Di-” from the
camera (Must hear the voice before next step). Click “Next”.
4. Manually input the Wi-Fi password correctly (*in case, if you choose
the default wireless password, make sure to delete an empty space at
the end). Click “Next”.
5. You will hear “Ding” once the camera detects the Wi-Fi. About 25 sec,
“Setting Success” pops up. Click “Ok”, and camera ID pops up.
6. Please input camera password “123”. Click “Save”. Your camera now is
connected to Wi-Fi. Click image icon to play video. Swipe the screen to
control the camera remotely.
**If the Wi-Fi connection failed, reset the camera: press the reset button
for 5 sec. After 30 sec, you will hear “Di-Di-”, then repeat step 3 to 6.
Troubleshootings
Q: why it shows “of�line” when I open the App?
A: 1. Check if your camera is plugged in or Wi-Fi is connected .
2. Pull the “device list” page and hold for seconds to re�lesh the page.
3. Delete the camera, and manually add the camera again.
Q: Why I cannot connect the camera to Wi-Fi in camera setup?
A: 1. Make sure you input the correct wireless password;
2. Check if your router is 2.4 GHz but not 5.0 GHz, this device only
supports 2.4 GHz. If your router is 2.4 GHz and 5.0 GHz swichable,
contact your router carrier to turn off 5.0 GHz.
3. Make sure you start to connect Wi-Fi during the beep “Di-Di-”;
4. If the above steps still don’t work, please reset and reconnect your
camera. Please also refer to Page 2 of Wi-Fi connection.
Q: After connect with my second cellphone to the camera, why does one
of the cellphones show “of�line”, or “ID busy”?
A: Both of the cellphones may share the same account to login, make
sure one cellphone/tablet should use one account. Please go to
Account Login page to register a new account. If you see “error 6”
during registration, it means that the account has been taken.
Part 1: About Network Connection
7

Q: There is a red exclamation mark , I cannot connect to camera.
A: Click the icon, if it becomes , then you can connect to the camera.
But if it shows Device password error, click camera name and choose
“Edit”, input the correct camera password (If you don’t reset password,
it is “123”); if it shows Network error, reset your router. (When you see
Network error, it is because too many wireless networks interfere while
lots of devices are using the Wi-Fi. The wireless may exist around your
area.)
Part 2: About SD Card Video Recording
Q: I format the SD card, why I cannot turn on “Record Switch”?
A: 1. Format the SD card on cellphone/tablet Yoosee (Settings>>Storage info
>>format/erase SD card). Make sure SD Remainder Capacity is not “zero”.
2. You should remove the SD card and insert again. The record light
should be on before you turn on the “Record Switch”. (if you still cannot
turn on “record switch”, just eject and insert the card again).
3. or you can keep the card in the slot, but unplug the camera and plug in
again. Then you can turn on “Record Switch”.
8

Time zone in US &CAN UTC Offset UTC Offset
(Standard Time) (Daylight Saving Time)
Newfoundland (NST) UTC-3 UTC-2
Atlantic (AST) UTC-4 UTC-3
Eastern (EST) UTC-5 UTC-4
Central (CST) UTC-6 UTC-5
Mountain (MST) UTC-7 UTC-6 (*N/A for AZ)
Paci�ic (PST) UTC-8 UTC-7
Alaskan (AKST) UTC-9 UTC-8
Hawaii-Aleutian (HST) UTC-10 UTC-9
Samoa (SST) UTC-11 UTC-11
Chamorrow (ChST) UTC+10 UTC+10
Time zone in EU UTC+1 UTC+2
A: You should Set the camera time to your local time/date and
zone (Setting >> Date and Time Settings). This will help you
capture the video synchronously when you record videos. Here
is Timezone for your reference.
Q: Why I cannot �ind the recorded video in “Playback”?
9

Part 3: About PC Settings
10
Q: How can I delete the video if the SD card is full？
A: The SD card can be overwritten if it is full. You can also delete it
manually. Turn off the “Record Switch” in “Record Settings”, then go to
“Storage info” to “formart/erase SD card”.
Q: Can I play the video in SD card (in camera) through CMSClient on PC ?
A: Yes. Log in CMSClient using remote login mode. Click the “Playback”
icon. In “Record �ile type”, choose “remote record �ile”. Select the camera
where your SD card locates in. Input the begin and end recording time.
Then click “Search”, and you can view the SD card records.
Q: The camera stops recording, and I can’t format the SD card either on
Yoosee or computer, why?
A: It is probably that your SD card is defective.
Q: My SD card is in the slot, why I cannot open “Storage info”?
A: Eject the SD card and insert again.
Q: I can log in CMSClient on PC, but I cannot connect to the camera.
A: 1. Make sure that you input the correct camera password.
2. If you cannot connect the camera, just select another login mode to
add your camera.

Q: Why can’t I change camera settings？
A: Because your “Yoosee” is not connected with the camera. Only when the
communication of camera and Yoosee is in good condition, you can
change the camera settings. Please pull the page of device list to refresh.
Q: Why the camra is video recording when I start monitoring on CMS?
A: Just click , and select “Close” for Auto start record when monitoring.
Part 4: About Camera Settings
Q: How can I change the camera password？
A: You can change it in “Settings>>Security Settings>>Admin password”.
You can also set a guest password, so that people can use this password
to add your camera to view the video, but they can’t change the camera
settings.
Q: How can I side up the image if I install the camera on ceiling?
A: Just click “Settings>>Media Settings”, turn on “Images Reverse”.
11

About Zebora
Zebora Group Corp headquaters in Boston, MA. It is a growing company with
a US registered trademark by the United States Patent and Trademark Of�ice
(USPTO). Zebora focuses on providing state-of-the-art household smart
products that are company branded. Our aim is to make your life easier and
more intelligent.
The focus of Zebora Group is to create and develop up-to-date intelligent
products for every day uses. We have currently produced a series of high
resolution surveillance cameras such as YSW15 (ZQF510), YSW8, and YSW10.
In the Zebora community, our customer service and technical support team
will always be there for you. We promise, all the cameras you ordered from
Zebora are one year warranty! Your satisfaction and the high quality of our
products is our No. 1 priority. Zebora Group provides people and products
you can count on!
contact us:
Email: [e-mail]
Phone: [phone] (US, EST 10AM-6PM)
Website: www.zeboragroup.com
12