ZEIA PHANTOM FX-61 User manual

All instructions, warranties and other collateral documents are subject to change at the sole discretion of our company. For up-to-date product literature,
Visit our website and click on the support tab for this product'
wARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product
can result ¡n damage to the product, personal property and cause serious injury'
This is a sophisticated hobby product. lt must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate
this product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use
by children without direct adutt supervision. Do not attempt disassembly, use with incompatible components or augment product in any way w¡thout the
approval of our company. This manual contains instructions for safety, operation and maintenance. lt is essential to read and follow all the instructions
and warntngs in the manual, prior to assembly, setup or use, in order to operate Correctly and avoid damage or serious injury'
Additional Safety Precautions and Warnings
As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage to the
product or the property of others.
Age Recommendation: Not for children under 14 years. This is not a toy.
. This model is controlled by a radio signal subject to interference from many sources outside your control. lnterference can cause momentary loss of
control, so ¡t is advisable to always keep a safe distance in all directions around your mode as this margin will help avoid collisions or injury'
. Always operate your model in open Spaces away from full-size vehicles, traffic and people.
. Always carefully follow the directions and warnings for this and any optional support equipment (chargers, rechargeable battery, package, etc )
.Alwayskeepallchemicals,smallpartsandanythingelectricaloutofthereachofchildren
. Always avoid water exposure to all equipment not specifically designed and protected for this purpose. Moisture causes damage to electronics'
. Never place any portion of the model in your mouth as it could cause serious iniury or even death.
. Never operate your model with low transmitter batteries'
The Battery charger included with your aircraft is designed to safely charge the Li-Po battery.
CAUTION: All instructions and warnings must be followed exacfly. Mishandling of Li-Po batteries can result in a fire, personal injury, and/or property damage'
. By handl¡ng, charging or using the included Li-Po battery you assume all
risks associated with lithium batter¡es.
. lf at any time the battery begins to balloon or swell, discontinue the use of
immediately.
. Always store the battery at room temperature in a dry area for best results'
. Always fansport or temporarily store the battery in a temperature range of
4O-120o F. Do not store battery or model in a car or direct sunlight lf stored
in a hot car, the battery can be damaged or even catch fire'
. NEVER USE A Ni-Cd OR N|-MH CHARGER. Failure to charge the batte-
ry with a compatibte charger may cause fire resulting in personal injury
and/or property damage.
. Never discharge Li-Po cells to below 3.7V under load
. Never cover warning labels with hook and loop strips.
. Never leave charging batteries unattended.
. Never charge batteries outside safe temperature range
. Never charge damaged batteries.
#
# 121104

1.1 Main wings assemblY
,.'\.:x-
Glue the plastic part G1 in the wings' leading edge
lnstall the fiberglass tube & plastic locker L'1 in
the left & right wing panels'(As shown)
Glue the big fiberglas tube on the fuselage and center it'
{Attention: Make the two ends of fiberglass tt¡be outside the fuselage 23'24mm }
1.3 Fix and remave main w¡ngs
Connet the wings to the fuselage(inset the small tube into the big
Use a screw driver to lock L1 anO tft" slices on the wing and body
are closely connected to the fuselage'
one.)
uu .ho*n in the picture to make the wings
1.2 Fuselage assernblY

Congratulations on purchasing this RC airplane. To ensure your full enjoyment, please check the spare parts
prior to assembly.
61 in(1550mm)
-T'
E
E
@
@
._c
o
oq
@
N
I
4ch transmitter(delta mix)
KV900 Brushless motor
9x6 propeller
9gram seryo * 2
3OA ESC
35 l1 .1V 5300rnAh Lipo battery
Plug-N.Play Ready to Fly
Need to
Complete
Need to
Complete
Need to
Complete
Need to
Gomplete
Need to
Complete
Need to
Complete
lncluded
Need to
Complete
Need to
Complete
Need to
Complete
K^@-
+
@
fl
900kv brushless outrunner
motor
304 brushless ESC
(2) 99ram Servos
Recommended Receiver:
4 channels 2.4GHz
Baftery: 11.1V 5.3Ah 10C Lipo battery
Charger: 1.0A, 2-3 cell balance charger
Recommended Transmitter:
4 channels 2.4GHz(delta mix.)
Cre.
\\it#/
# 121104

1.1 Wings assembly
A Stick the glass fiber tube in the wing panel (glue) and slide it
through the fuselage. Then, glue another wing panel to the
fuselage.
1.2 Aileron servo
Glue the servo in the wing with the servo arm aligned
with the control horn.
1.3 Motor assembly
A Glue the plastic motor mount M1 on the fuselage as dep¡cted
(Pay attention to the top and bottom of motor mount).
/l
lt
,l
Connect the linkage between the servo and control horn
# 121104
Glue the foam motor cover.

Glue the tail fins on the wing.
1.5 Propeller
1.4 Tail fins & canopy
1.6 Cable connection
IESC
Servo2
Servo1
Black line
Red line
A GIue the plastic lock C1 and Stick C2.
I lnstall the propeller on the motor shaft with 01
Servos and ESC Cables
# 121104
White:üne

2.1 Installing battery
A Turn on the transmitter.(Notice: Put the throttle stick and
trim in the lowest location and center other trims) A lnstall the battery in the fuselage and complete the connection.
2.3 Control Direction Test
Move the controls on the transmitter to make sure the aircraft control surfaces move correctly. After doing the Control Test, correctly set
the failsafe. Make sure the transmitter controls are at neutral and the throttle and throttle trim are in the low position.
L Notice: Turn on the delta mixer switch.
TIP: If you want to fix the clevis tightly.
€D
Adjust the linkage as below: 1
+-u
" ""----_,
# 121104

éa -i\
W A
Stick Down
tt
ffi :
t.!r..a tt lr
\i_y {Z
Stick Up
++
Forthefirsttryorbeginners,pleaseadjustcontrolthrowaccordingtotn"|@
2.5 Center of Gravity(CG)
2.4 Adjust Control throw
# 121104
Moving the pushrod inward decreases the control throw
Moving the pushrod outward increases the control throw
Moving the pushrod outward decreases the control throw
Moving the pushrod inward increases the control throw