360 Vision Centurion Hybrid Instruction sheet

Centurion Hybrid Installation Manual V2.1.21 Page 1
© 360 Vision Technology Ltd.
Centurion Hybrid
(Analogue & HD/IP)
Installation/Conguration Manual
The Centurion Hybrid camera is shipped from 360 Vision Technology in analogue mode.
When in analogue mode. Please note: No IP Video.
When in IP mode. Please note: No analogue Video.

Centurion Hybrid Installation Manual V2.1.21 Page 2
© 360 Vision Technology Ltd.
Table of Contents
1 Safety and Precautions .............................................................................................................................. 3
2 Housing Dimensional Drawing ................................................................................................................... 3
3 Bracket Dimensional Drawing .................................................................................................................... 4
4 Connections ............................................................................................................................................... 6
5 Connections to Centurions with HMA......................................................................................................... 7
6 Basic Twisted Pair/RS485 Data Wiring .................................................................................................... 10
7 Centurion Protocol/Address setup............................................................................................................ 10
8 Centurion OSD .........................................................................................................................................11
8.1 PIN Number ......................................................................................................................................11
9 OSD Operation/Navigation....................................................................................................................... 12
10 PSU Enclosure....................................................................................................................................... 16
11 Locating the Centurion Hybrid on your Network..................................................................................... 18
12 Connecting to the Centurion Hybrid ....................................................................................................... 18
12.1 Live View........................................................................................................................................ 20
12.1.1 Live Video .............................................................................................................................. 20
12.1.2 Status..................................................................................................................................... 21
12.2 Settings .......................................................................................................................................... 22
12.2.1 Video ...................................................................................................................................... 22
12.2.2 Video Advanced ..................................................................................................................... 23
12.2.3 Advanced Features ................................................................................................................ 24
12.2.4 Camera .................................................................................................................................. 26
12.2.5 Date/Time............................................................................................................................... 28
12.2.6 Network.................................................................................................................................. 29
12.2.7 Interfaces ............................................................................................................................... 30
12.3 Add/Edit Users ............................................................................................................................... 32
12.4 Maintenance................................................................................................................................... 33
12.5 Browser .......................................................................................................................................... 34
13 Network Settings Recovery.................................................................................................................... 35
14 Special Presets ...................................................................................................................................... 36
15 Important - Care of Painted Surfaces..................................................................................................... 36
16 Storage and Handling............................................................................................................................. 37
17 Warranty................................................................................................................................................. 37
18 PSU Enclosure....................................................................................................................................... 37
19 1080p Stream Resolutions & RTSP Links.............................................................................................. 38
20 720p Stream Resolutions & RTSP Links................................................................................................ 39
21 White Balance and Fast Shutter options................................................................................................ 39

Centurion Hybrid Installation Manual V2.1.21 Page 3
© 360 Vision Technology Ltd.
1 Safety and Precautions
1. Please read these notes before attempting to operate the 360 Vision Centurion Hybrid, and keep for future
reference.
2. DO NOT disassemble or remove covers. This will break the water seals and invalidate the warranty.
3. All servicing and repairs must be handled by 360 Vision Technology.
4. Avoid pointing the camera directly towards a bright light source (sunlight), or expose the camera to intensive
light situations as this may damage the camera pick-up device.
5. Installation should be carried out by suitably qualied personnel, in accordance with local codes of practice
and regulations.
6. 360 Vision Technology Limited accept no liability for any damage caused by incorrect or improper installation.
7. To prevent risk of injury caused by the Centurion Hybrid or mounting options becoming detached, t a
suitable safety chain or lanyard.
8. Use only 360 Vision Centurion Hybrid power supplies. These have suitable terminals for all the wires in the
Centurion composite cable.
9. Please handle the Centurion Hybrid with care, as improper handling may cause damage within this unit.
2 Housing Dimensional Drawing
Centurion HMA with LED Array
MUST NOT BE REPRODUCED OR SHOWN TO
DO NOT SCALE
ALL DIMENSIONS IN MM
REMOVE ALL SHARP EDGES
SHEET:
D
C
B
A
D
C
B
A
4
3
2
1
4
3
2
1
A3
DESCRIPTION SCALE:
PERMISSION OF THE AUTHOR.
ANY THIRD PARTY WITHOUT THE DIRECT WRITTEN
C COPYRIGHT PROTECTED AND
THIS DRAWING AND ALL COPIES ARE
PART NUMBER:
1.000 7 OF 8
TOLERANCES:-
X = 0.5
X.X = 0.1
X.XX = 0.05
A3
3rd ANGLE PROJECTION
360 Vision Technology Ltd.
Unit 7, Seymour Court,
Manor Park, Runcorn, Cheshire,
WA7 1SY. United Kingdom.
www.360visiontechnology.com
260
TILT
SWEEP
R411
497
457
125
MOUNTING BASE
10 (x4)
ON 101.6 (4 INCH) PCD
237
338 PAN SWEEP
46018
100
NAME:
M3100-D
CENTURION ASSEMBLY
ISS DATE REFERENCE
D 161115 SHEET ADDED
161115
DATE :
K.CRAIK
RELEASED:
APPROVED:
ENGINEER:
MATERIAL: FINISH:
HMA WITH LIGHTS
SCALE 0.300
M20 CABLE GLAND
(NOT SUPPLIED)
MOUNTING
BASE
M20 BLANKING
PLUG (SUPPLIED)
(x3) M8x25 HEX BOLT
M8 SPRING WASHER
M8 PLAIN WASHER
M8 FIBRE WASHER
(SUPPLIED)
SCALE 0.300
Weight 9kg

Centurion Hybrid Installation Manual V2.1.21 Page 4
© 360 Vision Technology Ltd.
3 Bracket Dimensional Drawing
Weight 1.2kg
Centurion Wall Bracket
Weight 2.2kg
Centurion Corner Bracket
Centurion PMA Bracket
Weight 1kg
MUST NOT BE REPRODUCED OR SHOWN TO
DO NOT SCALE
ALL DIMENSIONS IN MM
REMOVE ALL SHARP EDGES
SHEET:
D
C
B
A
D
C
B
A
4
3
2
1
4
3
2
1
A3
DESCRIPTION SCALE:
PERMISSION OF THE AUTHOR.
ANY THIRD PARTY WITHOUT THE DIRECT WRITTEN
C COPYRIGHT PROTECTED AND
THIS DRAWING AND ALL COPIES ARE
PART NUMBER:
0.125 9 OF 9
TOLERANCES:-
X = 0.5
X.X = 0.1
X.XX = 0.05
A3
3rd ANGLE PROJECTION
360 Vision Technology Ltd.
Unit 7, Seymour Court,
Manor Park, Runcorn, Cheshire,
WA7 1SY. United Kingdom.
www.360visiontechnology.com
125
OUTSIDE
DIAMETER
9 (x4) ON
101.6 (4 INCH) PCD
USE M8 BOLT FOR
FIXING TO POLE
60
M8 (x4) ON 101.6
(4 INCH) PCD.
FIX PREDATOR USING:
M8x30 HEX-HEAD BOLTS (x4)
- STAINLESS STEEL.
M8 SPRING LOCK WASHER (x4)
- STAINLESS STEEL.
73
M20x1.5P
M20x1.5P
73
M20x1.5P
8.0 (x4) ON 101.6
(4 INCH) PCD.
FIX PREDATOR USING:
M8x30 HEX-HEAD BOLTS (x4)
- STAINLESS STEEL.
M8 SPRING LOCK WASHER (x4)
- STAINLESS STEEL.
53.0
125
OUTSIDE
DIAMETER
M20x1.5P
10 (x4) ON
101.6 (4 INCH) PCD
USE M8 BOLT FOR
FIXING TO POLE
NAME:
M5350-A
PREDATOR ASSEMBLY
STAINLESS STEEL
ISS DATE REFERENCE
A 290216 FIRST ISSUE
290216
DATE :
K.CRAIK
RELEASED:
APPROVED:
ENGINEER:
-- MATERIAL: FINISH:
MOUNT PREDATOR
TO THIS FACE.
MOUNT POLE
TO THIS FACE.
MOUNT PREDATOR
TO THIS FACE.
MOUNT POLE
TO THIS FACE.
MATERIAL:
STAINLESS STEEL
MASS = 3.6 Kg PMA = STAINLESS STEEL
SCALE 0.5
SCALE 0.5
PMA = ALUMINIUM
MATERIAL:
ALUMINIUM
MASS = 0.93Kg
SCALE 0.5 SCALE 0.5

Centurion Hybrid Installation Manual V2.1.21 Page 5
© 360 Vision Technology Ltd.
Weight 2.5kg
Centurion PMB Bracket

Centurion Hybrid Installation Manual V2.1.21 Page 6
© 360 Vision Technology Ltd.
4 Connections
MAINS FUSE
CENTHYB-PSU-SM
MAINS FUSE 3 = 2AF
OUTPUT FUSE
CENTHYB-PSU-SM
FUSE 1 = 6.3AT
FUSE 2 = 1AT
FUSE 4 = N/A
MAINS input
100 - 240Vac
Io Vo
Adj Adj
Model Number: CENTHYB-PSU-SM Serial Number: yymmndd-xxxx Input Voltage:100-240VAC 50/60Hz Input current: 2.1A Output Voltage: 30V DC Output Current: 6.2A
24Vac(-)
24Vac(-)
24Vac(+)
CENTHYB-PSU-SM
255 x 180 x 100mm
Enclosure Dimensions
N/A
From Camera
(Optional)
To Analogue
Controller
(Optional)
360
USE
24Vac(-)
Coax Core
Coax Screen
RS485 D+
RS485 D-
To Camera

Centurion Hybrid Installation Manual V2.1.21 Page 7
© 360 Vision Technology Ltd.
5 Connections to Centurions with HMA
When the HMA (Hinged Mount Adaptor) is tted to the Centurion Hybrid, the ‘Centurion Composite Cable’ is not
used. Connections between the power supply and Centurion use conventional cables as detailed below.
24Vac Power connections between Centurion PSU and Centurion that is tted with HMA
Cable Size No IR IR80 IR110WL
0.75mm² 20m 10m 7.5m
1.00mm² 25m 12.5m 10m
1.25mm² 30m 15m 12.5m
1.50mm² 40m 20m 15m
2.50mm² 65m 30m 25m
3.00mm² 80m 40m 30m
4.00mm² 100m 50m 40m
Ethernet connections between Centurion PSU and Centurion that is tted with HMA.
The Ethernet connection uses standard CAT5, CAT5e or CAT6 cables tted with RJ45 connectors.
Gain access to connectors in the HMA
• Ensure that the xed part of the HMA is securely bolted to the top of the pole.
• The hinged part of the HMA (Hinged Mount Adapter) is fastened to the xed part using three M8x25
long hex head bolts. Use a spanner (13mm) to remove the three bolts. Each bolt is tted with a
split spring lock washer, a plain metal washer (which prevents the split washer from damaging the
bre washer) and a bre washer (which prevents the paint on the hinged part from being damaged
unnecessarily.
• Open the hinge taking care that the gasket is not damaged and support the weight of the Centurion.
Gently open the HMA until the lanyard is able to take the weight. If the lanyard appears to support the
weight of the Centurion, there is no need to continue to support the Centurion. The connection circuit
board (PCB-000-0222-xx) can now be seen.
RJ45 CAT5, CAT5e, CAT6 Cable Signal
Pin 1 White with Orange Band Tx+
Pin 2 Orange Tx-
Pin 3 White with Green Band Rx+
Pin 4 Blue
Pin 5 White with Blue Band
Pin 6 Green Rx-
Pin 7 White with Brown Band
Pin 8 Brown

Centurion Hybrid Installation Manual V2.1.21 Page 8
© 360 Vision Technology Ltd.
Analogue Camera output
Use BNC 1 for the analogue camera output.
Power Connections
Connect 24Vac to CON5.
Ethernet Connections
Connect Ethernet cable to HD HMA Centurion connection
board using a RJ45 connector (CON4).
RS485 Connection
Use CON7 to connect the RS485 twisted pair data to the
Centurion Hybrid..
Please make sure there is adequate spare cable for when the camera is resting on the lanyard, failure to do this
could damage the connector circuit board.

Centurion Hybrid Installation Manual V2.1.21 Page 9
© 360 Vision Technology Ltd.
Centurion Hybrid
Analogue
Installation/Conguration Section

Centurion Hybrid Installation Manual V2.1.21 Page 10
© 360 Vision Technology Ltd.
6 Basic Twisted Pair/RS485 Data Wiring
The Centurion is capable of being controlled by either Coax Telemetry or Twisted Pair Telemetry (RS485).
Below are wiring congurations for two wiring formats used for Twisted Pair Telemetry (RS485). The Centurion
camera cannot be wired in a Daisy Chain conguration as the RS485/twisted pair circuit is terminated/end of
line.
Daisy Chain (Cannot be used with the 360 Centurion)
RS485 twisted pair cable is wired to each camera in a “chain”. Only the
last camera is to have the RS485 (end of line) termination on, all other
cameras in the chain must have the RS485 termination o󰀨.
Star Wired
RS485 twisted pair cable is wired to each camera in a “star” from one
point. A suitable RS485 star driver/data distribution product must be
used. All cameras in this wiring conguration must have the RS485
(end of line) termination on.
7 Centurion Protocol/Address setup.
All Centurion cameras are supplied set to 360 Vision protocol, camera twisted pair address 1. When the
Centurion is switched on, an OSD (On Screen Display) is shown on the image from the camera for approx 20
seconds.
PRO:360VTL CAM:0001 S
Centurion Software Version
Hybrid Analogue
PRO: Protocol being used for telemetry (e.g. 360 Vision Technology Ltd)
CAM: Camera RS485 ID (e.g. Cam 1)
S or L: Short or Long cable run. Use the utility to set whether the coax used to send video is under or over
300m.
Second Line: Shows the Centurion Software Version loaded into the camera.
Third Line: Shows current Hybrid mode.
To change the above settings in the camera, 360 Predator utility software, a USB/RS485 cable (PRED-
USB-485) and a laptop are required.
The Predator utility and PRED-USB-485 cable drivers can be found on the CD (shipped with the camera) or via
360 Vision Technology technical support.
Install the software (Predator-issued-120521-1-installer.exe) on the laptop being used. Connect the RS485 end
of the cable tted with a 3 way connector to the Centurion PSU 3 way RS485 port. Run the utility on the laptop
and then connect the USB end of the cable into the laptop. The utility will then search for new comms ports and
then will look for the camera across all baud rates used.
Settings that can be altered from this software are:
• Protocol: 360 (Coax/RS485), Pelco P 2400/4800/9600,
Pelco D 2400/4800/9600, Pelco Coaxitron (Extended version),
VCL (Coax/RS485), Ultrak (RS485), Forward Vision (RS485),
Molynx (Coax/RS485)*
• Coax Cable length: Longer than 300m or shorter than 300m.
• RS485 Address: Used on RS485 systems only.
*Molynx Coax is only available when the camera is ordered with
this requirement.
!

Centurion Hybrid Installation Manual V2.1.21 Page 11
8 Centurion OSD
OSD (On Screen Display) is accessed by dening/programming preset 6 or 95.
• Use the joystick up, down, left and right to navigate the menu. • Use the joystick zoom in to highlight/select an option. • Use joystick left and right to increment/decrement numbers.
Tour 001 item ...
PreDelSpd
Old................. New................ 0 1 2 3 4 5 6 7 8 9 Accept Item Accept Final Item Clear item Return Exit
DEFINE MIMIC
Mimic Number 001 Start Recording Return Exit
DEFINE PRESET
Preset Number ... 0 1 2 3 4 5 6 7 8 9 Accept Entry Clear Entry Return Exit
DEFINE HOME FUNCTION
Action Tour Number 001 Delay Minutes 010 Delay Seconds 000 Accept Changes Return
PRIVACY ZONE MENU
Dene Privacy Zone Seek Privacy Zone Remove Privacy Zone Return Exit
SERVICING
Power Reset Dome Factory Reset Dome Centurion Software Version Return Exit
Dene Tour Dene Mimic Dene Preset Dene Home Function Return
Dene Tour Dene Mimic Dene Preset Dene Home Function Settings Menu Text Field Menu Servicing Privacy Zone Menu Preset Mapping Return
SEEK PRESET
Preset Number ... 0 1 2 3 4 5 6 7 8 9 Accept Entry Clear Entry Return Exit
START TOUR
Tour Number 001 Start Tour Return Exit
START MIMIC
Mimic Number 001 Start Mimic Return Exit
DOME SETTINGS MENU
Pin Number ... 0 1 2 3 4 5 6 7 8 9 Accept Entry Clear Entry Return Exit
DOME MENU
Seek Preset Start Tour Start Mimic Dome Settings Menu Exit
8.1 PIN Number Operators PIN: 360 or 426 or 180 Controllers PIN: 1379 or 9731 Engineers PIN: 5498
TEXT FIELD EDIT
---------------------------------------
0123456789 :ABCDEFG HIJKLMNOPQRSTUVWXYZ
X Position: 000 Y Position: 000 TEXT Display: OFF Accept Entry Clear Entry Return
PRESET MAPPING
Presets 01 to 07 Presets 08 to 14 Presets 15 to 21 Return
General Settings Pelco Settings Night1 Settings Night2 Settings Lamps Settings Shutter Settings Return
WARNING
All Stored Data Will Be Permanently Erased Continue Return Exit
DEFINE PRIVACY ZONE
Privacy Zone ... 0 1 2 3 4 5 6 7 8 9 Accept Entry Clear Entry Return Exit
SEEK PRIVACY ZONE
Privacy Zone ... 0 1 2 3 4 5 6 7 8 9 Accept Entry Clear Entry Return Exit
REMOVE PRIVACY ZONE
Privacy Zone ... 0 1 2 3 4 5 6 7 8 9 Accept Entry Clear Entry Return Exit
FINISH MIMIC BY
DEFINING ANY PRESET
No. ACTION SEEK 01 a) none NO 02 b) none NO 03 c) none NO 04 d) none NO 05 e) none NO 06 f) none NO 07 g) none NO Accept Changes Return
Controller level Engineer level
Digital Zoom ON White Balance OUTDOOR Line Lock ON Line Phase +056 Video Gain 002 Video Lift 000 Wide Dynamic OFF Accept Changes Return
Auto Flip SEMI Proportional OFF Freeze Presets ON Zoom Speed 007 OSD Preset Six YES Upright Mount ON Aperture(day) 010 Accept Changes Return
Wiper Rest (s) 000 Wiper ON time (h) 000 Wiper ON time (m) 000 Wiper ON time (s) 000 Wiper Permanent OFF FV Text Control OFF AF AI When PTZ ON Noise Reduct (day) 0 Accept Changes Return
White Lamps YES White When Alarm ON White Timeout ON White Timeout (m) 001 Auto Dimming YES FV White Lights a)YES Accept Changes Return
Low Light Angle 000 Low Light Value 100% Accept Changes Return
Preset Dene On Pelco D Response NO Ultrak Cmd T/out ON Accept Changes Return
Aux1 a) auto focus Aux2 b) digital zoom Aux3 c) auto iris Aux4 d) ir Aux5 e) wiper Aux6 f) washer Aux7 g) osd Aux8 h) backlight Accept Changes Return
Col/Mono Change: Dark Mono On 020 Mono O󰀨 013 1=day 7=dusk 20=dark Bright Control Normal Accept Changes Return
Illumination IR Lamp Intensity 100% Camera Mono External Lighting Yes Aperture 3 Noise Reduction 0 Low Light Focus ON Night Presets OFF Accept Changes Return
Lamps1 Lamps2 Return
Fast Shutter OFF Fast Shutter Speed g:1/1000 Slow Shutter 1/3 sec Accept Changes Return
General1 Settings General2 Settings General3 Settings General4 Settings Return
Lamps Shutter
Night 2
Night 1
Pelco
General
General 1 General 2 General 3 General 4 Lamps 1 Lamps 2

Centurion Hybrid Installation Manual V2.1.21 Page 12
© 360 Vision Technology Ltd.
9 OSD Operation/Navigation
Dome menu
• Seek Preset
• Start Tour
• Start Mimic
• Dome Settings Menu
Dene Tour
A tour of presets is stored in the Centurion as a list of tour points. Each tour point consists of a preset number,
the dwell time for which the Centurion will pause and the speed parameter that will be used to seek the preset.
Each of the four tours of presets can contain between 2 and 90 points.
When programming a tour of presets it is necessary to rst store all the required presets into the Centurion and
to dene the required dwell times and speeds of travel that you will require the Centurion to use when the tour is
started.
A maximum of four individual tours of presets can be stored in each Centurion. Each tour can have between 2
and 360 points, each point can be a preset in the range 1 to 101. Di󰀨erent points can use any preset number,
including repeats of ones that have been used before. The speed that the camera will travel at to reach the
preset can be in the range 1°/sec (slowest) to 100°/sec (fastest). To seek the preset at maximum speed, set
speed to 0. The delay (dwell) at each point is dened in seconds, range 1 to 100.
This page will open on Tour 1, use the joystick left and right to change to another tour. To add item 1, use the
joystick to tilt down. This will highlight the number line so that the tour can be programmed. Use the joystick to
navigate along the number line and zoom in to select the number. This will add the number in to the NEW tour.
Add in the gures for the item/point in the tour using the sequence labelled above (PREDELSPD. PRE is preset
position, DEL is delay in seconds and SPD is speed at °/second). This is how the camera will be programmed to
move to a preset for a period of time at a set speed. All nine gures must be added into the item. Figures must
be added in three i.e. preset 21 will be added as 021.
Example of an item/point
021005100 = Move to preset 21 for 5 seconds at 100°/sec
Highlight ACCEPT ITEM and zoom in, this will add the item/point into the tour. The OLD item/point will be shown
on the screen. If these settings are acceptable, highlight the ACCEPT ITEM option and zoom in. There is no
need to add in these points again. Keep adding points until the tour is complete. On the nal item/point of the
tour highlight and zoom in on ACCEPT FINAL ITEM. This will complete the tour programming.
Dene Mimic (Before going into the OSD screen to programme a Mimic tour it is recommended to move the
camera in to the start position, any movement or delay will be recorded once the recording has started.)
When a mimic tour is started, the Centurion will perform all the actions which were dened when the mimic was
programmed. Up to four mimic tours can be dened.
Highlight and zoom in on START RECORDING, this will allow a mimic tour to be programmed into the camera.
The mimic tour can then be used to playback any manual movement, preset seek or delay. Program a preset to
end the mimic tour program.
Dene Preset
Before going into the OSD screen to programme a preset, the camera must be in the position required. Once in
the OSD you cannot manually move the camera.
Dene Home Function
The camera will perform an ACTION (goto preset, start preset or mimic tour), after a period of inactivity. Use the
NUMBER option to set which preset or tour to start, and the DELAY MINUTES/SECONDS to input the inactivity
time period.

Centurion Hybrid Installation Manual V2.1.21 Page 13
© 360 Vision Technology Ltd.
General Settings Menu
O󰀨ers more camera options.
General 1
• Digital Zoom - Use this option to enable or disable digital zoom.
• White Balance - Change the camera white balance settings to suit the area.
• Line Lock - Used to line lock the camera.
• Line Phase - Can be used to manually adjust the line phase.
• Video Gain - Used to adjust the video level to suit di󰀨erent lengths of coax cable.
• Video Lift - Used to adjust the frequency of the video level to suit di󰀨erent lengths of coax cable.
• Wide Dynamic - Enable WDR. Options available are ON, Auto and O󰀨. Default is o󰀨.
General 2
• Auto Flip - Use this option to set how the camera behaves when full tilt down is reached.
Semi - Requires a second tilt down command when at full tilt down to spin camera 180°.
Full - Automatically spins the camera 180°
• Proportional - Automatically reduces/increases pan/tilt speed depending on zoom ratio.
• Freeze Presets - This option freezes the image, when moving between presets.
• OSD Preset Six - Go into OSD using preset 95 and you can switch o󰀨 OSD access using preset 6.
• Upright Mount - Can be used to ip the image, so the camera can be used on a pole or a ceiling.
Default is pole.
• Aperture(day) - Can be used to increase the picture detail. Default is 10.
General 3
• Wiper Rest - Input a rest time for the wiper. (See Special Presets - page 36).
• Wiper On Time (h, m, & s) - Input a time period for the wiper operation.
(See Special Presets - page 36).
• Wiper Permanent - Enable or disable the permanent wiper time period.
• FV Text Control - Used on systems using Forward Vision protocol. Will add ANPR text on screen
when camera is put into fast shutter mode.
• AF AI When PTZ - Auto focus/iris will activate when PTZ is used, can be switched o󰀨. Default is on.
• Noise Reduction (day) - Used to reduce noise. NR must be set to suit the environment. Default is o󰀨.
General 4
• Dene Preset - Option to enable/disable the setting of presets. Default is on.
• Pelco D Response - Used on systems using Pelco D protocol where a response from the camera is
required. Do not use if the system doesn’t require a response as it will have an aect on the telemetry
control of the camera.
• Ultrak CMD T/out - Disables Ultrak KD6 100mS command timeout.
Pelco
Used when using Pelco protocol auxiliary commands. Associate a function of the camera to a Pelco Aux
command.
Night 1
• Col/Mono Level - Col/Mono level settings can be changed to suit the site requirements. Options are
dark, medium and light. Default is dark. This sets when the camera goes into ‘dark mode’.
• Mono On - Range is 7 to 25. A lower value will set the level on when the scene is brighter, a higher
value will set the level on when the scene is darker.
• Mono O󰀨 - Range is 1 to 20. A lower value will set the level o󰀨 when the scene is brighter, a higher
value will set the level o󰀨 when the scene is darker.
• Bright Control - Options are normal or automatic activation.
!

Centurion Hybrid Installation Manual V2.1.21 Page 14
© 360 Vision Technology Ltd.
Night 2
• Illumination - When the camera goes into dark mode, what illumination is required. Options are none,
IR and White Light. Please note illumination type will only work if the camera has this option tted to
the camera. Default is None.
• Lamp Intensity - Choose lamp intensity, options 100%, 80%, 60%, 40% and 20%. Default is 100%.
• Camera - Choose when the camera goes into dark mode, what the image will be. Options are mono
or colour. Default is Colour.
• External Lighting - Sets how the camera will focus (when in mono) to suit the light source in the
scene. If this is set incorrectly the image may not be in focus.
• Aperture - Can be used to increase the picture detail. Default is 3.
• Noise Reduction - Used to reduce noise with scenes of low illumination. NR must be set to suit the
environment. Default is 1.
• Low Light Focus - This can be set to on or o󰀨. When it is set to low the method used to focus the
camera is suited to low light conditions. Default is on.
• Night Presets -This can be used to set the presets to di󰀨erent settings if required. Default is o󰀨.
Lamps
O󰀨ers more camera options.
Lamps 1
• White Lamps - Set if white lights are to be used.
• White When Alarm - Set if white lights are to be used if an alarm is triggered. This feature works with
360 Standalone alarmcard or 360 Vision Matrix only.
• White Timeout - Use if a white light timer is required. Default is on.
• White Timeout (m) - Set white light timer, for automatic switch o󰀨.
• Auto Dimming - When selected the camera will reduce the lamp power, when looking in scenes
where there is too much light.
• FV White Lights - Used when using Forward Vision protocol, can be used to select what lamps are
controlled from the lamp command.
Lamps 2
• Low Light Angle - Sets angle when reduced illumination intensity is used.
• Low Light Value - Sets illumination intensity.
Centurion lamps are used to improve the illumination of distant dark objects. The Centurion lamps are normally
set to maximum intensity to increase the distance at which objects can be seen. When the Centurion lamps
are ON and the camera tilts downwards to view nearby objects, the illumination could be too bright. This could
cause the quality of the image to be reduced. Some Centurions include the ‘intelligent lighting’ feature which
allows the intensity of the illumination to be reduced when the Centurion tilts down below a particular angle (i.e.
the ‘Low Light Angle’). Below this angle the power to the lamps is reduced to the percentage value that has
been set (i.e. ‘Low Lights Value’).
Shutter
• Fast Shutter - Option to enable fast shutter and set speed of the shutter.
• Slow Shutter - Option to alter the slow shutter speed. Altering this gure will have an e󰀨ect on the low
light capabilities of the camera.

Centurion Hybrid Installation Manual V2.1.21 Page 15
© 360 Vision Technology Ltd.
Text Field Menu
Navigate along alpha-numeric characters and use zoom in to select. Choose text position by inputting x and y
co-ordinates. Set text display to on, if required.
Servicing
• Power Reset - This will reboot the camera, no settings will be lost.
• Factory Reset - This will reboot the camera and all the settings will be lost.
• Centurion Software Version - This shows the software version of the camera.
Privacy Zone Menu
Can be used to obscure a scene within an image e.g. private residence. Move the camera to the position
required for the privacy zone before going into the camera OSD. You cannot manually move the camera once
in the OSD. Use the zoom to set the size of the privacy zone. Privacy zone will cover the whole scene viewed
when set.
• Dene Privacy Zone - Used to set a privacy zone.
• Seek Privacy Zone - Used to seek a privacy zone.
• Remove Privacy Zone - Used to remove a privacy zone.
Preset Mapping
Use this option to re-map a function to a preset.
Options are:-
• none
• auto focus on
• auto iris on
• ir on
• wiper on
• white light
• fast shutter
• WDR
• ambient
• 20% lamp intensity
• 40% lamp intensity
• 60% lamp intensity
• 80% lamp intensity
• 100% lamp intensity
• video switch
• white day
• ir-mono
• mono
• normal night

Centurion Hybrid Installation Manual V2.1.21 Page 16
© 360 Vision Technology Ltd.
10 PSU Enclosure
Material PC/ABS
Dimensions (CENTHYB-PSU-SM enclosure) 255 x 180 x 100mm

Centurion Hybrid Installation Manual V2.1.21 Page 17
© 360 Vision Technology Ltd.
Centurion Hybrid
HD/IP
Installation/Conguration Section

Centurion Hybrid Installation Manual V2.1.21 Page 18
© 360 Vision Technology Ltd.
Centurion Hybrid Conguration
11 Locating the Centurion Hybrid on your Network
Default IP Address 192.168.1.187
Subnet 255.255.255.0
Gateway 192.168.1.4
Using the DVR management software, ‘Onvif Device Manager’ or 360 Vision Discovery Tool (which can be
found on the CD supplied or from the 360 Vision Technology technical support) to nd the IP address of the
Centurion Hybrid. Note the ports used by the Centurion Hybrid are:-
Protocol Port
ONVIF/HTTP 80 TCP
RTP Stream 1 6970 TCP/UDP
RTCP Stream 1 6971 TCP/UDP
RTP Stream 2 6972 TCP/UDP
RTCP Stream 2 6973 TCP/UDP
RTSP 554 TCP
360 SDK 3600 TCP
360 Event 9001 TCP
12 Connecting to the Centurion Hybrid
Type in the IP address of the Centurion Hybrid into the address bar of Mozilla Firefox. The web page of the
camera will then appear.
Centurion Hybrid Web Page Login screen
Enter the User Name (default is admin)
Enter the Password (default is 9999)

Centurion Hybrid Installation Manual V2.1.21 Page 19
© 360 Vision Technology Ltd.
Enter the User Name (default is admin)
Enter the Password (default is 9999)
If you select the box ‘Remember Password’ it could compromise the security of the Centurion Hybrid camera.
Select Submit
The camera web page uses VLC as the video player.
VLC video plugin le can be downloaded from the camera if it is not installed on the connecting PC/laptop
(See Browser - page 34)
!

Centurion Hybrid Installation Manual V2.1.21 Page 20
© 360 Vision Technology Ltd.
There are six main tabs on the left of the web page/screen.
1 Live View
2 Settings
3 Add/Edit Users
4 Maintenance
5 Browser
6 Logout
12.1 Live View
12.1.1 Live Video
The Live Video page o󰀨ers options to:-
• Stream - Choose required stream from drop down selection.
• 1x Display - Use to show selected stream as full screen.
• Zoom In/Out - This will operate the optical and digital zoom (if digital zoom is enabled).
(See Camera - Digital Zoom - page 26)
• Focus +/-/Auto - This will operate the manual focus near, far or automatically focus as required.
(See Camera - AF AI when PTZ - page 26)
• Iris +/-/Auto - This will operate the manual iris open, close or automatic as required.
(See Camera - AF AI when PTZ - page 26)
• Pan/Tilt - Use the up down left and right buttons to move the camera to the desired position.
• Preset Seek/Dene - This will allow admin and operator user levels to seek or dene presets (Viewer
user level can only seek presets). (See Advanced Features - Presets - page 24)
• List all presets - Use to show all presets or programmed presets in drop down selection box.