4xem Versa User manual

User's Manual
800MHz FSB Pentium 4 System
General Information....................................................................
Item Checklist.............................................................................
Mainboard Layout.......................................................................
Installation Procedure.................................................................
1 Processor/Memory Installation...............................................
2 Drive Installation.....................................................................
2.1 Corresponding models Standard, SPDIF, 1 LAN,
1Gb LAN, Mini PCI, 3 RS-232, TV-Out...........................
2.1.1 Installation.............................................................
2.1.2 Install Standard HDD............................................
2.1.3 Install CD-ROM.....................................................
2.1.4 Install Case...........................................................
2.1.5 Unpacking Procedure............................................
2.2 Corresponding models PCMCIA, 3 LAN, DVR-1,
DVR-4, CF reader............................................................
2.2.1 Installation.............................................................
2.2.2 Install Slim HDD....................................................
2.2.3 Install Standard HDD............................................
2.2.4 Install CD-ROM.....................................................
2.2.5 Install Case...........................................................
2.2.6 Unpacking Procedure...........................................
Upgrade Models...........................................................................
2
2
2
3
3
4
4
4
5
5
6
6
7
7
8
8
9
10
10
11
M0180

1-1
WARNING
The system uses entire casing for
partial heat dissipation, so the
normal operating temperature is
between 40 C ~ 55 C.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC ules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and if not installed and used in accordance with the instruction
manual may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
* eorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
* Consult the dealer or an experienced radio TV technician for help.
Notice: The changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equivalent.
1

General InformationGeneral Information
A. System Part List:
1. Mainboard
2. Installation Guide
3. CD
4. Power Adapter
5. Power Cable
6. Plastic Stand 4 pcs)
7. CPU Cooler
8. CPU FAN
2
Mainboard Layout
1
1
1
1
FAN1
1
JP1
CLEAR CMOS
IDE1 IDE2
LINE OUT
PORT
EAR PHONE
PORT
MIC IN
PORT
USB PORT1394 PORT
PWON
BUTTON
RST
BUTTON
HDD
LED
POWER
LED
19V EXT
POWER
PORT
PS/2 MOUSE
& KEYBOARD
PORTS
COM1
PORT
PARALLEL PORT
V A
PORT
LAN & USB PORTS
J10
67
42
811 10
1
1 Intel 865G Chipset
2 Intel 82801EB Chipset
3 I/O Chipset
4Audio CODEC Chipset
5 Flash EEPROM
6 CPU Socket 478
7 DDR DIMM Sockets
8IDE Connectors
9 PC104 Plus Connector option)
10 CPU FAN FAN 1)
11 Clear CMOS
CLEAR CMOS (JP1)
1
Pin 1-2 to Normal
Pin 2-3 to Cl ar
1
5
Front Panel Connector Rear Panel Connector
6
247
1 RJ45 LAN Port
2 Parallel Port
3PS/2 Mouse Port
4 USB Ports
5 VGA Port
6 RS232 COM Port
7 PS/2 Keyboard Port
8 19V Power In
9 LINE-Out Port
1
2 Power Button
3 Reset Button
4HDD LED
5 Power LED
6 Ear Phone Port
7
MIC-In Port
USB Port
81394 Port
B. Barebone System Part List:
1. Mainboard
2. Installation Guide
3. CD
4. Power Adapter
5. Power Cable
6. UDMA ATA Cable
7. CD-ROM Cable
8. CD-ROM Adapter
9. CPU FAN
10. CPU Cooler
11. Installation Accessory Pack
9 3
Item Checklist
86 1
321
54
7
8
9
53

Installation ProcedureInstallation Procedure
3
CPU socket level up to 90-degree.
1
Install CPU on CPU socket.
(Match socket pin 1 and CPU cut edge)
2
Install CPU cooler on CPU.
3
ighten CPU cooler with screws into
copper pillaret.
4
5
66
5
CPU FAN
CPU cooler
Rear Panel
7
Install CPU FAN on CPU Cooler.
5
ighten CPU FAN with screws to CPU Cooler.
6
Connect CPU FAN connector to mainboard
CPU FAN (FAN1) connector.
7
Note: Glue the heatsink compound between the CPU and heatsink.
1
2
3
4
90
CPU
Socket 478
CPU Cooler Screws
CPU FAN Screws
CPU cooler
Copper pillaret
Rear Panel
Heatsink
Compound
Install Memory
DIMM socket level down to 45-degree.
1
Install memory module into the DIMM socket.
2
1
2
45
45
Install CPU / Cooler
1 Processor / Memory Installation

Installation ProcedureInstallation Procedure
Part List
2 Drive Installation
2.1 Corresponding models: Standard, SPDIF, 1 LAN, 1Gb LAN, ini PCI,
3 RS-232, TV-Out
4
CD-ROM Bracket
CD-ROM Adapter
A
B
C
Plastic Spacer (* 2)
F
Standard HDD Screws / *4 (* 5)
CD-ROM Adapter Screws (* )
CD-ROM Screws (* 5)
G
Printer/COM/VGA Screws (* 6)
H
Case Screws (* 2)
I
P
Front Panel
J
Rear Panel
K
EMI Sticker (*2)
E
Plastic Stand (*4)
N
Q
CPU FAN Screws (* 2)
R
O
Mainboard
M
Case
L
CPU Cooler Screws (* 4)
S
CD-ROM Cable (210mm)
D
Installation Accessory Pack
2.1.1 Installation
Note:
Power input DC 19V only
Note
HDD Power Connector
A
E
J
D
C

Installation ProcedureInstallation Procedure
2.1.3 Install CD-ROM
5
Install Standard HDD to bracket.
1
Tighten Standard HDD with screws to bracket.
2
Install UDMA ATA cable to HDD device.
3
Install to HDD power connector.
4
Note
HDD Power onnector
A
J
D
C
2
2
HDD 1
N
HDD Power onnector
A
J
3
2
J
B
P
M
4
O D
2
D-ROM
3
5
5
6
K
Install D-ROM to D-ROM bracket.
1
Tighten D-ROM with screws to D-ROM bracket.
2
Insert plastic spacer to the D-ROM adapter.
3
Install D-ROM able to D-ROM adapter.
4
Tighten D-ROM adapter and D-ROM
with screws.
5
Put on the EMI sticker.
6
Before next step, you have to complete the install CPU cooler
and memory installation.
1
A
Note: Flip the Standard HDD over
2.1.2 Install Standard HDD

Installation ProcedureInstallation Procedure
6
Install mainboard into the case.
1
Tighten rear panel with screws on the case.
2
1
2
Stick on the plastic stand.
3
H
F
1
3
2
I
G
Q
Complete Memory
L
Complete CPU/cooler
2.1.5 Unpacking Procedure
Remove the screws on the rear panel from the case.
Pull out the mainboard from the case.
1
2
2
2.1.4 Install Case

Installation ProcedureInstallation Procedure
Part List
7
Installation Accessory Pack
2.2.1 Installation
Drive Adapter
CD-ROM Bracket
Insulate Pad
CD-ROM Adapter
A
B
C
D
HDD 40-pin Ca le
E
Plastic Spacer (* 2)
H
Slim HDD Screws / 3*6 (* 5)
Standard HDD Screws / 3*4 (* 5)
CD-ROM Adapter Screws (* 3)
CD-ROM Screws (* 5)
I
Printer/COM/VGA Screws (* 6)
J
Case Screws (* 2)
K
S
Front Panel
L
Rear Panel
M
EMI Sticker (*2)
P
Plastic Stand (*4)
Q
T
CPU FAN Screws (* 2)
U
R
Main oard
O
Case
N
F
Drive Adapter Screws (* 4)
G
CPU Cooler Screws (* 4)
V
Install and tighten CD-ROM racket, insulate pad
and the drive adapter with screws.
1
HDD Power Connector
B
D
G
A
1
2.2 Corresponding models: PCMCIA, 3 LAN, DVR-1, DVR- , CF reader

Installation ProcedureInstallation Procedure
2.2.3 Install Standard HDD
8
1
2
3
HDD
1
2
Install HDD to drive adapter.
Flip the drive adapter over.
Tighten HDD with screws.
IDE1/2 Connector
180
CD- OM 44-pin Connector
HDD 40-pin Connector
Note
AB
P
3
Install CD- OM 44-pin cable to CD- OM 44-pin connector.
1
Install HDD 40-pin cable to HDD 40-pin connector.
2
Install Standard HDD to bracket.
3
Tighten Standard HDD with screws to bracket.
4
Install HDD 40-pin cable to HDD device.
5
Install to HDD power connector.
6
P
u
l
l
Throu
g
h middle the ca
b
Power Connector
E
5
HDD
3
Note
Q
1
4
F
Pin 1
Pin 1
2
E
Note: Flip the Standard HDD over
Note: Slim HDD height < = 0.35 inch. ( 9 mm)
2.2.2 Install Slim HDD

Installation ProcedureInstallation Procedure
9
1
2
3
4
5
6
7
CD-ROM
Note
O
S
3
6
Install CD-ROM to CD-ROM bracket.
Tighten CD-ROM with screws to CD-ROM bracket.
Insert plastic spacer to the CD-ROM adapter.
Install CD-ROM 44-pin Cable to CD-ROM adapter.
Tighten CD-ROM adapter and CD-ROM with screws.
Install the drive adapter to the ainboard.
Put on the EMI sticker.
5
5
4
1
7
2
2
C
L
R
M
F
Before next step, you have to complete the install CPU/cooler
an memory installation.
Note:
Power input DC 19V only
2.2.4 Install CD-ROM

Installation ProcedureInstallation Procedure
10
Install mainboard into the case.
1
Tighten rear panel with screws on the case.
2
1
2
Stick on the plastic stand.
3
J
H
1
3
2
K
I
T
Complete Memory
N
Complete CPU/cooler
2.2.6 Unpacking Procedure
3Uninstall the drive adapter from the mainboard.
Remove the screws on the rear panel from the case.
Pull out the mainboard from the case.
1
2
3
2.2.5 Install Case

Upgrade ModelsUpgrade Models
11
Standard
PCMCIA
3 LAN
DVR -1
DVR -4
CF reader
SPDIF
1 LAN
1Gb LAN
Mini PCI
3 RS-232
TV-Out
Realtek 8139C
3*100Mb LAN
PCMCIA Realtek 8100C
LAN
addition
SPDIF
Realtek 8110S
LAN
expanable to
WIFI
3 addition
RS 232 ports
NTSC/PAL
output
1*BT878A
4*BT878A
CF reader
Specifications are subject to change without notice, reference only.