Fujitsu ESPRIMO C7xx User manual

System
Operating Manual
ESPRIMO C7xx / C9xx

Thank you for buying an innovative product from Fujitsu.
Latest information about our products, useful tips, updates etc. is available
on our website: "http://www.fujitsu.com/fts/"
You can find driver updates at: "http://support.ts.fujitsu.com/download"
Should you have any technical questions, please contact:
• our Hotline/Service Desk (see Service Desk list or from the Internet at:
"http://support.ts.fujitsu.com/contact/servicedesk")
• Your sales partner
• Your sales office
We hope you enjoy using your new Fujitsu system!

Published by / Contact address in the EU
Fujitsu Technology Solutions GmbH
Mies-van-der-Rohe-Straße 8
80807 Munich, Germany
"http://www.fujitsu.com/fts/"
Copyright
©Fujits
u Technology Solutions GmbH 2013. All rights reserved.
Publication Date
07/2013
Order No.: A26361-K1014-Z320-2-7619, edition 3

ESPRIMO C7xx / C9xx
Operating Manual
Your ESPRIMO 5
Important notes 7
Getting started 11
Operation 22
Troubleshooting and tips 28
System expansions 32
Technical data 53
Index 54

Remarks
Information on the product description meets the design specifications of Fujitsu and
is provided for comparison purposes. Several factors may cause the actual results to
differ. Technical data is subject to change without prior notification. Fujitsu rejects any
responsibility with regard to technical or editorial mistakes or omissions.
Trademarks
Fujitsu, the Fujitsu logo and ESPRIMO are registered trademarks of Fujitsu Limited or its
subsidiaries in the United States of America and other countries.
PS/2 is a registered trademark of International Business Machines, Inc.
Pentium is a registered trademark of Intel Corporation, USA.
Kensington, MicroSaver and K-Slot are registered trademarks of ACCO Brands.
Microsoft and Windows are trademarks or registered trademarks of the Microsoft
Corporation in the United States and/or other countries.
All other trademarks specified here are the property of their respective owners.
Copyright
No part of this publication may be copied, reproduced or translated without
the prior written consent of Fujitsu.
No part of this publication may be saved or transferred by any electronic means
without the written approval of Fujitsu.

Contents
Contents
YourESPRIMO ......................................................................... 5
Validityof theReferenceManual ......................................................... 5
Notational conventions .................................................................. 6
Importantnotes ........................................................................ 7
Safetyinformation ....................................................................... 7
Transporting the device .................................................................. 7
Cleaning thedevice ..................................................................... 8
Energy saving, disposalandrecycling .................................................... 8
CEmarking ............................................................................ 9
FCC Compliance Statement ............................................................. 10
FCC Class B Compliance Statement .................................................. 10
FCC Radiation ExposureStatement .................................................. 10
Gettingstarted ......................................................................... 11
Unpacking and checking the delivery . . ................................................... 11
Stepsforinitial setup .................................................................... 11
Setting upthedevice .................................................................... 12
Vertical operating position (optional) . . . . . . ............................................ 13
Horizontal operating position with rubber/plastic feet . . . . . . ............................. 14
Connecting the device to the mains voltage . . . ............................................ 15
Connecting external devices . . ........................................................... 16
Connecting the cables . .............................................................. 16
Disconnecting the cables . . . . . ....................................................... 16
Portson thedevice .................................................................. 17
Connecting a monitor . . . . . ........................................................... 17
Connecting the mouse . . . . ........................................................... 18
Connecting the keyboard . ........................................................... 18
Connecting external devices to the parallel (optional) or serial port . ..................... 19
Connecting external devices to the USB ports . ........................................ 19
Switchingonforthefirsttime:installingthesoftware ....................................... 20
Switchon themonitorandthemachine ............................................... 20
Installingthe software ............................................................... 21
Operation .............................................................................. 22
Switch thedevice on .................................................................... 22
Switchingoffthedevice ................................................................. 22
Indicatorson thedevice ................................................................. 23
Keyboard ............................................................................... 24
Important keys and keyboard shortcuts . . . . ............................................ 24
SettingsinBIOS Setup .................................................................. 25
Propertyanddataprotection ............................................................. 26
Anti-theftprotection .................................................................. 26
BIOS setupsecurityfunctions ........................................................ 26
Access authorization via SmartCard (optional) . ........................................ 27
Troubleshootingandtips .............................................................. 28
Helpifproblems occur ................................................................... 28
Troubleshooting . . . ...................................................................... 28
Power-on indicator does not light up after the device is switched on ..................... 28
The device cannot be switched off with the ON/OFF switch. . . . ......................... 29
Monitorremainsblank ............................................................... 29
Fujitsu 3

Contents
Nomousepointerdisplayedon thescreen ............................................ 30
Time and/or date is not correct . . . . . . ................................................. 30
Errormessagesonthe screen ........................................................ 30
Installingnewsoftware .................................................................. 30
Restoring theharddiskcontents ......................................................... 30
Tips .................................................................................... 31
Systemexpansions .................................................................... 32
Information about boards ................................................................ 33
Opening the casing . . ................................................................... 34
Closingthecasing ...................................................................... 35
Overview ofthedrivebaysand drivesin yourdevice ....................................... 35
Installingandremovingplasticdrive covers ............................................... 36
Removing theplasticdrive cover ..................................................... 36
Installingtheplastic drivecover ...................................................... 37
Installingandremovingthe drivecage .................................................... 37
Removing thedrivecage ............................................................ 37
Installingthedrive cage .............................................................. 38
Installing and removing the accessible 51/4inchdrive ...................................... 38
Removing anaccessibledrive ....................................................... 38
Installinganaccessibledrive ........................................................ 39
Installingandremovingthe harddiskdrive ................................................ 40
Removing theharddisk drive ........................................................ 40
Installingthehard diskdrive .......................................................... 41
Installing and removing a Compact Flash module (optional) . . .............................. 43
InstallingtheCompactFlashmodule .................................................. 43
Removing theCompactFlashmodule ................................................. 44
Installing/removing a SmartCard reader (optional) ......................................... 45
Installing the SmartCard reader . . . . . . ................................................. 45
Removing the SmartCard reader . . . . ................................................. 45
Installing and removing a WLAN module (optional) ......................................... 46
Installing the WLAN module . . ........................................................ 46
Removing the WLAN module . ........................................................ 47
Installing and removing a board . . ........................................................ 47
Installing a board . . . . ................................................................ 48
Removing boards ................................................................... 49
Installing and removing heat sinks ........................................................ 50
Removing the heat sink . . ............................................................ 50
Installing the heat sink . . . ............................................................ 50
Mainboard expansions . . ................................................................ 51
Upgrading mainmemory ............................................................. 51
Processor,replacing ................................................................. 51
Replacing thelithiumbattery ......................................................... 52
Technicaldata ......................................................................... 53
Index .................................................................................. 54
4Fujitsu

Your ESPRIMO
Your ESPRIMO
Overview
... is available with various configuration levels which differ in terms of hardware and software
equipment. You can install additional drives (for example a DVD drive) and other boards.
This manual tells you how to start using your device and how to operate it in daily use.
This manual applies for all configuration levels. Depending on the chosen configuration
level, some of the hardware components described may not be available on your PC.
Please also read the notes about your operating system.
Depending on the configuration selected, the operating system is preinstalled
on your hard disk (e.g. Windows).
Further information on this device is provided:
• in the "Quick Start Guide" poster
• in the "Safety/regulations" manual
• in the "Warranty" manual
• in the operating manual for the monitor
• in the manual for the mainboard
• in your operating system documentation
• in the information files (e.g. *.PDF, *.HTML, *.DOC, *.CHM, *.TXT, *.HLP)
Some of the manuals listed can be found in electronic form on the "Drivers & Utilities" DVD.
You can access and view the required information using the Acrobat Reader
program, which is also included on the DVD. You can of course also
print out a copy of the manual if you prefer.
ValidityoftheReferenceManual
This Reference Manual is valid for the following systems:
• ESPRIMO C700
• ESPRIMO C710
• ESPRIMO C720
• ESPRIMO C910-L
Fujitsu 5

Your ESPRIMO
Notational conventions
Pay particular attention to text marked with this symbol. Failure to observe
these warnings could pose a risk to health, damage the device or lead
to loss of data. The warranty will be invalidated if the device becomes
defective through failure to observe these warnings.
Indicates important information for the proper use of the device.
►Indicates an activity that must be performed
Indicates a result
This font indicates data entered using the keyboard in a program dialogue or at
the command line, e.g. your password (Name123) or a command used to
start a program (start.exe)
This font indicates information that is displayed on the screen by a program, e.g.:
Installation is complete.
This font indicates
• terms and texts used in a software interface, e.g.: Click on Save
• names of programs or files, e.g. Windows or setup.exe.
"This font" indicates
• cross-references to another section, e.g. "Safety information"
• cross-references to an external source, e.g. a web address: For more
information, go to "http://www.fujitsu.com/fts"
• Names of CDs, DVDs and titles or designations for other materials,
e.g.: "CD/DVD Drivers & Utilities" or "Safety/Regulations" manual
Key indicates a key on the keyboard, e.g: F10
This font indicates terms and texts that are emphasised or highlighted, e.g.: Do
not switch off the device
6Fujitsu

Important notes
Important notes
ImportantnotesNotes
In this chapter you will find information regarding safety which it is essential to
take note of when working with your device.
Safety information
SafetyinformationNote
Please note the information provided in the "Safety/regulations" manual
and in the following safety notes.
When installing and operating the device, please observe the notes on
environmental conditions in Chapter "Technical data", Page 53 as well as
the instructions in Chapter "Getting started", Page 11.
When setting up the device, make sure there is clearance all around it so that
thecasingreceivesenough ventilation. In order to avoid overheating, do not
cover the ventilation areas of the monitor or the device.
You must only operate the device if the rated voltage used by the
device is set to the local mains voltage.
The main switch (if present) and the ON/OFF switch do not disconnect the
device from the mains voltage. To completely disconnect from the mains
voltage, remove the power plug from the power socket.
Only operate the device with the casing closed.
Replace the lithium battery on the mainboard in accordance with the instructions
in "Replacing the lithium battery", Page 52.
Caution, components in the system can get very hot.
The activities described in these instructions must always be
performed with the greatest care.
Repairs to the device must only be performed by qualified technicians.
Incorrect repairs could put the user at great risk or cause serious damage
to the equipment (electric shock, risk of fire).
Transporting the device
Device,Trans portation Retransportation
Transport all parts separately in their original packaging or in a packaging which
protects them from knocks and jolts, to the new site.
Do not unpack them until all transportation manoeuvres are completed.
If the device is brought from a cold environment into the room where it will be used,
condensation may occur. Before operating the device, wait until it is absolutely dry
and has reached approximately the same temperature as the installation site.
Fujitsu 7

Important notes
Cleaning the device
Device,Transpo rtatio nRetransportationSystemu nit, see Device
Turn off all power and equipment switches and disconnect the power
plug from the mains outlet.
Do not clean any interior parts yourself, leave this job to a service technician.
Do not use any cleaning agents that contain abrasives or may corrode
plastic (alcohol, thinner or acetone).
Never clean the device with water! Water entering into the device could
present a serious risk to users (e.g. electric shock).
Ensure that no liquid enters the system.
The surface can be cleaned with a dry cloth. If particularly dirty, use a cloth that has been
moistened in mild domestic detergent and then carefully wrung out.
Use disinfectant wipes to clean the keyboard and the mouse.
Energy saving, disposal and recycling
DisposalEnergysavingRecyclingDrivers&UtilitiesDVDUserDocumentationDVD
You can find information on these subjects on the "Drivers & Utilities" DVD or on our
website ("http://www.fujitsu.com/fts/about/fts/environment-care/").
8Fujitsu

Important notes
CE marking
CEmarkingCEmarkingNotesElectromagneticcompatibilityLowvoltage directive
The shipped version of this device complies with the requirements of European Union
directives 2004/108/EC "Electromagnetic compatibility", 2006/95/EC "Low voltage directive" and
2009/125/EC "Ecodesign".
CE marking for devices with radio component
This equipment complies with the requirements of Directive 1999/5/EC of the European Parliament
and Commission from 9 March, 1999 governing Radio and Telecommunications Equipment
and mutual recognition of conformity.
The CE marking valid for your device can be found on the device label.
Explanation: CE nnnn (!); nnnn defines the type of CE marking and the exclamation mark indicates
a device with radio components.
You can find more information and declarations of conformity on the Internet at:
"http://globalsp.ts.fujitsu.com/sites/certificates".
This equipment can be used in the following countries:
Belgium Bulgaria Denmark Germany
Estonia Finland France Greece
UK Ireland Iceland Italy
Croatia Latvia Liechtenstein Lithuania
Luxembourg Malta Netherlands Norway
Austria Poland Portugal Rumania
Sweden Switzerland Slovakia Slovenia
Spain Czech Republic Hungary Cyprus
Contact the corresponding government office in the respective country for current information on
possible operating restrictions. If your country is not included in the list, then please contact
the corresponding supervisory authority as to whether the use of this product is permitted in
your country.
Fujitsu 9

Important notes
FCC Compliance Statement
If the device complies with the FCC regulations, the FCC sign can be found on the type rating plate.
FCC Class B Compliance Statement
DOC (INDUSTRY CANADA) NOTICES
Notice to Users of Radios and Television:
This class B digital apparatus complies with Canadian ICES-003.
The following statement applies to the products covered in this manual, unless otherwise specified
herein. The statement for other products will appear in the accompanying documentation.
NOTE:
This equipment has been tested and found to comply with the limits for a "Class B" digital
device, pursuant to Part 15 of the FCC rules and meets all requirements of the Canadian
Interference-Causing Equipment Standard ICES-003 for digital apparatus. These limits are
designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in strict accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Fujitsu is not responsible for any radio or television interference caused by unauthorized
modifications of this equipment or the substitution or attachment of connecting cables and
equipment other than those specified by Fujitsu. The correction of interferences caused by such
unauthorized modification, substitution or attachment will be the responsibility of the user.
The use of shielded I/O cables is required when connecting this equipment to any and all optional
peripheral or host devices. Failure to do so may violate FCC and ICES rules.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
The transmitters in this device must not be co-located or operated in conjunction
with any other antenna or transmitter.
To prevent radio interference to the licensed service, this device is intended to be
operated indoors and away from windows to provide maximum shielding. Equipment (or
its transmit antenna) that is installed outdoors is subject to licensing.
Users are not authorized to modify this product. Any modifications invalidate the warranty.
This equipment may not be modified, altered, or changed in any way without signed
written permission from Fujitsu. Unauthorized modification will void the equipment
authorization from the FCC and Industry Canada and the warranty.
10 Fujitsu

Getting started
Getting started
Gettingstarted
Please observe the safety information in the "Important notes", Page 7 chapter.
Unpacking and checking the delivery
It is recommended not to throw away the original packaging material! It may be
required for reshipment at some later date.
PackagingContentso fdeliveryPackaging,
►Unpack all the individual parts.
►Check the contents of the package for any visible damage caused during transport.
►Check whether the delivery conforms to the details in the delivery note.
►Should you discover that the delivery does not correspond to the delivery
note, notify your local sales outlet immediately.
Steps for initial setup
Preparingf orfirstuse, overviewPreparingforuse,
Only a few steps are necessary to put your new device into operation for the first time:
• Select a location for device and set up device
• Connect external devices such as mouse, keyboard and monitor
• Check the voltage at the mains outlet and connect the device to an electrical outlet
• Switch the device on
You will learn more about the individual steps in the following sections.
External devices
If you have received other external devices in addition to your own device (e.g.
a printer), do not connect these until after the initial installation. The following
sections describe how to connect these external devices.
Drives and boards
If you have received drives or boards with your device, please do not install
them until after first-time setup. How to install drives and boards is described
in the "System expansions", Page 32 chapter.
Fujitsu 11

Getting started
Setting up the device
Workstati onErgonomicDevice
When installing your device, please read the recommendations and safety
notes in the "Safety/regulations" manual.
We recommend that you place your device on a surface which is not slippery. In
view of the many different finishes and varnishes used on furniture, it is possible
that the rubber feet will mark the surface they stand on.
Depending on the location of your device, bothersome vibrations and noises may
occur. To prevent this, a distance of at least 10 mm / 0.39 inch should be maintained
from other devices on casing sides without ventilation surfaces.
In order to avoid overheating, do not cover the ventilation areas
of the monitor or the device.
A minimum distance of 200 mm / 7.87 inch from the device must
be observed for ventilation areas.
Do not stack several devices on top of each other.
Do not expose the device to extreme ambient conditions (see "Technical data", Page 53,
section "Ambient conditions"). Protect the device against dust, humidity and heat.
12 Fujitsu

Getting started
Operating position
You can use the device in a vertical or horizontal operating position.
Vertical operating position (optional)
Operation in the vertical operating position is not allowed in Taiwan.
Proceed as follows to operate the device in the vertical operating position:
Verticaloperatingposition Operatingpos ition,verti cal Rubber/plasticfeetSide cover
►Disconnect the cables if required.
►Pull off the foil from the rubber/plastic feet included in the pack of accessories.
►Stick the rubber/plastic feet to the underside of the casing. In order to ensure a
that the unit is stable, the rubber/plastic feet should be located in approximately
the positions shown in the illustration.
►Place the device vertically on the rubber/plastic feet.
►If necessary, reconnect any cables that were previously disconnected.
Fujitsu 13

Getting started
Horizontal operating position with rubber/plastic feet
HorizontaloperatingpositionOperatingpos ition,horizon talRubber/plastic feet
The horizontal operating position is only permitted with the rubber/plastic
feet (due to the heat generated on the underside).
►If necessary, disconnect the cables.
►Place the device on its upper side on a sturdy, flat and clean surface.
►Stick the rubber/plastic feet (1) to the
underside of the casing.
►To ensure a that the device is stable,
the rubber/plastic feet should be fixed
in similar positions to the ones shown
in the illustration.
►Place the device on the rubber/plastic feet.
►If necessary, reconnect any cables that
were previously disconnected.
14 Fujitsu

Getting started
Connecting the device to the mains voltage
DeviceConnectingDevice
►Check the voltage setting.
2
1
►Connect the power cable to the device.
►Plug the power plug into a properly grounded mains outlet.
The device is fitted with a wide voltage range power supply. This means you
do not need to set the nominal voltage manually for these devices. Therefore
there is no switch available for the voltage setting.
Fujitsu 15

Getting started
Connecting external devices
Read the documentation on the external device before connecting it.
With the exception of USB devices, always remove all power plugs
before connecting external devices!
Do not connect or disconnect cables during a thunderstorm.
Always take hold of the actual plug. Never unplug a cable by pulling the cable itself.
Connect and disconnect the cables in the order described below.
Connecting the cables
►Turn off all power and equipment switches.
CordCable,
►Remove all power plugs from the grounded mains outlets.
►Connect all the cables to the device and the external devices. Please make sure that you
always observe the safety notes provided in "Important notes", Page 7.
►Plug all data communication cables into the appropriate sockets.
►Plug all power cables into the grounded mains outlets.
USB devices are hot-pluggable. This means you can connect and disconnect
USB cables while your device is switched on.
Additional information can be found in "Connecting external devices to the USB
ports", Page 19 and in the documentation for the USB devices.
Disconnecting the cables
►Switch off all affected devices.
Cable,
►Remove all power plugs from the grounded mains outlets.
►Unplug all data communication cables from the appropriate sockets.
►Disconnect all of the cables from the device and from the external devices.
16 Fujitsu