7-Eleven 24/7life 160499 User manual
WATER RESISTANT
WIRELESS SPEAKER Model: 160499
Warnings
Battery warning!
• ”Caution”– The battery used in the product may present a risk of re
or chemical burn if mistreated. Batteries may explode if damaged.
• Only recharge your battery with the provided approved cable
designated for the product.
• Dispose of batteries according to local regulations. Please recycle
when possible. Do not dispose the battery as household waste or in
a re as it may explode.
• The battery in your product can not be removed or replaced by the
user. Any attempt to do so is unsafe and may result in damage of
the product.
Built-in Battery Care:
• Your product is powered by a rechargeable battery. Optimal
performance of a new battery is achieved only after two or three
complete charge and discharge cycles. Do not leave a fully charged
battery connected to a charger, since overcharging may shorten its
lifetime.
• If left unused, a fully charged battery will lose its charge over time.
• Leaving the product in hot or cold places, such as in a closed car in
summer or winter conditions, will reduce the capacity and lifetime
of the battery.
• Always try to keep the battery between 32°F and 113°F. A product
may not work temporarily with an extremely hot or cold battery,
even when the battery is fully charged.
Important Safety Precautions
Read all instructions before using your Wireless Speaker.
• Never expose your product to high temperatures, extreme cold or
submerse in water.
• If the product overheats, has been dropped or damaged or has been
dropped in a liquid, discontinue use.
• In order to avoid the risk of electric shock, never attempt to open
your product or repair it, consult a certied professional.
• If you detect any abnormalities when using your product
immediately discontinue use and contact the manufacturer.
• Unplug your product when it will not be in use for long periods of
time or during lightning storms.
• Never mount or store the product over any airbag deployment area,
as serious injury may result when an airbag deploys.
• Do not dispose of product in heat or re.
• Do not clean the product with harmful chemicals or detergents.
Product Overview
Power
Mode
Indicator Light/Microphone
Volume
-
/ Previous Track
Volume + / Next Track
Auxiliary Audio Input Jack
Micro-USB Charging Port
Water Resistant Cover
1
2
3
5
6
7
IPX4 water resistance rating:
Wireless speaker is protected against
splashing water for a short period of time.
Note: The wireless speaker is NOT waterproof and can not be used
while swimming, showering or submerged in water.
Bluetooth® Connection (Pairing)
Bluetooth® Connection Trouble Shooting
Why won’t the wireless speaker connect to my device?
a. The Bluetooth setting on your device may have been turned o.
Turn on the Bluetooth function and search for“
24/7 LIFE BT
Speaker”
.
b.The wireless speaker may have been connected to another device.
Disconnect (unpair) the speaker from the previous device before
connecting it to your device.
c.The wireless speaker may not have been recognized by your device.
Turn o the wireless speaker then turn it back on. Search your
Bluetooth settings on your device and connect the wireless
speaker.
d.The wireless speaker may be to far away from the device to
connect. Make sure there are no obstacles between the devices
and reconnect the wireless speaker.
1 2 3 45
6 7
4
Turning On/O the Wireless Speaker
Turning On: Press and hold button for 2 seconds until indicator
light ashes and you hear“Power on, wireless mode”.
Note: If you have an aux cable plugged into the auxiliary audio input
jack you will hear“Power on, audio mode”.
Turning O: Press and hold button for 2 seconds until indicator
light turns o and you hear a“Power o”.
1. Turn on the wireless speaker by pressing and holding the
button for 2 seconds until indicator light ashes and you hear
“Power on, wireless mode”.
2. Place the wireless speaker and the Bluetooth device (phone) so
that they are no further than 3ft apart.
3. Activate the Bluetooth function on your Bluetooth device. (Refer
to the manufacturer’s instruction manual to enable Bluetooth on
your device).
4. Select “24/7 LIFE BT Speaker”from the list of available Bluetooth
devices. If required enter password“0000”. If“24/7 LIFE BT
Speaker”does not appear in your device turn o the Bluetooth
function on your device then turn it back on.
5. Once paired successfully, you will hear a conrmation“Connected”
and the indicator light will be on solid.
Note 1: Once you have paired the speaker with a device, the speaker
will remember this device and will pair automatically when the
device’s Bluetooth is activated and in range.
Note 2: The speaker will attempt to automatically connect to the last
device it was paired with when switch on. If you want to pair it with
a new device, disconnect (unpair) the speaker from the previous
device and follow the steps outlined above.
Cover must be in place to
retain the speaker’s water
resistant feature.
8
8
Water Resistant
BC
WATER RESISTANT
WIRELESS SPEAKER Model: 160499
Warnings
Battery warning!
• ”Caution”– The battery used in the product may present a risk of re
or chemical burn if mistreated. Batteries may explode if damaged.
• Only recharge your battery with the provided approved cable
designated for the product.
• Dispose of batteries according to local regulations. Please recycle
when possible. Do not dispose the battery as household waste or in
a re as it may explode.
• The battery in your product can not be removed or replaced by the
user. Any attempt to do so is unsafe and may result in damage of
the product.
Built-in Battery Care:
• Your product is powered by a rechargeable battery. Optimal
performance of a new battery is achieved only after two or three
complete charge and discharge cycles. Do not leave a fully charged
battery connected to a charger, since overcharging may shorten its
lifetime.
• If left unused, a fully charged battery will lose its charge over time.
• Leaving the product in hot or cold places, such as in a closed car in
summer or winter conditions, will reduce the capacity and lifetime
of the battery.
• Always try to keep the battery between 32°F and 113°F. A product
may not work temporarily with an extremely hot or cold battery,
even when the battery is fully charged.
Important Safety Precautions
Read all instructions before using your Wireless Speaker.
• Never expose your product to high temperatures, extreme cold or
submerse in water.
• If the product overheats, has been dropped or damaged or has been
dropped in a liquid, discontinue use.
• In order to avoid the risk of electric shock, never attempt to open
your product or repair it, consult a certied professional.
• If you detect any abnormalities when using your product
immediately discontinue use and contact the manufacturer.
• Unplug your product when it will not be in use for long periods of
time or during lightning storms.
• Never mount or store the product over any airbag deployment area,
as serious injury may result when an airbag deploys.
• Do not dispose of product in heat or re.
• Do not clean the product with harmful chemicals or detergents.
Product Overview
Power
Mode
Indicator Light/Microphone
Volume
-
/ Previous Track
Volume + / Next Track
Auxiliary Audio Input Jack
Micro-USB Charging Port
Water Resistant Cover
1
2
3
5
6
7
IPX4 water resistance rating:
Wireless speaker is protected against
splashing water for a short period of time.
Note: The wireless speaker is NOT waterproof and can not be used
while swimming, showering or submerged in water.
Bluetooth® Connection (Pairing)
Bluetooth® Connection Trouble Shooting
Why won’t the wireless speaker connect to my device?
a. The Bluetooth setting on your device may have been turned o.
Turn on the Bluetooth function and search for“
24/7 LIFE BT
Speaker”
.
b.The wireless speaker may have been connected to another device.
Disconnect (unpair) the speaker from the previous device before
connecting it to your device.
c.The wireless speaker may not have been recognized by your device.
Turn o the wireless speaker then turn it back on. Search your
Bluetooth settings on your device and connect the wireless
speaker.
d.The wireless speaker may be to far away from the device to
connect. Make sure there are no obstacles between the devices
and reconnect the wireless speaker.
1 2 3 45
6 7
4
Turning On/O the Wireless Speaker
Turning On: Press and hold button for 2 seconds until indicator
light ashes and you hear“Power on, wireless mode”.
Note: If you have an aux cable plugged into the auxiliary audio input
jack you will hear“Power on, audio mode”.
Turning O: Press and hold button for 2 seconds until indicator
light turns o and you hear a“Power o”.
1. Turn on the wireless speaker by pressing and holding the
button for 2 seconds until indicator light ashes and you hear
“Power on, wireless mode”.
2. Place the wireless speaker and the Bluetooth device (phone) so
that they are no further than 3ft apart.
3. Activate the Bluetooth function on your Bluetooth device. (Refer
to the manufacturer’s instruction manual to enable Bluetooth on
your device).
4. Select “24/7 LIFE BT Speaker”from the list of available Bluetooth
devices. If required enter password“0000”. If“24/7 LIFE BT
Speaker”does not appear in your device turn o the Bluetooth
function on your device then turn it back on.
5. Once paired successfully, you will hear a conrmation“Connected”
and the indicator light will be on solid.
Note 1: Once you have paired the speaker with a device, the speaker
will remember this device and will pair automatically when the
device’s Bluetooth is activated and in range.
Note 2: The speaker will attempt to automatically connect to the last
device it was paired with when switch on. If you want to pair it with
a new device, disconnect (unpair) the speaker from the previous
device and follow the steps outlined above.
Cover must be in place to
retain the speaker’s water
resistant feature.
8
8
Water Resistant
BC
WATER RESISTANT
WIRELESS SPEAKER Model: 160499
Warnings
Battery warning!
• ”Caution”– The battery used in the product may present a risk of re
or chemical burn if mistreated. Batteries may explode if damaged.
• Only recharge your battery with the provided approved cable
designated for the product.
• Dispose of batteries according to local regulations. Please recycle
when possible. Do not dispose the battery as household waste or in
a re as it may explode.
• The battery in your product can not be removed or replaced by the
user. Any attempt to do so is unsafe and may result in damage of
the product.
Built-in Battery Care:
• Your product is powered by a rechargeable battery. Optimal
performance of a new battery is achieved only after two or three
complete charge and discharge cycles. Do not leave a fully charged
battery connected to a charger, since overcharging may shorten its
lifetime.
• If left unused, a fully charged battery will lose its charge over time.
• Leaving the product in hot or cold places, such as in a closed car in
summer or winter conditions, will reduce the capacity and lifetime
of the battery.
• Always try to keep the battery between 32°F and 113°F. A product
may not work temporarily with an extremely hot or cold battery,
even when the battery is fully charged.
Important Safety Precautions
Read all instructions before using your Wireless Speaker.
• Never expose your product to high temperatures, extreme cold or
submerse in water.
• If the product overheats, has been dropped or damaged or has been
dropped in a liquid, discontinue use.
• In order to avoid the risk of electric shock, never attempt to open
your product or repair it, consult a certied professional.
• If you detect any abnormalities when using your product
immediately discontinue use and contact the manufacturer.
• Unplug your product when it will not be in use for long periods of
time or during lightning storms.
• Never mount or store the product over any airbag deployment area,
as serious injury may result when an airbag deploys.
• Do not dispose of product in heat or re.
• Do not clean the product with harmful chemicals or detergents.
Product Overview
Power
Mode
Indicator Light/Microphone
Volume
-
/ Previous Track
Volume + / Next Track
Auxiliary Audio Input Jack
Micro-USB Charging Port
Water Resistant Cover
1
2
3
5
6
7
IPX4 water resistance rating:
Wireless speaker is protected against
splashing water for a short period of time.
Note: The wireless speaker is NOT waterproof and can not be used
while swimming, showering or submerged in water.
Bluetooth® Connection (Pairing)
Bluetooth® Connection Trouble Shooting
Why won’t the wireless speaker connect to my device?
a. The Bluetooth setting on your device may have been turned o.
Turn on the Bluetooth function and search for“
24/7 LIFE BT
Speaker”
.
b.The wireless speaker may have been connected to another device.
Disconnect (unpair) the speaker from the previous device before
connecting it to your device.
c.The wireless speaker may not have been recognized by your device.
Turn o the wireless speaker then turn it back on. Search your
Bluetooth settings on your device and connect the wireless
speaker.
d.The wireless speaker may be to far away from the device to
connect. Make sure there are no obstacles between the devices
and reconnect the wireless speaker.
1 2 3 45
6 7
4
Turning On/O the Wireless Speaker
Turning On: Press and hold button for 2 seconds until indicator
light ashes and you hear“Power on, wireless mode”.
Note: If you have an aux cable plugged into the auxiliary audio input
jack you will hear“Power on, audio mode”.
Turning O: Press and hold button for 2 seconds until indicator
light turns o and you hear a“Power o”.
1. Turn on the wireless speaker by pressing and holding the
button for 2 seconds until indicator light ashes and you hear
“Power on, wireless mode”.
2. Place the wireless speaker and the Bluetooth device (phone) so
that they are no further than 3ft apart.
3. Activate the Bluetooth function on your Bluetooth device. (Refer
to the manufacturer’s instruction manual to enable Bluetooth on
your device).
4. Select “24/7 LIFE BT Speaker”from the list of available Bluetooth
devices. If required enter password“0000”. If“24/7 LIFE BT
Speaker”does not appear in your device turn o the Bluetooth
function on your device then turn it back on.
5. Once paired successfully, you will hear a conrmation“Connected”
and the indicator light will be on solid.
Note 1: Once you have paired the speaker with a device, the speaker
will remember this device and will pair automatically when the
device’s Bluetooth is activated and in range.
Note 2: The speaker will attempt to automatically connect to the last
device it was paired with when switch on. If you want to pair it with
a new device, disconnect (unpair) the speaker from the previous
device and follow the steps outlined above.
Cover must be in place to
retain the speaker’s water
resistant feature.
8
8
Water Resistant
BC
WATER RESISTANT
WIRELESS SPEAKER Model: 160499
Warnings
Battery warning!
• ”Caution”– The battery used in the product may present a risk of re
or chemical burn if mistreated. Batteries may explode if damaged.
• Only recharge your battery with the provided approved cable
designated for the product.
• Dispose of batteries according to local regulations. Please recycle
when possible. Do not dispose the battery as household waste or in
a re as it may explode.
• The battery in your product can not be removed or replaced by the
user. Any attempt to do so is unsafe and may result in damage of
the product.
Built-in Battery Care:
• Your product is powered by a rechargeable battery. Optimal
performance of a new battery is achieved only after two or three
complete charge and discharge cycles. Do not leave a fully charged
battery connected to a charger, since overcharging may shorten its
lifetime.
• If left unused, a fully charged battery will lose its charge over time.
• Leaving the product in hot or cold places, such as in a closed car in
summer or winter conditions, will reduce the capacity and lifetime
of the battery.
• Always try to keep the battery between 32°F and 113°F. A product
may not work temporarily with an extremely hot or cold battery,
even when the battery is fully charged.
Important Safety Precautions
Read all instructions before using your Wireless Speaker.
• Never expose your product to high temperatures, extreme cold or
submerse in water.
• If the product overheats, has been dropped or damaged or has been
dropped in a liquid, discontinue use.
• In order to avoid the risk of electric shock, never attempt to open
your product or repair it, consult a certied professional.
• If you detect any abnormalities when using your product
immediately discontinue use and contact the manufacturer.
• Unplug your product when it will not be in use for long periods of
time or during lightning storms.
• Never mount or store the product over any airbag deployment area,
as serious injury may result when an airbag deploys.
• Do not dispose of product in heat or re.
• Do not clean the product with harmful chemicals or detergents.
Product Overview
Power
Mode
Indicator Light/Microphone
Volume
-
/ Previous Track
Volume + / Next Track
Auxiliary Audio Input Jack
Micro-USB Charging Port
Water Resistant Cover
1
2
3
5
6
7
IPX4 water resistance rating:
Wireless speaker is protected against
splashing water for a short period of time.
Note: The wireless speaker is NOT waterproof and can not be used
while swimming, showering or submerged in water.
Bluetooth® Connection (Pairing)
Bluetooth® Connection Trouble Shooting
Why won’t the wireless speaker connect to my device?
a. The Bluetooth setting on your device may have been turned o.
Turn on the Bluetooth function and search for“
24/7 LIFE BT
Speaker”
.
b.The wireless speaker may have been connected to another device.
Disconnect (unpair) the speaker from the previous device before
connecting it to your device.
c.The wireless speaker may not have been recognized by your device.
Turn o the wireless speaker then turn it back on. Search your
Bluetooth settings on your device and connect the wireless
speaker.
d.The wireless speaker may be to far away from the device to
connect. Make sure there are no obstacles between the devices
and reconnect the wireless speaker.
1 2 3 45
6 7
4
Turning On/O the Wireless Speaker
Turning On: Press and hold button for 2 seconds until indicator
light ashes and you hear“Power on, wireless mode”.
Note: If you have an aux cable plugged into the auxiliary audio input
jack you will hear“Power on, audio mode”.
Turning O: Press and hold button for 2 seconds until indicator
light turns o and you hear a“Power o”.
1. Turn on the wireless speaker by pressing and holding the
button for 2 seconds until indicator light ashes and you hear
“Power on, wireless mode”.
2. Place the wireless speaker and the Bluetooth device (phone) so
that they are no further than 3ft apart.
3. Activate the Bluetooth function on your Bluetooth device. (Refer
to the manufacturer’s instruction manual to enable Bluetooth on
your device).
4. Select “24/7 LIFE BT Speaker”from the list of available Bluetooth
devices. If required enter password“0000”. If“24/7 LIFE BT
Speaker”does not appear in your device turn o the Bluetooth
function on your device then turn it back on.
5. Once paired successfully, you will hear a conrmation“Connected”
and the indicator light will be on solid.
Note 1: Once you have paired the speaker with a device, the speaker
will remember this device and will pair automatically when the
device’s Bluetooth is activated and in range.
Note 2: The speaker will attempt to automatically connect to the last
device it was paired with when switch on. If you want to pair it with
a new device, disconnect (unpair) the speaker from the previous
device and follow the steps outlined above.
Cover must be in place to
retain the speaker’s water
resistant feature.
8
8
Water Resistant
BC
WATER RESISTANT
WIRELESS SPEAKER Model: 160499
Warnings
Battery warning!
• ”Caution”– The battery used in the product may present a risk of re
or chemical burn if mistreated. Batteries may explode if damaged.
• Only recharge your battery with the provided approved cable
designated for the product.
• Dispose of batteries according to local regulations. Please recycle
when possible. Do not dispose the battery as household waste or in
a re as it may explode.
• The battery in your product can not be removed or replaced by the
user. Any attempt to do so is unsafe and may result in damage of
the product.
Built-in Battery Care:
• Your product is powered by a rechargeable battery. Optimal
performance of a new battery is achieved only after two or three
complete charge and discharge cycles. Do not leave a fully charged
battery connected to a charger, since overcharging may shorten its
lifetime.
• If left unused, a fully charged battery will lose its charge over time.
• Leaving the product in hot or cold places, such as in a closed car in
summer or winter conditions, will reduce the capacity and lifetime
of the battery.
• Always try to keep the battery between 32°F and 113°F. A product
may not work temporarily with an extremely hot or cold battery,
even when the battery is fully charged.
Important Safety Precautions
Read all instructions before using your Wireless Speaker.
• Never expose your product to high temperatures, extreme cold or
submerse in water.
• If the product overheats, has been dropped or damaged or has been
dropped in a liquid, discontinue use.
• In order to avoid the risk of electric shock, never attempt to open
your product or repair it, consult a certied professional.
• If you detect any abnormalities when using your product
immediately discontinue use and contact the manufacturer.
• Unplug your product when it will not be in use for long periods of
time or during lightning storms.
• Never mount or store the product over any airbag deployment area,
as serious injury may result when an airbag deploys.
• Do not dispose of product in heat or re.
• Do not clean the product with harmful chemicals or detergents.
Product Overview
Power
Mode
Indicator Light/Microphone
Volume
-
/ Previous Track
Volume + / Next Track
Auxiliary Audio Input Jack
Micro-USB Charging Port
Water Resistant Cover
1
2
3
5
6
7
IPX4 water resistance rating:
Wireless speaker is protected against
splashing water for a short period of time.
Note: The wireless speaker is NOT waterproof and can not be used
while swimming, showering or submerged in water.
Bluetooth® Connection (Pairing)
Bluetooth® Connection Trouble Shooting
Why won’t the wireless speaker connect to my device?
a. The Bluetooth setting on your device may have been turned o.
Turn on the Bluetooth function and search for“
24/7 LIFE BT
Speaker”
.
b.The wireless speaker may have been connected to another device.
Disconnect (unpair) the speaker from the previous device before
connecting it to your device.
c.The wireless speaker may not have been recognized by your device.
Turn o the wireless speaker then turn it back on. Search your
Bluetooth settings on your device and connect the wireless
speaker.
d.The wireless speaker may be to far away from the device to
connect. Make sure there are no obstacles between the devices
and reconnect the wireless speaker.
1 2 3 45
6 7
4
Turning On/O the Wireless Speaker
Turning On: Press and hold button for 2 seconds until indicator
light ashes and you hear“Power on, wireless mode”.
Note: If you have an aux cable plugged into the auxiliary audio input
jack you will hear“Power on, audio mode”.
Turning O: Press and hold button for 2 seconds until indicator
light turns o and you hear a“Power o”.
1. Turn on the wireless speaker by pressing and holding the
button for 2 seconds until indicator light ashes and you hear
“Power on, wireless mode”.
2. Place the wireless speaker and the Bluetooth device (phone) so
that they are no further than 3ft apart.
3. Activate the Bluetooth function on your Bluetooth device. (Refer
to the manufacturer’s instruction manual to enable Bluetooth on
your device).
4. Select “24/7 LIFE BT Speaker”from the list of available Bluetooth
devices. If required enter password“0000”. If“24/7 LIFE BT
Speaker”does not appear in your device turn o the Bluetooth
function on your device then turn it back on.
5. Once paired successfully, you will hear a conrmation“Connected”
and the indicator light will be on solid.
Note 1: Once you have paired the speaker with a device, the speaker
will remember this device and will pair automatically when the
device’s Bluetooth is activated and in range.
Note 2: The speaker will attempt to automatically connect to the last
device it was paired with when switch on. If you want to pair it with
a new device, disconnect (unpair) the speaker from the previous
device and follow the steps outlined above.
Cover must be in place to
retain the speaker’s water
resistant feature.
8
8
Water Resistant
BC
WATER RESISTANT
WIRELESS SPEAKER Model: 160499
Warnings
Battery warning!
• ”Caution”– The battery used in the product may present a risk of re
or chemical burn if mistreated. Batteries may explode if damaged.
• Only recharge your battery with the provided approved cable
designated for the product.
• Dispose of batteries according to local regulations. Please recycle
when possible. Do not dispose the battery as household waste or in
a re as it may explode.
• The battery in your product can not be removed or replaced by the
user. Any attempt to do so is unsafe and may result in damage of
the product.
Built-in Battery Care:
• Your product is powered by a rechargeable battery. Optimal
performance of a new battery is achieved only after two or three
complete charge and discharge cycles. Do not leave a fully charged
battery connected to a charger, since overcharging may shorten its
lifetime.
• If left unused, a fully charged battery will lose its charge over time.
• Leaving the product in hot or cold places, such as in a closed car in
summer or winter conditions, will reduce the capacity and lifetime
of the battery.
• Always try to keep the battery between 32°F and 113°F. A product
may not work temporarily with an extremely hot or cold battery,
even when the battery is fully charged.
Important Safety Precautions
Read all instructions before using your Wireless Speaker.
• Never expose your product to high temperatures, extreme cold or
submerse in water.
• If the product overheats, has been dropped or damaged or has been
dropped in a liquid, discontinue use.
• In order to avoid the risk of electric shock, never attempt to open
your product or repair it, consult a certied professional.
• If you detect any abnormalities when using your product
immediately discontinue use and contact the manufacturer.
• Unplug your product when it will not be in use for long periods of
time or during lightning storms.
• Never mount or store the product over any airbag deployment area,
as serious injury may result when an airbag deploys.
• Do not dispose of product in heat or re.
• Do not clean the product with harmful chemicals or detergents.
Product Overview
Power
Mode
Indicator Light/Microphone
Volume
-
/ Previous Track
Volume + / Next Track
Auxiliary Audio Input Jack
Micro-USB Charging Port
Water Resistant Cover
1
2
3
5
6
7
IPX4 water resistance rating:
Wireless speaker is protected against
splashing water for a short period of time.
Note: The wireless speaker is NOT waterproof and can not be used
while swimming, showering or submerged in water.
Bluetooth® Connection (Pairing)
Bluetooth® Connection Trouble Shooting
Why won’t the wireless speaker connect to my device?
a. The Bluetooth setting on your device may have been turned o.
Turn on the Bluetooth function and search for“
24/7 LIFE BT
Speaker”
.
b.The wireless speaker may have been connected to another device.
Disconnect (unpair) the speaker from the previous device before
connecting it to your device.
c.The wireless speaker may not have been recognized by your device.
Turn o the wireless speaker then turn it back on. Search your
Bluetooth settings on your device and connect the wireless
speaker.
d.The wireless speaker may be to far away from the device to
connect. Make sure there are no obstacles between the devices
and reconnect the wireless speaker.
1 2 3 45
6 7
4
Turning On/O the Wireless Speaker
Turning On: Press and hold button for 2 seconds until indicator
light ashes and you hear“Power on, wireless mode”.
Note: If you have an aux cable plugged into the auxiliary audio input
jack you will hear“Power on, audio mode”.
Turning O: Press and hold button for 2 seconds until indicator
light turns o and you hear a“Power o”.
1. Turn on the wireless speaker by pressing and holding the
button for 2 seconds until indicator light ashes and you hear
“Power on, wireless mode”.
2. Place the wireless speaker and the Bluetooth device (phone) so
that they are no further than 3ft apart.
3. Activate the Bluetooth function on your Bluetooth device. (Refer
to the manufacturer’s instruction manual to enable Bluetooth on
your device).
4. Select “24/7 LIFE BT Speaker”from the list of available Bluetooth
devices. If required enter password“0000”. If“24/7 LIFE BT
Speaker”does not appear in your device turn o the Bluetooth
function on your device then turn it back on.
5. Once paired successfully, you will hear a conrmation“Connected”
and the indicator light will be on solid.
Note 1: Once you have paired the speaker with a device, the speaker
will remember this device and will pair automatically when the
device’s Bluetooth is activated and in range.
Note 2: The speaker will attempt to automatically connect to the last
device it was paired with when switch on. If you want to pair it with
a new device, disconnect (unpair) the speaker from the previous
device and follow the steps outlined above.
Cover must be in place to
retain the speaker’s water
resistant feature.
8
8
Water Resistant
BC
Hands Free Operation
Music Operation Charging Trouble Shooting
Specications
Product Covering Material: ABS plastic + Silicone + Fabric
Bluetooth Version: V5.0
Sound Output: 3W
Battery type: Li-ion
Battery Capacity: 800mAh
Charge Time: 2-3hours
Included Accessories: Charging cable and carabiner
Specications are subject to change without notice.
The wireless speaker has a built-in rechargeable battery. It is
recommended to fully charge the wireless speaker before using.
1. Use the provided cable to charge the wireless speaker from a
car/wall charger or from a computer’s USB port.
• Red indicator light on = charging
• Red indicator light o = fully charged
2. It takes approximately 2 to 3 hours to fully charge the wireless
speaker.
Why won’t the wireless speaker power on?
a. The wireless speaker’s batteries need to be recharged using the
charging cable.
Why isn’t the wireless speaker playing music?
a. The volume level on the wireless speaker is set at the minimum.
For best sound quality press the volume ”+”on the wireless
speaker until you hear a beep, then use your device to adjust the
volume to the desired level.
b. Make sure the wireless speaker is connect to the Bluetooth device.
You can control your music from your device by using the buttons on
the wireless speaker. Use the chart to control your music:
Function Operation
Volume Up Long press “+” button
Volume Down Long press “
-
” button
Previous Track Short press “
-
” button
Next Track Short press “+” button
Pause Short press“ ”button once
Play Short press“ ”button once
You can control phone calls from your Bluetooth device by using the
buttons on the wireless speaker. Use the chart to control your phone
calls:
Function Operation
Answer a Call Short press“ ”button once
End a Call Short press“ ”button once
“The Bluetooth® word mark and logos are registered trademarks
owned by Bluetooth SIG, Inc. and any use of such marks by [licensee
name] is under license. Other trademarks and trade names are those
of their respective owners.”
© Copyright 2019 SRP Companies 160499UM Rev. A 5-8
Recharge via USB Wall Charger:
Recharge via Computer’s USB Port:
M
M
Auxiliary Audio Input Jack
The Auxiliary Audio Input Jack allows you connect the output from
your audio player device such as your portable player, phone, etc to
your wireless speaker. When you plug a 3.5mm auxiliary audio cable
into the wireless speaker you will hear“Audio mode”.
Note: For best audio quality increase the volume level on the
wireless speaker to it’s maximum, then use the volume control on the
audio player device to adjust the volume to the desired level.
3.5mm Audio Cable
(not supplied)
Micro-USB Cable
(supplied)
Micro-USB Cable
(supplied)
Caution: Changes or modications not expressly approved by the
party responsible for compliance could void the user's authority to
operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1)This device may not
cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment o and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Information
Why isn’t the wireless speaker playing music?
The volume level on the wireless speaker is set at the minimum. For
best sound quality long press the volume ”+”on the wireless speaker
until you hear a beep, then use your device to adjust the volume to
the desired level.
M
M
Microphone
Note: If caller can’t hear you clearly speak directly into the
microphone.
Wall Charger
(not supplied)
Hands Free Operation
Music Operation Charging Trouble Shooting
Specications
Product Covering Material: ABS plastic + Silicone + Fabric
Bluetooth Version: V5.0
Sound Output: 3W
Battery type: Li-ion
Battery Capacity: 800mAh
Charge Time: 2-3hours
Included Accessories: Charging cable and carabiner
Specications are subject to change without notice.
The wireless speaker has a built-in rechargeable battery. It is
recommended to fully charge the wireless speaker before using.
1. Use the provided cable to charge the wireless speaker from a
car/wall charger or from a computer’s USB port.
• Red indicator light on = charging
• Red indicator light o = fully charged
2. It takes approximately 2 to 3 hours to fully charge the wireless
speaker.
Why won’t the wireless speaker power on?
a. The wireless speaker’s batteries need to be recharged using the
charging cable.
Why isn’t the wireless speaker playing music?
a. The volume level on the wireless speaker is set at the minimum.
For best sound quality press the volume ”+”on the wireless
speaker until you hear a beep, then use your device to adjust the
volume to the desired level.
b. Make sure the wireless speaker is connect to the Bluetooth device.
You can control your music from your device by using the buttons on
the wireless speaker. Use the chart to control your music:
Function Operation
Volume Up Long press “+” button
Volume Down Long press “
-
” button
Previous Track Short press “
-
” button
Next Track Short press “+” button
Pause Short press“ ”button once
Play Short press“ ”button once
You can control phone calls from your Bluetooth device by using the
buttons on the wireless speaker. Use the chart to control your phone
calls:
Function Operation
Answer a Call Short press“ ”button once
End a Call Short press“ ”button once
“The Bluetooth® word mark and logos are registered trademarks
owned by Bluetooth SIG, Inc. and any use of such marks by [licensee
name] is under license. Other trademarks and trade names are those
of their respective owners.”
© Copyright 2019 SRP Companies 160499UM Rev. A 5-8
Recharge via USB Wall Charger:
Recharge via Computer’s USB Port:
M
M
Auxiliary Audio Input Jack
The Auxiliary Audio Input Jack allows you connect the output from
your audio player device such as your portable player, phone, etc to
your wireless speaker. When you plug a 3.5mm auxiliary audio cable
into the wireless speaker you will hear“Audio mode”.
Note: For best audio quality increase the volume level on the
wireless speaker to it’s maximum, then use the volume control on the
audio player device to adjust the volume to the desired level.
3.5mm Audio Cable
(not supplied)
Micro-USB Cable
(supplied)
Micro-USB Cable
(supplied)
Caution: Changes or modications not expressly approved by the
party responsible for compliance could void the user's authority to
operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1)This device may not
cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment o and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Information
Why isn’t the wireless speaker playing music?
The volume level on the wireless speaker is set at the minimum. For
best sound quality long press the volume ”+”on the wireless speaker
until you hear a beep, then use your device to adjust the volume to
the desired level.
M
M
Microphone
Note: If caller can’t hear you clearly speak directly into the
microphone.
Wall Charger
(not supplied)
Hands Free Operation
Music Operation Charging Trouble Shooting
Specications
Product Covering Material: ABS plastic + Silicone + Fabric
Bluetooth Version: V5.0
Sound Output: 3W
Battery type: Li-ion
Battery Capacity: 800mAh
Charge Time: 2-3hours
Included Accessories: Charging cable and carabiner
Specications are subject to change without notice.
The wireless speaker has a built-in rechargeable battery. It is
recommended to fully charge the wireless speaker before using.
1. Use the provided cable to charge the wireless speaker from a
car/wall charger or from a computer’s USB port.
• Red indicator light on = charging
• Red indicator light o = fully charged
2. It takes approximately 2 to 3 hours to fully charge the wireless
speaker.
Why won’t the wireless speaker power on?
a. The wireless speaker’s batteries need to be recharged using the
charging cable.
Why isn’t the wireless speaker playing music?
a. The volume level on the wireless speaker is set at the minimum.
For best sound quality press the volume ”+”on the wireless
speaker until you hear a beep, then use your device to adjust the
volume to the desired level.
b. Make sure the wireless speaker is connect to the Bluetooth device.
You can control your music from your device by using the buttons on
the wireless speaker. Use the chart to control your music:
Function Operation
Volume Up Long press “+” button
Volume Down Long press “
-
” button
Previous Track Short press “
-
” button
Next Track Short press “+” button
Pause Short press“ ”button once
Play Short press“ ”button once
You can control phone calls from your Bluetooth device by using the
buttons on the wireless speaker. Use the chart to control your phone
calls:
Function Operation
Answer a Call Short press“ ”button once
End a Call Short press“ ”button once
“The Bluetooth® word mark and logos are registered trademarks
owned by Bluetooth SIG, Inc. and any use of such marks by [licensee
name] is under license. Other trademarks and trade names are those
of their respective owners.”
© Copyright 2019 SRP Companies 160499UM Rev. A 5-8
Recharge via USB Wall Charger:
Recharge via Computer’s USB Port:
M
M
Auxiliary Audio Input Jack
The Auxiliary Audio Input Jack allows you connect the output from
your audio player device such as your portable player, phone, etc to
your wireless speaker. When you plug a 3.5mm auxiliary audio cable
into the wireless speaker you will hear“Audio mode”.
Note: For best audio quality increase the volume level on the
wireless speaker to it’s maximum, then use the volume control on the
audio player device to adjust the volume to the desired level.
3.5mm Audio Cable
(not supplied)
Micro-USB Cable
(supplied)
Micro-USB Cable
(supplied)
Caution: Changes or modications not expressly approved by the
party responsible for compliance could void the user's authority to
operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1)This device may not
cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment o and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Information
Why isn’t the wireless speaker playing music?
The volume level on the wireless speaker is set at the minimum. For
best sound quality long press the volume ”+”on the wireless speaker
until you hear a beep, then use your device to adjust the volume to
the desired level.
M
M
Microphone
Note: If caller can’t hear you clearly speak directly into the
microphone.
Wall Charger
(not supplied)
Hands Free Operation
Music Operation Charging Trouble Shooting
Specications
Product Covering Material: ABS plastic + Silicone + Fabric
Bluetooth Version: V5.0
Sound Output: 3W
Battery type: Li-ion
Battery Capacity: 800mAh
Charge Time: 2-3hours
Included Accessories: Charging cable and carabiner
Specications are subject to change without notice.
The wireless speaker has a built-in rechargeable battery. It is
recommended to fully charge the wireless speaker before using.
1. Use the provided cable to charge the wireless speaker from a
car/wall charger or from a computer’s USB port.
• Red indicator light on = charging
• Red indicator light o = fully charged
2. It takes approximately 2 to 3 hours to fully charge the wireless
speaker.
Why won’t the wireless speaker power on?
a. The wireless speaker’s batteries need to be recharged using the
charging cable.
Why isn’t the wireless speaker playing music?
a. The volume level on the wireless speaker is set at the minimum.
For best sound quality press the volume ”+”on the wireless
speaker until you hear a beep, then use your device to adjust the
volume to the desired level.
b. Make sure the wireless speaker is connect to the Bluetooth device.
You can control your music from your device by using the buttons on
the wireless speaker. Use the chart to control your music:
Function Operation
Volume Up Long press “+” button
Volume Down Long press “
-
” button
Previous Track Short press “
-
” button
Next Track Short press “+” button
Pause Short press“ ”button once
Play Short press“ ”button once
You can control phone calls from your Bluetooth device by using the
buttons on the wireless speaker. Use the chart to control your phone
calls:
Function Operation
Answer a Call Short press“ ”button once
End a Call Short press“ ”button once
“The Bluetooth® word mark and logos are registered trademarks
owned by Bluetooth SIG, Inc. and any use of such marks by [licensee
name] is under license. Other trademarks and trade names are those
of their respective owners.”
© Copyright 2019 SRP Companies 160499UM Rev. A 5-8
Recharge via USB Wall Charger:
Recharge via Computer’s USB Port:
M
M
Auxiliary Audio Input Jack
The Auxiliary Audio Input Jack allows you connect the output from
your audio player device such as your portable player, phone, etc to
your wireless speaker. When you plug a 3.5mm auxiliary audio cable
into the wireless speaker you will hear“Audio mode”.
Note: For best audio quality increase the volume level on the
wireless speaker to it’s maximum, then use the volume control on the
audio player device to adjust the volume to the desired level.
3.5mm Audio Cable
(not supplied)
Micro-USB Cable
(supplied)
Micro-USB Cable
(supplied)
Caution: Changes or modications not expressly approved by the
party responsible for compliance could void the user's authority to
operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1)This device may not
cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment o and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Information
Why isn’t the wireless speaker playing music?
The volume level on the wireless speaker is set at the minimum. For
best sound quality long press the volume ”+”on the wireless speaker
until you hear a beep, then use your device to adjust the volume to
the desired level.
M
M
Microphone
Note: If caller can’t hear you clearly speak directly into the
microphone.
Wall Charger
(not supplied)
Hands Free Operation
Music Operation Charging Trouble Shooting
Specications
Product Covering Material: ABS plastic + Silicone + Fabric
Bluetooth Version: V5.0
Sound Output: 3W
Battery type: Li-ion
Battery Capacity: 800mAh
Charge Time: 2-3hours
Included Accessories: Charging cable and carabiner
Specications are subject to change without notice.
The wireless speaker has a built-in rechargeable battery. It is
recommended to fully charge the wireless speaker before using.
1. Use the provided cable to charge the wireless speaker from a
car/wall charger or from a computer’s USB port.
• Red indicator light on = charging
• Red indicator light o = fully charged
2. It takes approximately 2 to 3 hours to fully charge the wireless
speaker.
Why won’t the wireless speaker power on?
a. The wireless speaker’s batteries need to be recharged using the
charging cable.
Why isn’t the wireless speaker playing music?
a. The volume level on the wireless speaker is set at the minimum.
For best sound quality press the volume ”+”on the wireless
speaker until you hear a beep, then use your device to adjust the
volume to the desired level.
b. Make sure the wireless speaker is connect to the Bluetooth device.
You can control your music from your device by using the buttons on
the wireless speaker. Use the chart to control your music:
Function Operation
Volume Up Long press “+” button
Volume Down Long press “
-
” button
Previous Track Short press “
-
” button
Next Track Short press “+” button
Pause Short press“ ”button once
Play Short press“ ”button once
You can control phone calls from your Bluetooth device by using the
buttons on the wireless speaker. Use the chart to control your phone
calls:
Function Operation
Answer a Call Short press“ ”button once
End a Call Short press“ ”button once
“The Bluetooth® word mark and logos are registered trademarks
owned by Bluetooth SIG, Inc. and any use of such marks by [licensee
name] is under license. Other trademarks and trade names are those
of their respective owners.”
© Copyright 2019 SRP Companies 160499UM Rev. A 5-8
Recharge via USB Wall Charger:
Recharge via Computer’s USB Port:
M
M
Auxiliary Audio Input Jack
The Auxiliary Audio Input Jack allows you connect the output from
your audio player device such as your portable player, phone, etc to
your wireless speaker. When you plug a 3.5mm auxiliary audio cable
into the wireless speaker you will hear“Audio mode”.
Note: For best audio quality increase the volume level on the
wireless speaker to it’s maximum, then use the volume control on the
audio player device to adjust the volume to the desired level.
3.5mm Audio Cable
(not supplied)
Micro-USB Cable
(supplied)
Micro-USB Cable
(supplied)
Caution: Changes or modications not expressly approved by the
party responsible for compliance could void the user's authority to
operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1)This device may not
cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment o and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Information
Why isn’t the wireless speaker playing music?
The volume level on the wireless speaker is set at the minimum. For
best sound quality long press the volume ”+”on the wireless speaker
until you hear a beep, then use your device to adjust the volume to
the desired level.
M
M
Microphone
Note: If caller can’t hear you clearly speak directly into the
microphone.
Wall Charger
(not supplied)
Hands Free Operation
Music Operation Charging Trouble Shooting
Specications
Product Covering Material: ABS plastic + Silicone + Fabric
Bluetooth Version: V5.0
Sound Output: 3W
Battery type: Li-ion
Battery Capacity: 800mAh
Charge Time: 2-3hours
Included Accessories: Charging cable and carabiner
Specications are subject to change without notice.
The wireless speaker has a built-in rechargeable battery. It is
recommended to fully charge the wireless speaker before using.
1. Use the provided cable to charge the wireless speaker from a
car/wall charger or from a computer’s USB port.
• Red indicator light on = charging
• Red indicator light o = fully charged
2. It takes approximately 2 to 3 hours to fully charge the wireless
speaker.
Why won’t the wireless speaker power on?
a. The wireless speaker’s batteries need to be recharged using the
charging cable.
Why isn’t the wireless speaker playing music?
a. The volume level on the wireless speaker is set at the minimum.
For best sound quality press the volume ”+”on the wireless
speaker until you hear a beep, then use your device to adjust the
volume to the desired level.
b. Make sure the wireless speaker is connect to the Bluetooth device.
You can control your music from your device by using the buttons on
the wireless speaker. Use the chart to control your music:
Function Operation
Volume Up Long press “+” button
Volume Down Long press “
-
” button
Previous Track Short press “
-
” button
Next Track Short press “+” button
Pause Short press“ ”button once
Play Short press“ ”button once
You can control phone calls from your Bluetooth device by using the
buttons on the wireless speaker. Use the chart to control your phone
calls:
Function Operation
Answer a Call Short press“ ”button once
End a Call Short press“ ”button once
“The Bluetooth® word mark and logos are registered trademarks
owned by Bluetooth SIG, Inc. and any use of such marks by [licensee
name] is under license. Other trademarks and trade names are those
of their respective owners.”
© Copyright 2019 SRP Companies 160499UM Rev. A 5-8
Recharge via USB Wall Charger:
Recharge via Computer’s USB Port:
M
M
Auxiliary Audio Input Jack
The Auxiliary Audio Input Jack allows you connect the output from
your audio player device such as your portable player, phone, etc to
your wireless speaker. When you plug a 3.5mm auxiliary audio cable
into the wireless speaker you will hear“Audio mode”.
Note: For best audio quality increase the volume level on the
wireless speaker to it’s maximum, then use the volume control on the
audio player device to adjust the volume to the desired level.
3.5mm Audio Cable
(not supplied)
Micro-USB Cable
(supplied)
Micro-USB Cable
(supplied)
Caution: Changes or modications not expressly approved by the
party responsible for compliance could void the user's authority to
operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1)This device may not
cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment o and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Information
Why isn’t the wireless speaker playing music?
The volume level on the wireless speaker is set at the minimum. For
best sound quality long press the volume ”+”on the wireless speaker
until you hear a beep, then use your device to adjust the volume to
the desired level.
M
M
Microphone
Note: If caller can’t hear you clearly speak directly into the
microphone.
Wall Charger
(not supplied)
Table of contents
