Abbott IonicRF RF-POLE User manual

IonicRF™ Generator Pole Mount
Model RF-POLE
Instructions for
Use

CAUTION: Federal (USA) law restricts this device to sale by or on the order of
a physician.
™ Indicates a trademark of the Abbott group of companies.
‡ Indicates a third
-party trademark, which is property of its respective owner.
Pat.
http://www.abbott.com/patents
©
2020 Abbott. All Rights Reserved.

i
Contents
Intended Use.................................................................... 1
Warnings .......................................................................... 1
Precautions...................................................................... 2
Compatibility Guidelines.................................................... 2
Pole Mount Components................................................... 3
Preparing to Use the Pole Mount....................................... 4
Step 1: Attach the Pole Mount to the Roll Stand ...................... 4
Step 2: Remove the Countertop Stand..................................... 6
Step 3: Attach the Generator to the Pole Mount....................... 7
Cleaning Guidelines.......................................................... 9
Symbols and Definitions.................................................. 10
Additional Symbols for Product Labels............................. 11
Technical Support .......................................................... 12
Warranty Information ...................................................... 12

1
Intended Use
The IonicRF™ Generator Pole Mount (hereafter referred to as the
"pole mount") is an accessory that is intended to be used to secure
the IonicRF™ Generator to a compatible roll stand.
Warnings
The following warnings apply to these components:
Before attaching the generator, ensure the pole mount is
securely fastened to the roll stand. Failing to secure the pole
mount may cause the product to fall, resulting in product
damage or injury.
Before starting a procedure, ensure the generator is fastened
securely to the pole mount. Failing to secure the generator
may cause the product to fall, resulting in product damage or
injury.
When installed, ensure the top of the generator is no higher
than 139.7 cm (55 in) from the floor.
Do not mount, suspend, or place any item on the roll stand
other than the pole mount and generator.
The capacity of the tray should not exceed 2 kg (4.4 lb).
Pulling on the roll stand when the wheels are locked may
cause the roll stand to tip or fall, which may cause injury or
interrupt the procedure.

2
Precautions
The following precautions apply to these components:
Only use with roll stand model RD-0856.
Before moving the roll stand with the generator attached or
using the pole-mounted generator, ensure that any cables
attached to the generator will not become entangled with other
objects or present a tripping hazard.
Unlock the roll stand wheels before moving the pole-mounted
generator.
Compatibility Guidelines
Only the following products may be used with the
IonicRF™ Generator Pole Mount (model RF-POLE):
Product
Model Number
IonicRF™ Generator RFG-IONIC
Roll Stand RD-0856

3
Pole Mount Components
The following figure provides information about the pole mount
components.
Figure 1. Pole mount shown with compatible roll stand
Pole Mount
1. Pole mount clamp base
2. Captive thumb screws (4)
3. Pole mount clamp cap
4. Cap-head screws (2)
5. Hex drive screwdriver (5 mm)
Roll Stand (packaged separately)
6. Tray
7. Pole
8. Wheels (3 non-locking, 3 locking)

4
Preparing to Use the Pole Mount
The IonicRF™ Generator is portable and can be placed on a level
surface using the countertop stand or mounted to a compatible roll
stand using the IonicRF™ Generator Pole Mount.
To use the pole mount with the IonicRF Generator, follow these
three steps:
NOTE: This assembly requires two people.
Step 1: Attach the Pole Mount to the Roll
Stand
NOTE: The roll stand must be assembled before use. For
information about assembling the roll stand, refer to the
assembly instructions for that product.
Figure 2. Locking the wheels on the roll stand
1. Locked
2. Unlocked
1. Lock the wheels on the roll stand by pressing down on the
three black brakes.

5
Figure 3. Placing the pole mount on the pole
2. Slide the pole mount onto the pole until the top of the pole
mount clamp is below the bottom edge of the black pole cap.
NOTE: The top of the pole mount clamp should be
approximately 1.2 cm to 5.1 cm (0.5 in to 2 in) below the
bottom edge of the pole cap.

6
Figure 4. Tightening the cap-head screws
1. Top of pole mount
clamp placed
1.2 cm to 5.1 cm
(0.5 in to 2 in)
below the bottom
edge of the black
pole cap
3. Using the screwdriver included in the kit, tighten the cap-head
screws, alternating between the two, until the pole mount
clamp base is firmly attached to the clamp cap.
WARNING: Ensure the pole mount is securely fastened to
the pole before attaching the generator. Failing to secure
the pole mount may cause the product to fall, resulting in
product damage or injury.
Step 2: Remove the Countertop Stand
NOTE: The IonicRF™ Generator is supplied with an attached
countertop stand. Before attaching the pole mount to the
generator, the countertop stand must be removed. Always
place the generator on a level surface when adding or
removing the countertop stand.

7
Figure 5. Removing the countertop stand from the generator
1. Using your fingers, fully loosen each of the four captive thumb
screws on the countertop stand until they can be removed
from the generator.
2. Remove the stand from the generator.
Step 3: Attach the Generator to the Pole
Mount
NOTE: Attaching the generator requires two people—one to
hold the generator in position and one to attach the generator.
1. Person 1: Lock the wheels on the roll stand.
2. Person 1: Ensure that the pole mount is fastened securely to
the pole.

8
Figure 6. Aligning the screw holes with the captive thumb screws
1. Generator
2. Pole mount
3. Pole
4. Screw holes
5. Captive thumb
screws
3. Person 1: Hold the generator in place.
Person 2: Align the four screw holes on the back of the
generator with the captive thumb screws on the pole mount.

9
Figure 7. Fastening the generator
4. Person 2: Thread each of the four captive thumb screws until
all are engaged.
5. Person 2: Hand tighten each of the four captive thumb screws
until the generator is fastened securely.
Cleaning Guidelines
To clean the pole mount, use any of the following:
A cotton cloth soaked with 99% isopropyl alcohol
Sani-Cloth‡ AF3 Germicidal Disposable Wipes
For information about cleaning the generator or roll stand, refer to
the instructions for use for the appropriate product.

10
Symbols and Definitions
The following symbols may be used in this document and on some
of the products and packaging:
Symbol
Definition
Follow the instructions for use
Consult instructions for use
Consult instructions for use on this website
Installation requires two people
Safe working load
Date of manufacture
Do not use if package is damaged
Catalog number
Manufacturer
Contents quantity
Lot number

11
Symbol
Definition
Unique Device Identification
Prescription use only
Authorized European representative
European Conformity. Affixed in accordance with
European Council Directive 93/42/EEC as
amended by 2007/47/EC. Hereby, Abbott
Medical declares that this device is in
compliance with the essential requirements and
other relevant provisions of this directive.
Additional Symbols for Product Labels
The following table shows additional symbols that may appear on
the product labels for parts related to this kit.
Symbol
Description
Generator Pole Mount

12
Technical Support
For technical questions and support for your product, use the
following information:
[phone] (toll-free within North America)
[phone]
For additional assistance, call your local Abbott Medical
representative.
Warranty Information
See product packaging and relevant commercial agreements for
specific warranty information.

Abbott Medical
5050 Nathan Lane North
Plymouth, MN 55442 USA
[phone]
[phone]
Abbott Medical
The Corporate Village
Da Vincilaan 11 Box F1
1935 Zaventem
Belgium
[phone]
2020-10
ARTEN600061613 B