Abram's Nation The Safety Sleeper Manual

[phone] | [e-mail] | safetysleeper.com
V2.5 Updated: 05/18/2021
Patent: US 7,971,596 B2
Assembly & User Manual
WARNINGS!
Always follow assembly instructions Coverlet safety sheet must be used at
all times to prevent entrapment
Only use the recommended size
mattress: see technical specs
Maximum weight (occupant) : single
450lb/204kg

1..........................................
2...........................................................................................
3...........................................................................................
4...............................................................
5................................................................
6......................................................
7......................................................
8.......................................
9.......................................
10..................................................
11...................................................
12..................................................................
13..............
14............................................................................
15......................................................................................
16.....................................
17.................................................................
[phone] | [e-mail] | safetysleeper.com
TABLE OF CONTENTS
Washing and Handling Instructions
Disclaimer
Disclaimer
Technical Specifications
Technical Specifications
Assemble Twin/Single Frame
Assemble Twin/Single Frame
Assemble Full/Double/Queen Frame
Assemble Full/Double/Queen Frame
Attaching Enclosure to Frame
Attaching Enclosure to Frame
Inserting the Mattress
Adding and Removing the Coverlet Safety Sheet
Suitcase Packing
Air Mattress
Regulations and Testing Compliance
Important Information

Do not use fabric softener
[phone] | [e-mail] | safetysleeper.com 1
WASHING & HANDLING INSTRUCTIONS
WASHING INSTRUCTIONS
Wash cold or warm on gentle
Machine wash on delicate cycle in either a front loading washing
machine or a top-loading machine without a center agitator. Use
only laundry detergent and/or vinegar. All zippers must be
closed before washing. Entire enclosure, frame pads, and
coverlet safety sheet can be washed.
Use vinegar
DRYING INSTRUCTIONS
Tumble dry The Safety Sleeper® on low heat, or line dry.
Dry on low heat
Dry on gentle
Line dry
Do not iron
Use laundry detergent
Find The Safety Sleeper® instructional
videos on assembly and care at:
safetysleeper.com/pages/assembly
Or scan the QR Code.
PRIOR TO USE WASH THE ENCLOSURE AND COVERLET
SAFETY SHEETS.
Do not bleach
Do not dry clean

[phone] | [e-mail] | safetysleeper.com 2
DISCLAIMER
RECOMMENDED USE
For proper use, care and assembly, all instructions must be
specically adhered to. Wash before rst use of this product. Bed
is not intended for use as a toy, play equipment or as a disciplinary
device. Recommended for ages 3 and up.
ENTRAPMENT HAZARD
Pillows, blankets, and stu󰀨ed animals to be used at caregiver’s
discretion. Coverlet safefy sheet must be used at all times to
reduce the risk of serious injury from entrapment between the
mattress and bed enclosure.
Abram’s Nation is not responsible for any accidents or injuries
that could occur if this product is used for purposes not
intended.

[phone] | [e-mail] | safetysleeper.com 3
DISCLAIMER
Read and follow instructions before assembly and use.
Save this manual for future reference. If you do not have
instructions, do not use this product. Contact Abram’s Nation
at [e-mail],[phone] or visit
www.safetysleeper.com
PROPER USE
• Periodically inspect enclosure (wear, tear, loose stitching, and
zippers) and frame (worn, bent, broken frame pieces and/or spring
pins) for any damage that could compromise the safe usage of the
product. If there is signicant damage please contact our customer
support to start the repair process.
• In order to reduce the risk of tipping, use provided stabilizing
straps to secure the enclosure and frame to the underlying standard
wooden or metal bed frame (not included).
• Ensure your in-home mattress (when applicable) meets safety
guidelines (https://sleepproducts.org/advocacy/federal-mattress-
regulations/).
IMPROPER USE
• Do not use the The Safety Sleeper® if any parts are missing
or broken. Contact Abram’s Nation for replacement parts and
instructional literature if needed.
• Do not substitute parts.
• Do not alter the enclosure. Repairs should only be done by
Abram’s Nation or authorized distributors. Contact Abram’s Nation
for more information.
• Do not climb on top of the enclosure.

[phone] | [e-mail] | safetysleeper.com 4
107.25cm/42.23”
188cm/74”
TECHNICAL SPECIFICATIONS
Size Length Width
US Twin
EU Single
AU Single
107.32cm/42.25”
107.25cm/42.23”
107.25cm/42.23”
189.23cm/74.5”
200cm/78.75”
188cm/74”
105.41cm/41.5”
97.8cm/38.5”
99.7cm/39.25”
EXTERIOR OVERALL DIMENSIONS
US Full
EU Double
AU Double
107.25cm/42.23”
189.23cm/74.5”
200cm/78.75”
143.51cm/56.5”
147.8cm/51.8”
146cm/57.5”
US Queen 107.32cm/44.25”
201.93cm/79.5” 158.75cm/62.5”
UK Single 107.25cm/42.23”
189.2cm/74.5” 97.8cm/38.5”
UK Double 143.5cm/56.5”
US Twin XL 201.93cm/79.5” 105.41cm/41.5”
MATTRESS DIMENSIONS
Size Height
Length Width
US Twin
EU Single
AU Single
20.5-25.5cm/8-10”
19-24cm/7.5-9.5”
189.23cm/74.5”
200cm/ 78.74”
188cm/74”
96.52/38”
90cm/35.43”
92cm/36.22”
US Full
EU Double
AU Double
19-24cm/7.5-9.5”
189.23cm/74.5”
200cm/ 78.74”
188cm/74”
134.62cm/53”
140cm/55.12”
138cm/54.33”
US Queen 203.2cm/80” 149.86cm/59”
UK Single 190cm/74.8” 90cm/35.43”
UK Double 190cm/74.8” 135cm/ 53.15”
US Twin XL 201.93cm/79.5” 96.52cm/38”
107.25cm/42.23”
189.2cm/74.5”
112.40cm/44.25”
Height
107.32cm/42.25”
20.5-25.5cm/8-10”
20.5-25.5cm/8-10”
20.5-25.5cm/8-10”
20.5-25.5cm/8-10”
20.5-25.5cm/8-10”
20.5-25.5cm/8-10”
20.5-25.5cm/8-10”

[phone] | [e-mail] | safetysleeper.com 5
OPERATING CONDITIONS
The Safety Sleeper® is designed for normal indoor conditions.
WEIGHT
Shipping: Total product weight with suitcase: under 50lbs/23kg
*excluding queen which is approximately 55lbs/25kg
Occupant maximum weight/load: 450 lbs (204 kg)
MATERIALS
Fabric & Mesh:100% Polyester Material Flame Resistant
Bias Binding: 50% Cotton/50% Polyester
Webbing: 100% Polypropylene
YKK Zippers
FRAME
Aluminum
Nylon
Stainless Steel
TECHNICAL SPECIFICATIONS

[phone] | [e-mail] | safetysleeper.com 6
Assembly videos also available at:
safetysleeper.com/pages/assembly
ASSEMBLE TWIN/SINGLE FRAME
STEP 3: Connect the B4 pieces to each other rst, then align
the B5 & B6 frame piece across from each other and connect to
their counterparts at the same time to ensure they snap together
properly.
STEP 1: Lay all six pieces labeled B1, B2, B3, B4, B5, B6 on the
ground with labels facing up.
STEP 2: Connect B1 to B1, B2 to B2, and B3 to B3 in numerical
order by pushing in button & sliding together until button clicks into
place.
B5 B5
B4
B4
B6 B6
B5 B5
B6 B6
B4

[phone] | [e-mail] | safetysleeper.com 7
ASSEMBLE TWIN/SINGLE FRAME
STEP 4: Lay out four top frame pieces labeled T1, T2, T3, then
connect by pushing in button and sliding together until button clicks
into place.
STEP 5: Repeat for second top support using pieces with T4, T5, T6.
STEP 6: Hold the T1-T3 vertically and line it up with the B2-B3 base
piece making sure support pieces are facing towards the center of the
frame and match the correct jaw slide (S1 to S1, S2 to S2). Line up
each connection point so that push pin/spring pin can slide through
and then ip push pin toggles to secure the top pieces to the base.
Secure the support pieces the same way. Repeat with the other side.
NOTE: To release the push pins, push the head of the pin, align the
toggle horizontally, and pull out.
Push Pin/
Spring Pin
Jaw Slide
T3 T3
T1
T1
T2 T2
T3
T1
T2
T5 T5
T4
T4
T6 T6
T4
T5
T6

[phone] | [e-mail] | safetysleeper.com 8
ASSEMBLE FULL/DOUBLE/QUEEN FRAME
STEP 1: Lay all eight pieces labeled B1, B2, B3, B4, B5, B6, B7, B8
on the ground with labels facing up.
STEP 2: Connect B1 to B1, B2 to B2, B3 to B3 and B4 to B4 in
numerical order by pushing in button & sliding together until button
clicks into place.
STEP 3: Connect the B5 to B5, B6 to B6, then align B7 and B8
frame pieces frame piece across from each other and connect to
their counterparts at the same time to ensure they snap together
properly.

[phone] | [e-mail] | safetysleeper.com 9
ASSEMBLE FULL/DOUBLE/QUEEN FRAME
STEP 1: Lay out ve top frame pieces labeled T1, T2, T3, T4 then
connect by pushing in button and sliding together until button clicks
into place.
STEP 2: Repeat for second top support using pieces with T5, T6,
T7, T8
STEP 3: Hold the T1-T4 vertically and line it up with the B3-B4 base
piece making sure support pieces are facing towards the center of
the frame and match the correct jaw slide (S1 to S1, S2 to S2). Line
up each connection point so that push pin can slide through and then
ip push pin toggles to secure the top pieces to the base. Secure the
support pieces the same way. Repeat with the other side.
NOTE: To release the push pins, push the head of the pin, align the
toggle horizontally, and pull out.
Push Pin/
Spring Pin
Jaw Slide

[phone] | [e-mail] | safetysleeper.com 10
STEP 1: Attach the frame pad
covers so they cover the push
pins. Zipper goes on vertical bar.
TIP: Ensure pin is fully engaged
into the box before zipping.
*Frame pads can be installed
before or after inserting the
mattress.*
ATTACHING TO FRAME
Zipper

[phone] | [e-mail] | safetysleeper.com 11
STEP 3: Attach the enclosure to the base frame at the head and
foot, or B1 and B4 (Twin/Single) or B1/B2 and B5/B6 (Full/Queen/
Double). Using the zipper tab under the enclosure.
STEP 2: Lay enclosure with roof
zippers facing up, on the inside
base of the frame.
STEP 5: Repeat step ve for the
other side of the frame.
STEP 4: Lift one side of the
enclosure to the top frame, then
attach the enclosure to the frame
by wrapping the padding around
the frame and securing it with the
zipper.
ATTACHING TO FRAME

[phone] | [e-mail] | safetysleeper.com 12
INSERTING THE MATTRESS
STEP 2: Close the Zipper around
the end of the mattress. Secure
zipper pull tab into swivel locking
clip. *Check that the zippers for
both mattress entry points are
secured into the swivel locking clip.
STEP 1: Unzip one or both of the
mattress pockets on either end of
the enclosure.
Swivel locking clip
For daily home use a standard 8” waterproof memory foam
mattress is provided (US & Can). Any 8-10” standard mattress can
be used inside of The Safety Sleeper. Air mattress is for travel
use only.
STEP 3: Although the bed may
be used directly on the oor, for
added stability we recommend
placing it on a bed frame (with or
without a box spring) and using
the provided stabilizing straps to
secure The Safety Sleeper® frame
to the bed frame.
*photo shown with frame for
visualization purposes only.

[phone] | [e-mail] | safetysleeper.com 13
ADDING AND REMOVING THE COVERLET
SAFETY SHEET
The Safety Sleeper® utilizes a coverlet safety sheet design that
creates a completely enclosed pocket for the mattress. The coverlet
safety sheet can easily be removed and laundered (for more, see
the “Washing and Care Instructions”).
WARNING: A Coverlet Safety Sheet must be used at all
times to avoid risk of entrapment between the mattress
and the enclosure.
REMOVECHANGE COVERLET
SAFETY SHEET
STEP 2: Detach Velcro lock and start to unzip
coverlet safety sheet. Pass zipper up through so it
can be accessed from the top of the coverlet safety
sheet (from inside of the enclosure).
STEP 3: Open the door of the bed to give yourself more access
and continue unzipping the coverlet safety sheet from around the
mattress until coverlet safety sheet is separated completely. (Do this
process in reverse to reattach coverlet safety sheet.)
Ensure the pin is completely engaged in the
box before zipping.
Coverlet Safety
Sheet Zipper
STEP 1: Unzip the mattress
pocket directly below The Safety
Sleeper® tag to gain access to the
coverlet safety sheet zipper.
REATTACHING COVERLET SAFETY SHEET

[phone] | [e-mail] | safetysleeper.com 14
SUITCASE PACKING
The Safety Sleeper® is designed for travel and daily use.
Below is our recommended method for packing the
suitcase.
1. Lay triangular frame pads on left side.
2. Place folded enclosure over the frame
pads.
3. Pack right angle pieces from base frame.
4. Pack double 45 degree angle pieces from
top metal frame.
5. Pack straight pieces angled between
corners.
6. Pack the air mattress, extra coverlet safety
sheet, and stabilization straps on top.

[phone] | [e-mail] | safetysleeper.com 15
AIR MATTRESS
Air mattress is intended for travel use only.
The following safety tips are provided by the air mattress’s
manufacturer.
Air Mattress Safety Tips
1. Stretching is a natural characteristic of new vinyl. During initial
use, your airbed may become soft and require additional ination
to maintain desired rmness. This is normal for the rst few days
of use.
2. Always keep your airbed fully inated when in use. Do not over
inate.
3. Keep the airbed away from stairs, windows and sharp,
breakable objects.
4. Never stand, walk or jump on your airbed.
5. Always keep the ocked side of the mattress up.
6. Do not leave built in pumps plugged in while inside of the
enclosure.
7. Follow the above guidelines to avoid entrapment, serious
injury or property damage.
8. Clean your airbed with mild soapy solution. Do not use
chemicals.

[phone] | [e-mail] | safetysleeper.com 16
The Safety Sleeper uses medical grade flame retardant
fabrics and is subject to and compliant with the
following regulations.
• FDA Registered Medical Device
• Operator: 10049434
• Registration: 3011389091
• Listing: D234571
• Regulation (EU) 2017/745
• EN 12182:2012
• EN 1021-1/-2
• General Product Safety Directive 2001/95/EC
• Prop 65 Compliant (nothing that requires warnings)
• REACH Regulation 1907/2006/EC
Regulation on Persistent Organic Pollutants 850/2004/EC
Made in Pennsylvania, USA.
European Representative:
Murray’s Medical Equipment Ltd, Airton Road,
Tallaght, Dublin 24, Ireland. DL: 00 353 (0) 1 866 3333
REGULATIONS AND TESTING COMPLIANCE

The Safety Sleeper®
Information for your records
Serial # _______________________________________________
Date you received your bed ______________________________
Purchased by (DME/Non-prot) ____________________________
IMPORTANT INFORMATION
Staple your receipt to this manual for easy reference
[phone] | [e-mail] | safetysleeper.com 17
Find The Safety Sleeper® warranty
activation at:
safetysleeper.com/pages/warranty-
activation
Or scan the QR Code.

[phone] | [e-mail] | safetysleeper.com
4726 Highpoint Drive
Gibsonia, PA 15044