Abram's Nation The Safety Sleeper Manual

1
The Safety Sleeper®
Assembly & User Manual
(Twin & Single)
ALWAYS follow assembly instructions Coverlet must be used at ALL times to
prevent entrapment or suffocation.
Use ONLY the recommended size
mattress: See Technical Specs Maximum weight: 300 lbs.
Sll have quesons or require an alternate format due to visual,
reading, or cognive disabilies?
Call [phone] or email—customercare@abramsnaon.com
WARNINGS
The Safety Sleeper® is manufactured in the United States and distributed glob-
ally by Abram’s Naon, LLC. The Safety Sleeper® was designed with the inten-
on of addressing certain sleep wandering and security complicaons associ-
ated with various disabilies, including, but not limited to Angelman Syn-
drome, Ausm and Smith-Magenis Syndrome.
V2.4 Updated: 09/24/2019
Patent: US 7,971,596 B2

2
Table of Contents
1. TECHNICAL SPECIFICATIONS ………………………………………………………………... 04
2. DURABILITY …………………………………………………………………………………………. 05
3. ASSEMBLE FRAME BASE ………………………………………………………………………. 06
4. ASSEMBLE TOP FRAME ………………………………………………………………………… 07
5. ATTACHING ENCLOSURE TO FRAME …………………………………………………….. 08
6. INSERTING THE MATTRESS (TWIN) ………………………………………………………. 09
7. ADDING AND REMOVING THE COVERLET .…………………………………………… 10
8. WASHING & HANDLING INSTRUCTIONS .……………………………………………… 11
9. SUITCASE PACKING INSTRUCTIONS ……………………………………………………… 12
10. AIR MATTRESS SAFETY ………………………………………………………………………… 13
11. REGULATIONS AND TESTING COMPLIANCE..………………………………………… 14

3
FAILURE TO FOLLOW THESE WARNINGS AND THE INSTRUCTIONS COULD RESULT IN SERIOUS
INJURY OR DEATH
 Read and follow instrucons before assembly and use. SAVE THIS MANUAL FOR FUTURE
REFERENCE. If you do not have instrucons, DO NOT use this product. Contact Abram’s Na-
on via customercare@abramsnaon.com, 724-96-SLEEP or visit
hps://www.abramsnaon.com/
 Periodically inspect enclosure (wear, tear, loose stching, and zippers) and frame (wear,
bent or broken frame pieces, broken spring pins, sharp edges, or corrosion) for any damage
that could compromise the safe usage of the product. If there is signicant damage please
contact our customer support to start repair process.
 DO NOT use the The Safety Sleeper® if any parts are missing or broken. Contact or write
Abram’s Naon for replacement parts and instruconal literature if needed. DO NOT subs-
tute parts.
 DO NOT alter the enclosure. Repairs should be done by Abram's Naon or distributors.
 DO NOT climb on top of the enclosure.
 In order to reduce the risk of pping, use provided stability straps to secure the enclose and
frame to the underlying standard wooden or metal bed frame (not included).
 Non-re retardant pillows, blankets, and stued animal are NOT recommended for this
product as they reduce the ame protecon it provides.
 Ensure your in-home maress (not provided) meets safety guidelines
(hps://sleepproducts.org/advocacy/federal-maress-regulaons/)
ENTRAPMENT AND SUFFOCATION HAZARD
Coverlet must be used at ALL mes to reduce the risk of serious injury or death from entrap-
ment or suocaon between the maress and bed enclosure.
WARNINGS

4
TECHNICAL SPECIFICATIONS
Operang Condions: The Safety Sleeper® is designed for normal indoor condions.
Storage Condions: The Safety Sleeper® should be stored in the provided suitcase
(30x18x12”) in ambient warehouse temperatures (15° to 25°C, or 59° to 77°F) at normal hu-
midity levels. Avoid excess moisture or high humidity that may damage product materials.
Size Height Length Width
Twin 42” (107cm) 75” (190.5cm) 40” (102cm)
EU Single 107cm 200cm 94cm
AU/UK Single 107cm 190cm 94cm
Size Height Length Width
Twin 8-10” 75” (190.5cm) 40” (102cm)
EU Single 19-22cm 200cm 90cm
AU/UK Single 22-27cm 188-190cm 90-92cm
Enclosure & Frame Dimensions
Weight
Total weight including suitcase & air maress:
Twin/Singles: 38 lbs (17.25 kg)
Maximum weight/load: 300 lbs (136 kg)
Maress Dimensions

5
The Safety Sleeper® is made of high quality, medical grade fabrics and aluminum and has an
expected product life of at least 5 years.
Materials
Fabric & Mesh:100% Polyester Material Flame Resistant
Bias Binding: 50% Coon/50% Polyester
Webbing: 100% Polypropylene
Enclosure and door zippers: YKK #8
Coverlet zippers: YKK #5
LIFTING OR REMOVING THE ENCLOSURE
CAUTION: Remove the regular maress enrely before liing or moving the enclosure.
Even if the maress is removed or only the air maress is inside, we recommend liing with
two people grabbing the boom of the frame. If only a single person is available to li the
frame, they should do so by holding the middle of the vercal uprights close to the plane of
their body while keeping the boom of the frame supported against their leg(s).
Durability:
Frame
7/8” diameter aluminum
Connectors ¾ inch diameter
Fabric Strength
Mesh 250 psi
Enclosure: 300 psi
Coverlet: 100 psi

6
6
ASSEMBLE FRAME BASE
STEP 1: Lay all six pieces labeled B1, B2, B3, B4, B5, B6 on the ground with labels facing up.
STEP 2: Connect B1 to B1, B2 to B2, and B3 to B3 in numerical order by pushing in buon &
sliding together unl buon clicks into place.
STEP 3: Connect the B4 pieces to each other rst, then align the B5 & B6 frame piece across
from each other and connect to their counterparts at the same me to ensure they snap to-
gether properly.
Assembly video also available at
hps://www.abramsnaon.com/informaonal-downloads/assembly-disassembly/

7
ASSEMBLE TOP FRAME
STEP 1: Lay out four top frame pieces labeled T1, T2, T3, then connect by pushing in buon &
sliding together unl buon clicks into place.
STEP 2: Repeat for second top support using pieces with T4, T5, T6.
STEP 3: Hold the T1-T3 vercally and line it up with the B2-B3 base piece making sure support
pieces are facing towards the center of the frame and match the correct jaw slide (S1 to S1, S2
to S2). Line up each connecon point so that push pin can slide through and then ip push pin
toggles to secure the top pieces to the base. Secure the support pieces the same way. Repeat
with the other side.
NOTE: To release the push pins, push the head of the pin, align the toggle (horizontally), &
pull out.
7

8
ATTACHING ENCLOSURE TO FRAME
STEP 1: Although the bed may be used directly on the
oor, for added stability we recommend placing it on a
bed frame (with or without a box spring) and using the
provided stabilizaon straps to secure The Safety
Sleeper frame to the bed frame.
this aer the maress is installed.
STEP 2: Lay enclosure with roof zippers facing up,
inside base of the frame.
STEP 3: Li the top of the enclosure to the outer
side of the frame and wrap the side of the zipper
around the top horizontal bar of frame & zip all
the way across to secure.
STEP 4: Repeat step three for the other side of
the frame.
9
STEP 4: Aach frame pad covers to the frame sides so that
the triangle boom covers the padding and push pins.
TIP: When zipping the frame pad, hold it 2-3 inches higher
up the pole, and then, once fully zipped, slide them the rest
of the way down over the foam padding and push pins.

9
INSERTING THE MATTRESS (TWIN)
For regular use in the home, your Safety Sleeper is intended to work with a standard 10” tall
twin maress (not provided). We provide an air maress and suitcase for use when traveling.
STEP 3: Close the Zipper around the end of
the maress.
STEP 1: Unzip one of the maress pockets on
either end of the enclosure
STEP 2: Slide the maress in.
HOME
In the home, The Safety Sleeper® is intended for use with a standard maress (not included)
that is within the height parameters below.
US Twin: Regular 8-10” tall twin maress
Australian & UK Single: Regular 22-27cm tall single maress
EU Single: Regular 22cm tall single maress
TRAVEL
Provided air maress and built-in (US) or baery powered (Internaonal) pump.

10
ADDING AND REMOVING THE COVERLET
The Safety Sleeper ulizes a coverlet design that creates a completely enclosed pocket for the
maress. The coverlet can easily be swapped out and washed (for more, see the “Washing and
Care Instrucons”).
WARNING: A Coverlet must be used at all mes to avoid risk of entrapment between the
maress and the enclosure.
REATTACHING COVERLET: Start by sliding the pin (on the enclosure half of the zipper) through
the zipper pull and into the box on the coverlet zipper half, then repeat the process above in
reverse.
Remove/Change Coverlet:
STEP 1: Unzip the maress pocket directly below The
Safety Sleeper tag to gain access to the coverlet zipper.
STEP 2: Detach Velcro lock and start to unzip coverlet.
Pass zipper up through so it can be accessed from the
top of the coverlet (from inside of the enclosure).
STEP 3: Open the door of the bed to give yourself more access & connue unzipping the cov-
erlet from around the maress unl coverlet is separated completely. (Do this process in re-
verse to reaach coverlet.)

11
WASHING & HANDLING INSTRUCTIONS
WASH BEFORE FIRST USE
Materials
Fabric & Mesh:100% Polyester Material Flame Resistant.
Bias Binding 50% Coon/50% Polyester.
Webbing: 100% Polypropylene.
Washing Instrucons
DO NOT USE FABRIC SOFTENER
DO NOT USE BLEACH
DO NOT IRON
DO NOT DRY CLEAN
Machine wash on delicate cycle in either a front loading washing machine or a top-loading
machine without a center agitator. All ZIPPERS must be CLOSED before washing.
Tumble dry low heat only or line dry.
DISCLAIMER: For proper use, care & assembly, all instrucons must be specically adhered to.
Wash before rst use of this product. Bed is not intended for use as a toy, play equipment or
as a disciplinary device. Recommended for ages 3 and up.

12
SUITCASE PACKING INSTRUCTIONS
The Safety Sleeper® is designed to also travel and comes with a suitcase and air maress.
Below is our recommended method for packing the suitcase.
1. Lay triangular frame pads on le side.
2. Carefully place folded enclosure over the frame pads.
3. Pack Right Angle Curves from Base.
4. Pack Double 45 Degree Angle Curves from Top Metal
Frame
5. Pack Straight Pieces Angled Between Corners
6. Pack frame straps and air maress and secure with
the elasc suitcase straps

13
SUITCASE PACKING INSTRUCTIONS
The provided air maress is intended only for use within a secured coverlet and a fully zipped
maress pocket zipper.
The following safety ps are provided by the air maress’s manufacturer.
Air Maress Safety Tips
1. Always keep your airbed fully inated when in use.
2. Never use an airbed in water.
3. Keep your airbed away from re.
4. Do not use ammable substances (like aerosol re repair products) with your airbed.
The maress may ignite or explode.
5. Keep the airbed away from stairs, windows and sharp, breakable objects.
6. Never stand, walk or jump on your airbed.
7. Always supervise children around airbeds.
8. Inate only with a low-pressure inator. Do not over inate.
9. Stretching is a natural characterisc of new vinyl. During inial use, your airbed may be
come so and require addional inaon to maintain desired rmness. This is normal
for the rst few days of use.
10. Clean your airbed with mild soapy soluon. Do not use chemicals.
11. Use PVC glue and patches to repair.
12. Always keep the ocked side of the maress up.
13. Do not leave built in pumps plugged in while inside of the enclosure.
14. Follow the above guidelines to avoid entrapment, suocaon, serious injury or property
damage.

14
Regulaons and Tesng Compliance
The Safety Sleeper® uses medical grade ame retardant fabrics and is subject to and
compliant with the following regulaons.
 FDA Registered Medical Device
 Operator: 10048434
 Registraon: 3011389091
 Lisng: D234571
 CE Marked
 EN 12182:2012
 EN 1021-1/-2
 General Product Safety Direcve 2001/95/EC
 Prop 65 Compliant (nothing that requires warnings)
 REACH Regulaon 1907/2006/EC
 Regulaon on Persistent Organic Pollutants 850/2004/EC

15

16
4726 Highpoint Drive
Gibsonia, PA 15044 USA
abramsnation.com
Unique Solutions for Special Families
4726 Highpoint Drive
Gibsonia, PA 15044 USA
abramsnation.com
Unique Solutions for Special Families

1
The Safety Sleeper®
Assembly & User Manual
(Full, Double, & Queen)
ALWAYS follow assembly instructions Coverlet must be used at ALL times to
Use ONLY the recommended size Maximum weight: 300 lbs.
Sll have quesons or require an alternate format due to visual,
reading, or cognive disabilies?
Call [phone] or email—customercare@abramsnaon.com
WARNINGS
The Safety Sleeper® is manufactured in the United States and distributed glob-
ally by Abram’s Naon, LLC. The Safety Sleeper® was designed with the inten-
on of addressing certain sleep wandering and security complicaons associ-
ated with various disabilies, including, but not limited to Angelman Syn-
drome, Ausm and Smith-Magenis Syndrome.
V2.5 Updated: 09/25/2019
Patent: US 7,971,596 B2

2
Table of Contents
1. TECHNICAL SPECIFICATIONS ………………………………………………………………... 04
2. DURABILITY …………………………………………………………………………………………. 05
3. ASSEMBLE FRAME BASE ………………………………………………………………………. 06
4. ASSEMBLE TOP FRAME ………………………………………………………………………… 07
5. ASSEMBLING FRAME PADDING ……………………………………………………………. 08
6. ATTACHING ENCLOSURE TO FRAME …………………………………………………….. 09
7. INSERTING THE MATTRESS (TWIN) ………………………………………………………. 10
8. ADDING AND REMOVING THE COVERLET .……………………………………………. 11
9. WASHING & HANDLING INSTRUCTIONS .……………………………………………… 12
10. SUITCASE PACKING INSTRUCTIONS ……………………………………………………… 13
11. AIR MATTRESS SAFETY …………………………………………………………………………. 14
12. REGULATIONS AND TESTING COMPLIANCE..…………………………………………. 15

3
FAILURE TO FOLLOW THESE WARNINGS AND THE INSTRUCTIONS COULD RESULT IN SERIOUS
INJURY OR DEATH
 Read and follow instrucons before assembly and use. SAVE THIS MANUAL FOR FUTURE
REFERENCE. If you do not have instrucons, DO NOT use this product. Contact Abram’s Na-
on via customercare@abramsnaon.com, 724-96-SLEEP or visit
hps://www.abramsnaon.com/
 Periodically inspect enclosure (wear, tear, loose stching, and zippers) and frame (wear,
bent or broken frame pieces, broken spring pins, sharp edges, or corrosion) for any damage
that could compromise the safe usage of the product. If there is signicant damage please
contact our customer support to start repair process.
 DO NOT use the The Safety Sleeper® if any parts are missing or broken. Contact or write
Abram’s Naon for replacement parts and instruconal literature if needed. DO NOT subs-
tute parts.
 DO NOT alter the enclosure. Repairs should be done by Abram's Naon or distributors.
 DO NOT climb on top of the enclosure.
 In order to reduce the risk of pping, use provided stability straps to secure the enclose and
frame to the underlying standard wooden or metal bed frame (not included).
 Non-re retardant pillows, blankets, and stued animal are NOT recommended for this
product as they reduce the ame protecon it provides.
 Ensure your in-home maress (not provided) meets safety guidelines
(hps://sleepproducts.org/advocacy/federal-maress-regulaons/)
ENTRAPMENT AND SUFFOCATION HAZARD
Coverlet must be used at ALL mes to reduce the risk of serious injury or death from entrap-
ment or suocaon between the maress and bed enclosure.
WARNINGS

4
TECHNICAL SPECIFICATIONS
Operang Condions: The Safety Sleeper® is designed for normal indoor condions.
Storage Condions: The Safety Sleeper® should be stored in the provided suitcase
(30x18x12”) in ambient warehouse temperatures (15° to 25°C, or 59° to 77°F) at normal hu-
midity levels. Avoid excess moisture or high humidity that may damage product materials.
Size Height Length Width
Full 42” (107cm) 75” (190.5cm) 55” (140cm)
Queen 45” (114cm) 80” (203cm) 61.5” (156cm)
EU Double 107cm 200cm 144cm
AU/UK Double 107cm 191cm 141cm
Size Height Length Width
Full 8-10” 75” (190.5cm) 54” (137cm)
Queen 10-12” 80” (203cm) 60” (152.2cm)
EU Double 19-22cm 200cm 140cm
AU/UK Double 22-27cm 188-191cm 137-138cm
Enclosure & Frame Dimensions
Weight
Total weight including suitcase & air maress:
Full/Doubles: 42 lbs (19 kg)
Queen: 48 lbs (21.75 kg)
Maximum weight/load: 300 lbs (136 kg)
Maress Dimensions