AcceleVision LCDRV700 User manual
Digital LCD Color Monitor
Operating Instructions
Please read this manual thoroughly before operating the unit,
and keep it for future reference.
V1.0
LCDRV700
14
Symptom Possible Causes/Solutions
No picture, no sound
No picture
No sound
Dark picture
No color
Upside down or lateral
inverted picture
No reversing function
(i.e. Picture)
Improper connection of automobile adapter. Use of un-
authorized power supply. Power switch is on OFF position.
Check whether AV cable is properly connected.
Check whether audio wire is properly connected or the sound
volume is turned off or set too low.
Check whether brightness and contrast are adjusted correctly;
Check whether the environments temperature is too low.
Adjust the color settings.
The black wire of the monitor AV cable to the reversing light may
be loose. The red wire from the monitor may be loose.
9. Troubleshooting
Use the remote control horizontal /vertical selection switch to set
proper orientation
1. Precautions
2. Features
4. Accessories
5. Parts Identification
6. Remote Control Operation
7. Basic Operation
8. Menu
(1) Picture
(2) Option
(3) System
9. Troubleshooting
Contents
14
3. Technical Specifications
13
12
10
8
6
5
10
…………………………………………………………
…………………………………………………………
…………………………………………………………
………………………………………………………
………………………………………………………
………………………………………
………………………………………………
………………………………………………………
……………………………………………
……………………………………………………
…………………………………………………………
……………………………………………………
4
3
3
1
The sympoms described below do not necessarily mean a failure within the
display.Please check the following items before you initiate request for repair.
(4) Auto Scan 14
…………………………………………………………
(4) Auto Scan
CAM1 , CAM2, CAM3, AV options display on the screen as illustrated below :AUTO SCAN, SCAN TIME,
Press CH- to select .SCAN TIME
AUTO SCAN
CAM1
CAM2
CAM3
OFF
OFF
OFF
Press / to select 1S~90S.
AUTO SCAN
SCAN TIME
ON
5S
AV OFF
1. Precautions
Storage and Keeping
1. Do not expose the monitor to excessive heat or cold. The storage temperature of this device
is -30~+80℃, and the operating temperature is -20~+70 ℃. The humidity is Rh90%.
2. Never use this device near a bathtub, wash basin, kitchen, damp basement, swimming pool or
similar places.
3. Never use this device in environments with excessive moisture, dust or smoke.
4. Avoid dropping or striking this device.
5. Avoid using this device in enclosed spaces, areas with excessive vibration or subject to
severe impacts.
6. Never puncture, scratch or use abrasive cleaning materials on this device..
7. Do not place cables where they may be pinched or stepped on.
8. Leave at least a 2" space between the monitor and walls, cabinets or other objects to allow
adequate air circulation around the unit.
9. The monitor is not designed to be waterproof.
12 1
Operating Precautions
1. The device may be powered by a 12 or 24 volt automotive battery or vehicle electrical system
2. Observe polarity.
power s do not
Make sure all cables are connected properly. Improper cable connections may
damage the monitor. Remove the cable connection when you intend to use the unit.
1. High voltage is present within the monitor. The opening of the case should be by professionals.
2. Do not watch the video while driving unless you are monitoring the rear view camera display.
Warning!
!
Occasionally, a few highlights or dark spots may occur on the LCD screen. This is a very common
phenomenon in active matrix display technology, and doesn’t necessarily indicate any defects or faults.
Never try to repair this device by yourself. In case of any problems, please turn off the display at once and
notify our company or authorized dealer. The monitor is a complex device. Any disassembly or modification
may lead to damage and void the warrantee.
!
Special Notice
OPTION
SCALE
CAM1
CAM2
CAM3
AV
ON
NORMAL
NORMAL
NORMAL
NORMAL
LANG ENGLISH
Press / to select NORMAL / MIRROR.
Press CH- to select CAM1.
OPTION
SCALE
CAM1
CAM2
CAM3
AV
ON
NORMAL
NORMAL
NORMAL
NORMAL
LANG ENGLISH
Press / to select ON / OFF. Scale refers to the reversing distance indicator displayed
on the monitor.
Press CH- to select SCALE.
LANG , SCALE , CAM1 , CAM2, CAM3 , AV options display on the screen as illustrated below :
Press CH- to select LANG.
OPTION
SCALE
CAM1
CAM2
CAM3
AV
ON
NORMAL
NORMAL
NORMAL
NORMAL
LANG ENGLISH
Press / to select ENGLISH / FRENCH / PORTUGUESE / SPANISH /
RUSSIAN / GERMAN / ITALIAN / DUTCH.
(2) OPTION
2
1. Remove all the cable connections from the monitor before cleaning the unit.
2. Use a mild household detergent and clean the unit with a slightly damp,soft cloth.
Never use strong solvents such as thinner or benzine, as they might damage the finish
of the device.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of uninsulated "dangerous
voltage" within the product's enclosure that may be of sufficient magnitude to
constitute risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the appliance.
You are cautioned that any changes or modifications not expressly approved in this manual could
void your warrantee and neccessitate expensive repairs.
CAUTION
This symbol is intended to alert the user not to waste electrical and electronic
equipment.
Declaration of conformity
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any received, including
Interference
nterference that may cause undesired operation.i
e24
Maintenance
11
When in dark condition, and turn on the Auto Dim function,
display on the screen will be:
PICTURE
DIM BRIGHT
DIM CONTRAST
DIM COLOR
VOLUME
AUTO DIM
SCALE ADJUST
40
45
40
50
ON
↑↓
When turn off the Auto Dim function, this menu will not display.
Press CH- to select SCALE ADJUST.
PICTURE
BRIGHT
CONTRAST
COLOR
VOLUME
AUTO DIM
SCALE ADJUST
40
45
40
50
OFF
↑↓
Press / to select ↑↓ or .
The scale can be adjusted when it is displaying.
←
→
When exit menu and press , display on the screen will be:CH-
If SCALE ADJUST in ↑↓ state, the scale can be adjusted for up and down when
you press / , else the scale can be adjusted for left and right when
you press / .
10
2. Product Features
1. 7" TFT- LCD Color monitor with digital panel.
2. Audio output: 1W.
3. Loudspeaker: one 15x24mm round loudspeaker.
4. Power supply: Automobile storage battery (10-32V).
5. Power consumption: about 6W .
6. Outer dimension: 182mm (W) × 122mm (H) × 26mm (T) (without flush mount),
198mm (W) × 138mm (H) × 31mm (T) (with flush mount).
7. Dot pitch: 0.0642(W) x 0.1790(H)mm
8. Resolution: 800×3 (RGB) × 480.
9. Contrast: 500:1.
2
10. Brightness: 400cd/m.
11. Viewing angle: U: 50° / D: 70°, R/L: 70°/ 70°.
12. Operating temperature: -20~+70ºC,RH90%.
13. Storage temperature: -30~+80ºC, R 90%.
3. Technical Specifications
1. TFT LCD monitor with wide angle view and high resolution display.
2. Picture image may be adjusted for Horizontal, Vertical, Mirror and Normal viewing.
3. Select from 8 languages for user operation.
4. Automatic backlighting for buttons and automatic brightness control.
10. Automatic scanning function.
5. Full-function remote control.
6. Multiple video formats available: PAL / AUTO / NTSC.
7. Up to 3 AV inputs. Three cameras input on the rear and one A/V input on the front panel.
8. Operates from DC / 10 - 32V. Supports 12V or 24V automobile battery.
9. Automatically switches to back-up, left or right side camera views.
11. On-board speaker.
3
!
Special Notice
All specifications are subject to change without notice.
8. Menu
Press MENU to display the following options and settings:
1. PICTURE
2. OPTION
3. SYSTEM
(1) Picture
BRIGHT,CONTRAST, COLOR, VOLUME, AUTO DIM and SCALE ADJUST options
will display on the screen as illustrated below:
Press CH- to select BRIGHT.
PICTURE
BRIGHT
CONTRAST
COLOR
VOLUME
50
50
50
50
Press / to adjust the brightness level.
7.4.3. When the brown wire is connected to the positive wire of back-up light,
the monitor automatically switches to 3 (back-up camera) whenCAM
the back-up light is turned on. The distancing grid will also be displayed.
12. The scale can be adjusted for left, right up and down.
4. AUTO SCAN
AUTO DIM
SCALE ADJUST
OFF
↑↓
4. Accessories
Accessory supply may be different for different application.
!
Special Notice
49
Blue
ro nB w
White
Black 4
pin ma
le
Bkin
lac
4 p male
kin
Blac 4
p male
Black
Red
Black 13 pin female
Black 13 pin male
Digital Color LCD screen
Flush mount
Detaching piece
Insert the detaching piece as indicated by the white
arrow. Press in and lift up, the monitor will be released
from the flush mount.
7.3. Removing the Monitor:
7.3.1.
7.3.2.
Remove the monitor.
U- Support Bracket Center Mount Bracket
adapter cable IR Remote control
Flush Mount(optional)
Detaching Piece
Front Panel AV Input adapter
Black 4 pin male for Camera 1 / Camera 2 / Camera 3.
Single red wire to positive power supply of DC / 10-32V.
Single black wire to GND.
Single brown wire to positive power wire of back-up light .
Single white wire to positive power wire of left turn light .
Single blue wire to positive power wire of right turn light .
7.4.2. When the blue wire is connected to the positive wire of the right turn
light, the monitor automatically switches to 2 (right sideCAM
camera) when the right turn indicator is activated.
7.4.1. When the white wire is connected to the positive wire of the left turn
light , the monitor automatically switches to CAM1 (left side
camera) when the left turn indicator is activated.
Angle Adjustment screws7.4.Reversing Display:
CAM1
CAM2
Sun Shield
AV and Power supply
7.1. Connection of AV Input Cable
Align the small end of AV conversion adapter with the
AV jack on the front panel of the display. Then plug
in. Connect the RCA connectors to the output signal of
the video and/or audio of the DVD/ VCD player.
8
7. Basic Operation
7.2. Connection of AV Adapter and Controller Cable
5
Audio/ Video Input
Brightness increase Brightness decrease Channel selection - AV1/AV2/AV3/AV Selector
Menu
Remote control
sensor
Light level sensor
Power switch
Power indicator
Digital Color
5. Parts Identification
Hold the cable , align the side of jack
marked with on the female 13-pin
connector with the male 13-pin connector
marked with then firmly plug together.
Black 4 pin male for Camera1.
Black 4 pin male for Camera 2.
Black 4 pin male for Camera 3.
Single red wire to power wire of DC / 10-32V.
Single black wire to GND.
Single brown wire to positive power wire of the
back-up light.
Single white wire to positive power wire of left Light .
Single blue wire to positive power wire of right light .
1
2
3
4
5
6
7
8
Loudspeaker
Mounting bracket installation
LCD screen
6
6. Remote Control Operation
Power Switch
Menu
Call
Timer
Select AV1/AV2/AV3/AV
PAL / AUTO / NTSC
Vertical Flip
Channel Selection Up
Less Brightness
Picture Mode
Language Selection
Horizontal Flip
1. Please align the remote control with the infrared-receiving window on the monitor to operate.
2. Never disassemble the remote control or allow it to drop, or become wet.
3. Press the control buttons firmly. Allow 2 seconds for the picture to change.
!
Notice
Channel Selection Down
More Brightness
7
MUTE (Mute):
Press to select ENABLE/MUTE sound.
CH+ (Channel Selection+):
Press to select channel/item on menu.
Press to turn picture horizontally.
(Horizontal Turning of Picture):
MENU :
Press to show menu.
CH- (Channel Selection-):
Press to select channel/item on menu.
CALL (Call):
Press to close menu.
MODE (Picture Mode):
Press to select different picture modes (PERSONAL / STANDARD / SOFT / VIVID / LIGHT).
POWER (Power Switch):
Press to turn on/off the monitor.
Press to turn picture vertically.
(Vertical Turning of Picture):
TIMER:
Press to set the timer to shut down the monitor (10,20,30,40 and max 90 minutes).
SEL:
Press to select AV channels.
LANG(Language Selection):
Press to select language display of ENGLISH , FRENCH, PORTUGUESE,
SPANISH , RUSSIAN , GERMAN , ITALIAN or DUTCH options .
Press to decrease Brightness.
Press to increase Brightness.
SYS:
Press to select PAL / AUTO / NTSC.
Mute
6
6. Remote Control Operation
Power Switch
Menu
Call
Timer
Select AV1/AV2/AV3/AV
PAL / AUTO / NTSC
Vertical Flip
Channel Selection Up
Less Brightness
Picture Mode
Language Selection
Horizontal Flip
1. Please align the remote control with the infrared-receiving window on the monitor to operate.
2. Never disassemble the remote control or allow it to drop, or become wet.
3. Press the control buttons firmly. Allow 2 seconds for the picture to change.
!
Notice
Channel Selection Down
More Brightness
7
MUTE (Mute):
Press to select ENABLE/MUTE sound.
CH+ (Channel Selection+):
Press to select channel/item on menu.
Press to turn picture horizontally.
(Horizontal Turning of Picture):
MENU :
Press to show menu.
CH- (Channel Selection-):
Press to select channel/item on menu.
CALL (Call):
Press to close menu.
MODE (Picture Mode):
Press to select different picture modes (PERSONAL / STANDARD / SOFT / VIVID / LIGHT).
POWER (Power Switch):
Press to turn on/off the monitor.
Press to turn picture vertically.
(Vertical Turning of Picture):
TIMER:
Press to set the timer to shut down the monitor (10,20,30,40 and max 90 minutes).
SEL:
Press to select AV channels.
LANG(Language Selection):
Press to select language display of ENGLISH , FRENCH, PORTUGUESE,
SPANISH , RUSSIAN , GERMAN , ITALIAN or DUTCH options .
Press to decrease Brightness.
Press to increase Brightness.
SYS:
Press to select PAL / AUTO / NTSC.
Mute
7.1. Connection of AV Input Cable
Align the small end of AV conversion adapter with the
AV jack on the front panel of the display. Then plug
in. Connect the RCA connectors to the output signal of
the video and/or audio of the DVD/ VCD player.
8
7. Basic Operation
7.2. Connection of AV Adapter and Controller Cable
5
Audio/ Video Input
Brightness increase Brightness decrease Channel selection - AV1/AV2/AV3/AV Selector
Menu
Remote control
sensor
Light level sensor
Power switch
Power indicator
Digital Color
5. Parts Identification
Hold the cable , align the side of jack
marked with on the female 13-pin
connector with the male 13-pin connector
marked with then firmly plug together.
Black 4 pin male for Camera1.
Black 4 pin male for Camera 2.
Black 4 pin male for Camera 3.
Single red wire to power wire of DC / 10-32V.
Single black wire to GND.
Single brown wire to positive power wire of the
back-up light.
Single white wire to positive power wire of left Light .
Single blue wire to positive power wire of right light .
1
2
3
4
5
6
7
8
Loudspeaker
Mounting bracket installation
LCD screen
4. Accessories
Accessory supply may be different for different application.
!
Special Notice
49
Blue
ro nB w
White
Black 4
pin ma
le
Bkin
lac
4 p male
kin
Blac 4
p male
Black
Red
Black 13 pin female
Black 13 pin male
Digital Color LCD screen
Flush mount
Detaching piece
Insert the detaching piece as indicated by the white
arrow. Press in and lift up, the monitor will be released
from the flush mount.
7.3. Removing the Monitor:
7.3.1.
7.3.2.
Remove the monitor.
U- Support Bracket Center Mount Bracket
adapter cable IR Remote control
Flush Mount(optional)
Detaching Piece
Front Panel AV Input adapter
Black 4 pin male for Camera 1 / Camera 2 / Camera 3.
Single red wire to positive power supply of DC / 10-32V.
Single black wire to GND.
Single brown wire to positive power wire of back-up light .
Single white wire to positive power wire of left turn light .
Single blue wire to positive power wire of right turn light .
7.4.2. When the blue wire is connected to the positive wire of the right turn
light, the monitor automatically switches to 2 (right sideCAM
camera) when the right turn indicator is activated.
7.4.1. When the white wire is connected to the positive wire of the left turn
light , the monitor automatically switches to CAM1 (left side
camera) when the left turn indicator is activated.
Angle Adjustment screws7.4.Reversing Display:
CAM1
CAM2
Sun Shield
AV and Power supply
10
2. Product Features
1. 7" TFT- LCD Color monitor with digital panel.
2. Audio output: 1W.
3. Loudspeaker: one 15x24mm round loudspeaker.
4. Power supply: Automobile storage battery (10-32V).
5. Power consumption: about 6W .
6. Outer dimension: 182mm (W) × 122mm (H) × 26mm (T) (without flush mount),
198mm (W) × 138mm (H) × 31mm (T) (with flush mount).
7. Dot pitch: 0.0642(W) x 0.1790(H)mm
8. Resolution: 800×3 (RGB) × 480.
9. Contrast: 500:1.
2
10. Brightness: 400cd/m.
11. Viewing angle: U: 50° / D: 70°, R/L: 70°/ 70°.
12. Operating temperature: -20~+70ºC,RH90%.
13. Storage temperature: -30~+80ºC, R 90%.
3. Technical Specifications
1. TFT LCD monitor with wide angle view and high resolution display.
2. Picture image may be adjusted for Horizontal, Vertical, Mirror and Normal viewing.
3. Select from 8 languages for user operation.
4. Automatic backlighting for buttons and automatic brightness control.
10. Automatic scanning function.
5. Full-function remote control.
6. Multiple video formats available: PAL / AUTO / NTSC.
7. Up to 3 AV inputs. Three cameras input on the rear and one A/V input on the front panel.
8. Operates from DC / 10 - 32V. Supports 12V or 24V automobile battery.
9. Automatically switches to back-up, left or right side camera views.
11. On-board speaker.
3
!
Special Notice
All specifications are subject to change without notice.
8. Menu
Press MENU to display the following options and settings:
1. PICTURE
2. OPTION
3. SYSTEM
(1) Picture
BRIGHT,CONTRAST, COLOR, VOLUME, AUTO DIM and SCALE ADJUST options
will display on the screen as illustrated below:
Press CH- to select BRIGHT.
PICTURE
BRIGHT
CONTRAST
COLOR
VOLUME
50
50
50
50
Press / to adjust the brightness level.
7.4.3. When the brown wire is connected to the positive wire of back-up light,
the monitor automatically switches to 3 (back-up camera) whenCAM
the back-up light is turned on. The distancing grid will also be displayed.
12. The scale can be adjusted for left, right up and down.
4. AUTO SCAN
AUTO DIM
SCALE ADJUST
OFF
↑↓
2
1. Remove all the cable connections from the monitor before cleaning the unit.
2. Use a mild household detergent and clean the unit with a slightly damp,soft cloth.
Never use strong solvents such as thinner or benzine, as they might damage the finish
of the device.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of uninsulated "dangerous
voltage" within the product's enclosure that may be of sufficient magnitude to
constitute risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the appliance.
You are cautioned that any changes or modifications not expressly approved in this manual could
void your warrantee and neccessitate expensive repairs.
CAUTION
This symbol is intended to alert the user not to waste electrical and electronic
equipment.
Declaration of conformity
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any received, including
Interference
nterference that may cause undesired operation.i
e24
Maintenance
11
When in dark condition, and turn on the Auto Dim function,
display on the screen will be:
PICTURE
DIM BRIGHT
DIM CONTRAST
DIM COLOR
VOLUME
AUTO DIM
SCALE ADJUST
40
45
40
50
ON
↑↓
When turn off the Auto Dim function, this menu will not display.
Press CH- to select SCALE ADJUST.
PICTURE
BRIGHT
CONTRAST
COLOR
VOLUME
AUTO DIM
SCALE ADJUST
40
45
40
50
OFF
↑↓
Press / to select ↑↓ or .
The scale can be adjusted when it is displaying.
←
→
When exit menu and press , display on the screen will be:CH-
If SCALE ADJUST in ↑↓ state, the scale can be adjusted for up and down when
you press / , else the scale can be adjusted for left and right when
you press / .
1. Precautions
Storage and Keeping
1. Do not expose the monitor to excessive heat or cold. The storage temperature of this device
is -30~+80℃, and the operating temperature is -20~+70 ℃. The humidity is Rh90%.
2. Never use this device near a bathtub, wash basin, kitchen, damp basement, swimming pool or
similar places.
3. Never use this device in environments with excessive moisture, dust or smoke.
4. Avoid dropping or striking this device.
5. Avoid using this device in enclosed spaces, areas with excessive vibration or subject to
severe impacts.
6. Never puncture, scratch or use abrasive cleaning materials on this device..
7. Do not place cables where they may be pinched or stepped on.
8. Leave at least a 2" space between the monitor and walls, cabinets or other objects to allow
adequate air circulation around the unit.
9. The monitor is not designed to be waterproof.
12 1
Operating Precautions
1. The device may be powered by a 12 or 24 volt automotive battery or vehicle electrical system
2. Observe polarity.
power s do not
Make sure all cables are connected properly. Improper cable connections may
damage the monitor. Remove the cable connection when you intend to use the unit.
1. High voltage is present within the monitor. The opening of the case should be by professionals.
2. Do not watch the video while driving unless you are monitoring the rear view camera display.
Warning!
!
Occasionally, a few highlights or dark spots may occur on the LCD screen. This is a very common
phenomenon in active matrix display technology, and doesn’t necessarily indicate any defects or faults.
Never try to repair this device by yourself. In case of any problems, please turn off the display at once and
notify our company or authorized dealer. The monitor is a complex device. Any disassembly or modification
may lead to damage and void the warrantee.
!
Special Notice
OPTION
SCALE
CAM1
CAM2
CAM3
AV
ON
NORMAL
NORMAL
NORMAL
NORMAL
LANG ENGLISH
Press / to select NORMAL / MIRROR.
Press CH- to select CAM1.
OPTION
SCALE
CAM1
CAM2
CAM3
AV
ON
NORMAL
NORMAL
NORMAL
NORMAL
LANG ENGLISH
Press / to select ON / OFF. Scale refers to the reversing distance indicator displayed
on the monitor.
Press CH- to select SCALE.
LANG , SCALE , CAM1 , CAM2, CAM3 , AV options display on the screen as illustrated below :
Press CH- to select LANG.
OPTION
SCALE
CAM1
CAM2
CAM3
AV
ON
NORMAL
NORMAL
NORMAL
NORMAL
LANG ENGLISH
Press / to select ENGLISH / FRENCH / PORTUGUESE / SPANISH /
RUSSIAN / GERMAN / ITALIAN / DUTCH.
(2) OPTION
13
Press / to select 16:9 or 4:3.
Press CH- to select ZOOM.
SYSTEM
BLUE BACK
HORIZONTAL
VERTICAL
ZOOM
COLOR -SYS PAL
ON
16:9
Press CH- to select BLUE BACK.
SYSTEM
BLUE BACK
HORIZONTAL
VERTICAL
ZOOM
COLOR -SYS AUTO
ON
16:9
Press / to select ON / OFF.
(3) System
COLOR-SYS, BLUE BACK, HORIZONTAL, VERTICAL, ZOOM functions
will display on the screen as illustrated below :
Press CH- to select COLOR-SYS .
Press / to select PAL / AUTO / NTSC.
SYSTEM
COLOR -SYS
BLUE BACK
HORIZONTAL
VERTICAL
ZOOM
SYSTEM
BLUE BACK
HORIZONTAL
VERTICAL
ZOOM
COLOR -SYS AUTO
ON
16:9
14
Symptom Possible Causes/Solutions
No picture, no sound
No picture
No sound
Dark picture
No color
Upside down or lateral
inverted picture
No reversing function
(i.e. Picture)
Improper connection of automobile adapter. Use of un-
authorized power supply. Power switch is on OFF position.
Check whether AV cable is properly connected.
Check whether audio wire is properly connected or the sound
volume is turned off or set too low.
Check whether brightness and contrast are adjusted correctly;
Check whether the environments temperature is too low.
Adjust the color settings.
The black wire of the monitor AV cable to the reversing light may
be loose. The red wire from the monitor may be loose.
9. Troubleshooting
Use the remote control horizontal /vertical selection switch to set
proper orientation
1. Precautions
2. Features
4. Accessories
5. Parts Identification
6. Remote Control Operation
7. Basic Operation
8. Menu
(1) Picture
(2) Option
(3) System
9. Troubleshooting
Contents
14
3. Technical Specifications
13
12
10
8
6
5
10
…………………………………………………………
…………………………………………………………
…………………………………………………………
………………………………………………………
………………………………………………………
………………………………………
………………………………………………
………………………………………………………
……………………………………………
……………………………………………………
…………………………………………………………
……………………………………………………
4
3
3
1
The sympoms described below do not necessarily mean a failure within the
display.Please check the following items before you initiate request for repair.
(4) Auto Scan 14
…………………………………………………………
(4) Auto Scan
CAM1 , CAM2, CAM3, AV options display on the screen as illustrated below :AUTO SCAN, SCAN TIME,
Press CH- to select .SCAN TIME
AUTO SCAN
CAM1
CAM2
CAM3
OFF
OFF
OFF
Press / to select 1S~90S.
AUTO SCAN
SCAN TIME
ON
5S
AV OFF
Table of contents
