ACL VOLANSYS CENTAURI-200 User manual

User Guide (UG)
CENTAURI-200
Revision: 3.0
Date: 02-06-2022
Volansys Technologies Private Limited
Block A 7th Floor, Safal Profitaire, Corporate Road,
Prahladnagar, Ahmedabad 380015, India
www.volansys.com
Phone: [phone]
Email: [e-mail]
Confidentiality Notice
Copyright © 2020Volansys – All rights reserved.
This document is authored by Volansys and is Volansys’ intellectual property, including the copyrights in all countries in the world. This
document is provided under a license to use only with all other rights, including ownership rights, being retained by Volansys. This file may not
be distributed, copied, or reproduced in any manner, electronic or otherwise, without the express written consent of Volansys.

CENTAURI-200 User Guide
VT-ENG-TMP-UG | Rev 1.1 | 31-Jul-19 Volansys-Confidential Page 2of 31
TABLE OF CONTENTS
1 INTRODUCTION ..................................................................................................................................................... 5
1.1 PURPOSE ................................................................................................................................................................. 5
1.2 SCOPE ..................................................................................................................................................................... 5
1.2.1 PREREQUISITES ...................................................................................................................................................... 5
1.2.2 SUPPORTED SOFTWARE AND HARDWARE PLATFORMS ..................................................................................................5
1.3 ACRONYMS & ABBREVIATIONS .................................................................................................................................... 5
1.4 REFERENCES .............................................................................................................................................................6
1.5 DOCUMENT CONVENTIONS .........................................................................................................................................6
1 SYSTEM OVERVIEW ............................................................................................................................................... 7
2 SETUP PREREQUISITES .......................................................................................................................................... 8
2.1 HARDWARE REQUIREMENTS ....................................................................................................................................... 8
2.2 HARDWARE OPTIONAL REQUIREMENTS ........................................................................................................................ 8
3 MOBILE APPLICATION SETUP ................................................................................................................................ 9
3.1 INSTALLATION (ANDROID MOBILE APPLICATION) ............................................................................................................9
3.2 INSTALLATION (IOS MOBILE APPLICATION) ................................................................................................................... 9
3.3 INITIAL SETUP AND USER REGISTRATION ......................................................................................................................10
4 GATEWAY SETUP .................................................................................................................................................13
4.1 GATEWAY LED INDICATION ...................................................................................................................................... 13
4.2 GATEWAY SWITCH FUNCTION ....................................................................................................................................13
4.3 GATEWAY INITIAL SETUP .......................................................................................................................................... 14
4.3.1 Gateway Setup with Wi-Fi .......................................................................................................................... 14
4.3.2 Gateway Setup with Ethernet cable ........................................................................................................... 14
4.4 GATEWAY COMMISSIONING [REGISTRATION] ...............................................................................................................15
4.4.1 Gateway Registration ................................................................................................................................. 15
4.4.2 Factory reset the gateway .......................................................................................................................... 19
4.5 CHANGE GATEWAY NETWORK INTERFACE FOR IP CONNECTIVITY (WI-FI OR ETHERNET) ..................................................... 21
4.5.1 Change from Wi-Fi to Ethernet ...................................................................................................................21
4.5.2 Change from Ethernet to Wi-Fi ...................................................................................................................21
4.6 REMOVE GATEWAY ................................................................................................................................................. 22
5 END DEVICE SETUP AND CONTROL ......................................................................................................................23
5.1 Z-WAVE OR ZIGBEE MODULES ...................................................................................................................................23
5.2 Z-WAVE/ ZIGBEE END DEVICE COMMISSIONING .......................................................................................................... 23
5.3 END DEVICE PROPERTIES ..........................................................................................................................................26
5.4 Z-WAVE / ZIGBEE END DEVICE CONTROLLING AND MONITORING. ...................................................................................27
5.4.1 Z-Wave / ZigBee bulb control ..................................................................................................................... 27
5.4.2 Z-Wave / ZigBee device monitoring ............................................................................................................28
5.5 REMOVE Z-WAVE END DEVICE ................................................................................................................................. 29

CENTAURI-200 User Guide
VT-ENG-TMP-UG | Rev 1.1 | 31-Jul-19 Volansys-Confidential Page 3of 31
5.6 REMOVE ZIGBEE END DEVICE ................................................................................................................................... 30
LISTS OF TABLES
TABLE 1 GATEWAY LED INDICATION ....................................................................................................................................13
TABLE 2 GATEWAY SWITCH FUNCTION ................................................................................................................................. 14
LISTS OF FIGURES
FIGURE 1- 1 GATEWAY SETUP ARCHITECTURE .......................................................................................................................... 7
FIGURE 3- 1 MOBILE APPLICATION LAUNCH PAGE ................................................................................................................. 10
FIGURE 3- 2 USER REGISTRATION FOR GATEWAY ................................................................................................................... 11
FIGURE 3- 3 HOME SCREEN AFTER SUCCESSFUL LOGIN ............................................................................................................12
FIGURE 4- 1 CENTAURI-200 GATEWAY ............................................................................................................................. 15
FIGURE 4- 2 IOTIFY – ADD GATEWAY .................................................................................................................................. 16
FIGURE 4- 3 GATEWAY PROVISIONING ................................................................................................................................. 17
FIGURE 4- 4 GATEWAY LIST ................................................................................................................................................18
FIGURE 4- 5 GATEWAY PROPERTY CHANGE ........................................................................................................................... 19
FIGURE 4- 6 GATEWAY WI-FI RESET BUTTON ........................................................................................................................ 20
FIGURE 4- 7 REMOVE GATEWAY ......................................................................................................................................... 22
FIGURE 5- 1 MIKROBUS BASED Z-WAVE 700 MODULE ...........................................................................................................23
FIGURE 5- 2 MIKROBUS BASED ZIGBEE JN5179 MODULE ....................................................................................................... 23
FIGURE 5- 3 END DEVICE LISTING SCREEN WITH NO END-DEVICE PAIRED .....................................................................................25
FIGURE 5- 4 COMMISSIONED GATEWAY ............................................................................................................................... 25
FIGURE 5- 5 WAITING FOR END-DEVICE PAIRING ....................................................................................................................25
FIGURE 5- 6 SUCCESSFUL END-DEVICE LISTING ...................................................................................................................... 26
FIGURE 5- 7 END DEVICE INFORMATION ............................................................................................................................... 26
FIGURE 5- 8 ZIGBEE / Z-WAVE BULB CONTROL FROM MOBILE APPLICATION ................................................................................27
FIGURE 5- 9 ZIGBEE / Z-WAVE DOOR SENSOR MONITORING FROM MOBILE APPLICATION ..............................................................28
FIGURE 5- 10 Z-WAVE MULTI SENSOR MONITORING FROM MOBILE APPLICATION ........................................................................29
FIGURE 5- 11 Z-WAVE REMOVE END-DEVICE FROM MOBILE APPLICATION .................................................................................. 30
FIGURE 5- 12 ZIGBEE REMOVE END-DEVICE FROM MOBILE APPLICATION ....................................................................................31

CENTAURI-200 User Guide
VT-ENG-TMP-UG | Rev 1.1 | 31-Jul-19 Volansys-Confidential Page 4of 31
Revision History
Date
Version
Details of change
Author
Reviewers
Approvers
10-08-2019
Draft 0.1
Initial Draft
MK
KB, RT
KB
29-08-2019
1.0
First Release
MK
RT, NP
KB
12-12-2019
1.1
Added Zigbee device control in
section 5.
Updated IoTiFy link in Section 3
NP
KB
KB
06-02-2020
1.2
Updated section 4.3 and updated
the document for Zigbee support.
NP
KB
KB
04-03-2020
1.3
Corrected LED2 indication in
chapter 4.
NP
KB
KB
13-03-2020
1.4
Updeted device provisioning section
NP
KB
KB
06-08-2020
1.5
Updated Switch indication in
Chapter 4
NP
KB
KB
19-10-2021
1.6
Added screenshots for complete
gateway registration process in
Section 4.4.1 and updated latest Z-
wave mikrobus module design
picture in Section 5.1.
NP
KB
KB
20-10-2021
2.0
Baselined the document
NP
KB
KB
02-06-2022
3.0
Updated the logo in the document
YP
NP
NP

CENTAURI-200 User Guide
VT-ENG-TMP-UG | Rev 1.1 | 31-Jul-19 Volansys-Confidential Page 5of 31
1 INTRODUCTION
This document will guide an end user in getting started with the CENTAURI-200.
1.1 Purpose
This document will address the following things:
1. Getting Started with CENTAURI-200 demonstration
2. System Overview
3. CENTAURI-200 Gateway Setup
4. End device setup and control
1.2 Scope
The scope of the guide is to describe the various functionalities to configure CENTAURI-200 using
mobile application for the user. It also demonstrates the setup and control of Z-wave and Zigbee
end devices. This document does not include the flashing steps of the CENTAURI-200 gateway.
1.2.1 Prerequisites
In this guide, it is assumed that CENTAURI-200 is available with the user and flashed with the
latest CENTAURI-200 release, links for software release, mobile application and necessary
accounts to set up the Cloud application.
1.2.2 Supported Software and Hardware Platforms
CENTAURI-200 functionality is tested with the following combination of operating system,
hardware platform, software versions, phone model or iOS/Android versions. CENTAURI -200
application may work with other versions of operating system, hardware, software, phone model
or iOS/Android version. The functionality of the CENTAURI-200 will not be guaranteed by Volansys
on any other combinations other than the one mentioned below:
Operating System – Yocto flavored Linux OS
Hardware board version – 1.0
Software version – 1.0.0
iPhone/iOS version – 10.x and higher
Android version – Lollipop 5.0 and higher
1.3 Acronyms & Abbreviations
Terms
Definition
AP
Access point
GW
Gateway
ED
End Device

CENTAURI-200 User Guide
VT-ENG-TMP-UG | Rev 1.1 | 31-Jul-19 Volansys-Confidential Page 6of 31
EUI
Extended Unique Identifier
OTA
Over The Air
1.4 References
Reference Document Title
Provided by
Remarks
NA
1.5 Document Conventions
This element signifies a useful information or tip or suggestion
This element signifies a warning or proceed with caution
This element signifies that the action should be avoid

CENTAURI-200 User Guide
VT-ENG-TMP-UG | Rev 1.1 | 31-Jul-19 Volansys-Confidential Page 7of 31
1 SYSTEM OVERVIEW
CENTAURI-200 Gateway is a central device to run the out of the box demonstration. In this setup, the
user can control and monitor the Z-wave and ZigBee end devices with help of mobile application. To do
the setup, the user needs to provide Internet connectivity to CENTAURI-200 Gateway. The Gateway
supports Ethernet, WiFi and LTE to connect to the cloud. The user can add end devices in the system
using mobile application. Once the end devices are added to the system, the user can control them via
the mobile application.
Figure 1- 1 Gateway setup architecture

CENTAURI-200 User Guide
VT-ENG-TMP-UG | Rev 1.1 | 31-Jul-19 Volansys-Confidential Page 8of 31
2 SETUP PREREQUISITES
2.1 Hardware Requirements
User needs following listed items to fulfill setup requirement
CENTAURI-200 Gateway.
oZ-wave controller Module
oZigBee Controller Module
oInternet connectivity on Gateway via Ethernet or Wi-Fi.
2.2 Hardware Optional Requirements
The following Z-Wave / ZigBee end devices are supported
oZ-Wave bulb, door sensor, motion sensor, Multi sensor etc.
oZigBee bulb, door sensor, motion sensor, Water Leak Sensor, etc.

CENTAURI-200 User Guide
VT-ENG-TMP-UG | Rev 1.1 | 31-Jul-19 Volansys-Confidential Page 9of 31
3 MOBILE APPLICATION SETUP
3.1 Installation (Android Mobile Application)
1. The IoTify Android application is available on Google Play Store.
3.2 Installation (iOS Mobile Application)
1. The IoTify iOS application is available on the Apple Application store.

CENTAURI-200 User Guide
VT-ENG-TMP-UG | Rev 1.1 | 31-Jul-19 Volansys-Confidential Page 10 of 31
3.3 Initial setup and User registration
1. Launch/open installed application in the mobile. User can see below screen
Figure 3- 1 Mobile Application Launch Page
2. If prompted for any permission, please allow.
3. Follow user registration process for creating account. Enter verification code received on email
to complete registration process.