Adam A5X User manual

A5X Nearfield Monitor
Operation manual / Bedienungsanleitung
English / deutsch
A5X

2
Safety Instructions
Please read the following safety instructions before setting up your
system. Keep the instructions for subsequent reference. Please heed
the warnings and follow the instructions.
Caution: To reduce the risk of electric shock, do not open the loud-
speaker. There are no user-serviceable parts inside. Refer servicing to
qualified service personnel.
This product, as well as all attached extension cords, must be terminated
with an earth ground three-conductor AC mains power cord like the one
supplied with the product. To prevent shock hazard, all three components
must always be used.
Never replace any fuse with a value or type other than those specified.
Never bypass any fuse.
Always switch off your entire system before connecting or disconnecting
any cables, or when cleaning any components.
Do not place this unit on an ustable cart, stand or tripod, bracket or table.
The unit may fall, causing serious injury and/or serious damage. When cart
is used, use caution when moving the cart/apparatus combination.
Do not expose this product to rain or moisture, never wet the inside with
any liquid and never pour or spill liquids directly onto this unit. Please do
not ut any objects filled with liquids (e.g. vases, etc.) onto the speaker.
Check if the specified voltage matches the voltage of the power supply
you use. If this is not the case do not connect the loudspeakers to a power
source! Please contact your local dealer or national distributor.
Caution
Risk of electrical shock
Do not open
Risque de shock electrique
Ne pas ouvrier
CAUTION: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT REMOVE BACK COVER OR ANY OTHER PART.
NO USER-SERVICABLE PARTS INSIDE.
DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
REFER SERVICING TO QUALIFIED PERSONNEL.

3
English
Safety Instructions
Protect the cord from being walked on or pinched.
Always use fully checked cables. Defective cables can harm your speakers.
They are a common source for any kind of noise, hum, crackling etc.
Always keep electrical equipment out of the reach of children.
Always unplug sensitive electronic equipment during lightning storms.
The monitor should be installed near the socket outlet and disconnection of
the device should be easily accessible.
To completely disconnect from AC mains, disonnect the power supply from
the AC receptacle. Never use flammable or combustible chemicals for
cleaning audio components.
Avoid touching the speaker membranes and do not block the woofer’s
ventilation ports.
Never expose this product to extremely high or low temperatures. Never
operate this product in an explosive atmosphere.
High SPL’s may damage your hearing! Please do not get close to the
loudspeakers when using them at high volumes.
Please note that the diaphragms build up a magnetic field. Do not ply with
magnetic items at close range to the diaphragms.
Assure free airflow behind the speakers to maintain sufficient cooling.

4
Table of contents
Safety Instructions.........................2-3
1. Introduction ...................................5
2. Quick Start.....................................6
2.1 Important Information....................6
2.2 Quick Start A5X .............................6
3. Connecting the Speaker.................7
3.1 Basic Connections .........................7
3.2 The Stereo Link..............................7
4. Speaker Placement........................8-10
4.1 Vertical set up................................8
4.2 Horizontal set up............................8
4.3 Tweeter at height of ears ...............9
4.4 The stereo triangle.........................9
4.5 Surround placement ......................10
4.6 Stand/Wall mounting.....................10
5. Speaker Adjustments.....................11
5.1 Control panel .................................11
5.1 Tweeter level..................................11
5.1 Room EQs (Shelve filter) ................11
6. Trouble Shooting............................12
6.1 No or distorted signal ....................11
6.1 Parasitic noises..............................11
7. Maintenance ..................................13
8. Transportation / Package ..............13
9. Environmental Information.............13
10. EU Declaration of Conformity ........14
11. Limited Warranty............................15
11.1 Terms and Conditions ....................15
11.2 How to claim..................................15
12. Technical Data /Technische Daten 16

5
English
1. Introduction
Dear customer,
Thank you for choosing the ADAM Audio A5X Nearfield monitor!
ADAM loudspeakers are built for maximum quality reproduction and audio
perfection. With the A5X you have selected a precise, high-resolution speaker
system that allows you to both evaluate and enjoy audio recordings. This
monitor meets highest expectations in sound quality and craftsmanship.
This manual is intended to provide you with information about your new
ADAMs. It contains important information regarding safety, setting up,
handling, and warranty. We request that you read these sections carefully
to ensure easy set up and prevent potential problems.
The A5X is a compact near field monitor. It is perfectly suited for a wide
variety of stereo and multi-channel professional applications including small
control rooms, desktops, mobile facilities and post-production edit bays as
well as connection to your favorite mp3-players and gaming consoles…in
other words, in any situation where a combination of no-compromise sound
reproduction and a small footprint is required.
The A5X is a two-way ported active system that uses ADAM’s proprietary
X-ART folded ribbon tweeter ensuring full compatibility with the latest
expanded high frequency resolution media formats, and a conventional
bass/midrange driver below the crossover frequency of 2.5kHz. Each section
uses an individual amp with continuous output of up to 50 Watts (RMS).
If you have any questions about this or any of our products, please don’t
hesitate to contact us – we will be happy to assist you.
For detailed information concerning ADAM’s technologies and products,
complete reviews, and a list of worldwide ADAM users and studios, please
visit our website:
www.adam-audio.com
We hope very much that you really enjoy your new loudspeakers, and wish
you many delightful hours with them.
The ADAM Audio Team

6
2. Quick Start
Important Information for set up
After having unpacked your loudspeaker, please allow the system to acclimate
to the temperature of the room for approximately an hour.
It is important to ensure the speakers sit firmly on a solid surface!
We recommend that you retain the original packaging, as it is the best way to
guarantee safe transportation should the need to do so arise.
Please note that the loudspeakers will take some break-in time to achieve
optimum sonic performance.
Quick Start
Before connecting the loudspeakers to your audio components and the
power source make sure that both the loudspeakers and your audio system
are switched off and set the level controls fully counterclockwise.
There are two options of connection:
Basic active speaker use. Connect your sound source or mixing console to the
speakers. Use either the RCA (unbalanced) or the XLR (balanced) connectors.
You will find the connector wiring printed on the speaker’s rear panel (for
further information, see 3.1).
Stereo Link. If you want to use the Stereo Link (controlling the overall volume
by one control), please see 3.2.
Check if the specified voltage matches the voltage of the power supply you
use. If this is not the case do not connect the loudspeakers to a power source!
Please contact your local dealer or national distributor.
If the voltages match, use the included power cables to connect the
loudspeaker to the AC sockets.
Switch on the main on/off switches on the front panel of the loudspeakers.
Make sure that the line out level (volume) of your stereo is either at a low level
or all the way off. Then, switch on your audio system.
Turn on your source of music and adjust the volume carefully.
2.1
2.2
d)
a)
b)
c)
e)
f)

7
English
a)
a)
b)
b)
c)
3. Connecting the Speakers
Basic active speaker connection
For the basic active speaker connection,
please use mono XLR or RCA cables.
In most professional applications XLR
will be the best choice, while RCA is
more common in HiFi applications. Each
one of the two loudspeakers has to be
connected to one channel of the sound
source.
The Stereo Link
If you wish to use the Stereo Link that
allows adjustment of the volume of
both loudspeakers with a single master
control, please proceed as follows:
First, connect Speaker 1 (that is supposed
to control the overall volume) to your
preamplifier, sound source, etc., using a
stereo RCA (*1) cable.
Second, connect Speaker 2 to Speaker 1
via the Stereo Link output of Speaker 1
and the Analog Input of Speaker 2. Please
use the provided (or another) mono RCA
cable.
Please note:
On the front side of the unit functioning as master, a corresponding
white LED will illuminate as soon as mono RCA is connected to the
Stereo Link output.
Unlike the common ‘master-slave-configuration’, any A5X that is connected
accordingly can function as either a master or a slave unit.
For an equal volume level of both speakers please make sure that the volume
knob of speaker 2 is snapped in the middle position.
3.1
3.2
white
LED
fig. 2: Stereo Link
RCA (stereo)
Speaker 1 Speaker 2
mono RCA (*2)
TWEETER LEVEL
A5X
LOW SHELFHIGH SHELF
OUTPUT
STEREOLINK
INPUT
UNBALANCED IN
BALANCED IN
CONTROLS
IN-/ OUTPUTS
0
-6 dB +6 dB
0
-6 dB +6 dB
0
-4 dB +4 dB
Serial No.
T1.6AL (230V~,50Hz)
T3AL (115V~,60Hz)
130WATTS
TWEETER LEVEL
A5X
LOW SHELFHIGH SHELF
OUTPUT
STEREOLINK
INPUT
UNBALANCED IN
BALANCED IN
CONTROLS
IN-/ OUTPUTS
0
-6 dB +6 dB
0
-6 dB +6 dB
0
-4 dB +4 dB
Serial No.
T1.6AL (230V~,50Hz)
T3AL (115V~,60Hz)
130WATTS
fig. 1: Common connection
2 x RCA
or
2 x XLR
Speaker 1 Speaker 2
TWEETER LEVEL
A5X
LOW SHELFHIGH SHELF
OUTPUT
STEREOLINK
INPUT
UNBALANCED IN
BALANCED IN
CONTROLS
IN-/ OUTPUTS
0
-6 dB +6 dB
0
-6 dB +6 dB
0
-4 dB +4 dB
Serial No.
T1.6AL (230V~,50Hz)
T3AL (115V~,60Hz)
130WATTS
TWEETER LEVEL
A5X
LOW SHELFHIGH SHELF
OUTPUT
STEREOLINK
INPUT
UNBALANCED IN
BALANCED IN
CONTROLS
IN-/ OUTPUTS
0
-6 dB +6 dB
0
-6 dB +6 dB
0
-4 dB +4 dB
Serial No.
T1.6AL (230V~,50Hz)
T3AL (115V~,60Hz)
130WATTS

8
4. Speaker Placement
Please make sure that there are no obstacles in the way from the monitor to
your ears. You should be able to see the speakers completely.
Vertical set up
Hoizontal set up
If you choose to use your speakers in horizontal position as indicated below,
please make sure that the set up is mirrored/symmetrical, i.e. that the
tweeters both face either the outwards or inwards. This is crucial for a precise
stereo signal.
fig 4: horizontal / mirror symmetrical set up
4.1
so:
or so:
4.2
The A5X has been designed for a
vertical set up. The speakers must
be positioned on a solid surface or
a stand.
Please note that vibrating parts of
nearby objects can mask the sound.
fig 3: vertical set up
A3X
A3X
A3X
A3X
A3X
A3X

9
English
4. Speaker Placement
Tweeter at the height of ears
The Tweeter should be positioned approximately at the height of your ears. In
case you need to position the speaker in a significant lower or higher position,
the monitor should be angled accordingly.
fig 5: Tweeter at height of ears / speaker angling
The Stereo Triangle
If the loudspeaker is going to be used for stereo applications, the optimum
listening position should be at the top of an imaginary equilateral triangle
with the two loudspeakers should be placed at the other two points of this
triangle (see fig. 6).
The loudspeakers should be aligned with the listener’s position.
4.3
4.4
fig. 6: Stereo Triangle
• bothloudspeakerandthelisteningspotshould
form a equilateral triangle with approx. the
samedistancesbetweenloudspeakersandthe
loudspeakers/thelisteningspot
• alignmenttowardslisteningspot

10
4. Speaker Placement
Surround Placement
Speaker positioning for multi-channel stereo purposes is ideally based on
a circle with speakers placed at 0° (Center), 30° (Front Right), 110° (Rear
Right), 250° (Rear Left), 330° (Front Left), with the listener being the circle’s
center (Radius between 0.7-2.0 m). This ITU recommended configuration may
vary depending on the purpose of the control room (music or film). However,
it is recommended to create a symmetrical listening position with the front
side and surround speaker pointing to the listener’s ear.
The distance to the surrounding walls should be at least 40 cm to avoid early
reflections, which can degrade the sound.
fig 7: Surround set up
Stand/Wall Mounting
On the rear side, you will find two M8 (8 mm) metric strew threads for stand/
wall mounting. Further equipment (e.g. Omnimount) for mounting is also
available.
4.6
4.5

11
English
5.Speaker Adjustment
Controls
On the rear side you will find controls that
allows detailed fine-tuning of your loud-
speakers to your particular room acoustics
and personal listening preferences. The
following tips are intended to assist you at
using the controls in the best manner.
Please note that using the controls may
have a great impact on the overall sound
characteristics of your loudspeakers. We
recommend using the controls with utmost
care and only after several audio tests with
familiar recordings.
Tweeter Level
The ‘Tweeter Level’ works within the fre-
quency range of the tweeter (>2.500 Hz)
, raising or lowering up to ±4 dB. It alters
this frequency range as a whole (see fig.
7).
High / Low Shelf (Room EQs)
The other two controls operate in a differ-
ent manner. The ‘High Shelf’ and the ‘Low
Shelf’ are shelving filters, which progres-
sively raise or lower up to ±6 dB.
That means the shelve filters do not alter
a whole frequency band but alter in this
band: from a certain point (5kHz respec-
tively 300Hz in this case) the frequencies
are gradually being changed (see fig. 8).
5.1
5.2
5.3
fig.9: Tweeter Level
fig. 8: Controls
TWEETER LEVEL
A5X
LOW SHELFHIGH SHELF
OUTPUT
STEREOLINK
INPUT
UNBALANCED IN
BALANCED IN
CONTROLS
IN-/ OUTPUTS
0
-6 dB +6 dB
0
-6 dB +6 dB
0
-4 dB +4 dB
Serial No.
T1.6AL (230V~,50Hz)
T3AL (115V~,60Hz)
130WATTS
fig. 10: Room EQs

12
6.Troubleshooting
All ADAM products are designed and manufactured to the highest quality
standards. However, if any problems with your speaker occur, we recommend
to proceed as follows:
Problem: The LED shows normal operation (green) but there is either no or
only a distorted audio signal.
If both (all) speakers are affected, the reason can probably be found within
the signal path. If only one speaker is affected, the problem will probably be
within this speaker.
Check the wiring
Is the cable defective? Are all cables connected correctly?
Check the signal path
Interchange the cables of both loudspeakers. Does the problem change with
one of the cables?
Connect the monitor as directly to the signal source as possible (please mind
the volume!). Is another part of the signal path (e.g. mixer, subwoofer) defec-
tive?
If the answer to all these question is ‘no’, the problem is being caused by the
loudspeaker with the utmost probability.
If the answer to at least one of these questions is ‘yes’, there will probably be
another defective device within the signal path.
Problem: You hear parasitic noises (like humming, buzzing, soughing,
cracking).
Please disconnect the signal cables.
If the noises disappear, check the signal path.
If the noises can still be heard, check for other electrical devices close to
the speakers (mobile phones, switching power supplies, etc.). If there is no
interfering device the speaker will probably cause the problem.
6.1
6.2
a)
b)

13
English
7.Maintenance
Please switch the loudspeaker off before cleaning!
Please note that the diaphragms build up a magnetic field. Do not ply with
magnetic items at close range to the diaphragms.
Please make sure that no liquids get inside the cabinet. Do not spray any
fluids on the speaker. Do not use a wet cloth for cleaning.
Do not use flammable or acidly chemicals for cleaning.
Do not touch the membranes of the loudspeakers.
We recommend using a lint-free, damp cloth for cleaning.
The loudspeaker membranes may be dusted using a very soft brush.
8. Transport / Package
In case you have to send your speakers to any other location, it is of vital
importance that you use the original packaging materials. Experience has
shown that it is very difficult to avoid damage if you have to send them with-
out these. ADAM Audio can not be held responsible for damages due to im-
proper packaging.
If a transport is necessary and the original package is no more available, a
new one can be purchased from ADAM Audio.
9. Environmental Information
All ADAM products comply with international directives on the Restriction of
Hazardous Substances (RoHS) in electrical / electronical equipment and the
disposal of Waste Electrical / Electronic Equipment (WEEE).
For disposal, please consult your local authorities for further information.

14
10. EU Declaration of Conformity
We,
ADAM Audio GmbH
whose registered office is situated at
Ederstr. 16, 12059 Berlin, Germany
declare under our sole responsibility that the product:
A5X
complies with the EU Electro-Magnetic Compatibility (EMC) Directive
89/336/EEC, in pursuance of which the following standards have been ap-
plied:
EN 61000-6-1 : 2001
EN 61000-6-3 : 2001
EN 55020 : 2002
EN 55013 : 2001
and complies with the EU General Product Safety 2001/95/EC, in pursuance
of which the following standard has been applied:
EN 60065 : 2002.
This declaration attests that the manufacturing process quality control and
product documentation accord with the need to assure continued compli-
ance.
The attention of the user is drawn to any spezial measures regarding the use
of this equipment that may be detailed in the owner’s manual.
Signed:
Roland Stenz
Director
ADAM Audio

15
English
11.1
d)
a)
b)
c)
e)
11.2
11. Warranty
ADAM Audio GmbH provides a five year limited warranty for this product.
Terms and Conditions
This warranty is limited to the repair of the equipment or, if necessary, the
replacement of parts or the product and return shipping within the country
of purchase.
This warranty complements any national/regional law obligations of deal-
ers or national distributors and does not affect your statutory rights as a
customer.
Neither other transportation, nor any other costs, nor any risk for removal,
transportation and installation of products is covered by this warranty.
Products whose serial number have been altered, deleted, removed or made
illegible are excluded from this warranty.
The warranty will not be applicable in cases other than defects in materials
and/or workmanship at the time of purchase and will not be applicable:
for damages caused by incorrect installation, connection or packing,
for damages caused by any use other than correct use described in the user
manual,
for damages caused by faulty or unsuitable ancillary equipment,
if repairs or modifications have been executed by an unauthorized person,
for damages caused by accidents, lightning, water, fire heat, public distur-
bances or any other cause beyond the reasonable control of ADAM Audio.
How to claim repairs under warranty
Should service be required, please contact the ADAM Audio dealer where
the product has been purchased.
If the equipment is being used outside the country of purchase, the interna-
tional shipping costs have to be paid for by the owner of the product.
Service may be supplied by your ADAM Audio national distributor in the coun-
try of residence. In this case, the service costs have to be paid for by the
owner of the product whereas the costs for parts to be repaired or replaced
are free of charge. Please visit our website to get the contact details of your
local distributor.
To validate your warranty, you will need a copy of your original sales invoice
with the date of purchase.

16
12. Technical Data/Technische Daten
A5X. Active Nearfield Monitor/Aktiver Nahfeldmonitor
Tweeter/Hochtöner X-ART
Velocity transfer ratio/Geschwindigkeit-
stransformation 4:1
Equivalent diaphragm/Äquivalente Membran
ø56 mm / 2“
Woofer/Tieftöner 145 mm / 5.5“
Woofer material/Tieftöner Membranmaterial Carbon fiber/Rohacell/Glass fiber
Built-in amplifiers/Eingebaute Verstärker 2
Nominal voltage/Nennspannung 100 -120 V~, 50/60 Hz 3
220 - 240 V~, 50/60 Hz 3
Woofer channel/Tieftöner 1/2 50 W / 75 W
Tweeter channel/Hochtöner 1/2 50 W / 75 W
Control Panel
Input Sensitivity/Lautstärke -∞ to +14 dB
Tweeter gain/Hochtonpegel ± 4 dB
EQ > 5 kHz ± 6 dB
EQ < 300 Hz ± 6 dB
General Data
Frequency response/Frequenzgang 50 Hz - 50 kHz
THD 90dB/1m >100 Hz ≤ 0,6%
SPL with sine wave 100 Hz to 3 kHz in 1m ≥ 102 dB
Max. peak acoustic output in 1m per pair ≥ 110 dB
Crossover frequency/Übergangsfrequenz 2.500 Hz
Inputs/Eingänge XLR / RCA
Input impedance/Eingangsimpedanz 30 kΩ
Weight/Gewicht 6.6 kg / 14.6 lb.
Magnetically shielded/magnetisch geschirmt no
Height x Width x Depth/Höhe x Breite x Tiefe 280 x 170 x 220 mm / 11“ x 6.5“ x 8.5“
Warranty/Garantie 5 years/5 Jahre
Operating temperature/Betriebstemperatur 0° C to 40° C (32° F to 104° F)
Storage temperature/Lagertemperatur -30° C to 70° C (-22° F to 167° F)
Humidity/Luftfeuchtigkeit Max. 90 % not condensing/nicht konden-
sierend
1=longtermIEC265-8-Wrms/10min
2=nominalIEC265-8=PeakPower5µsec
3=payattentiontotheselectedvoltageontherearsideofthespeaker

A5X Nahfeld-Monitor
Bedienungsanleitung
deutsch
A5X

18
Sicherheitshinweise
Bitte beachten Sie die folgenden Sicherheitshinweise, bevor Sie
Ihre neuen Lautsprecher in Betrieb nehmen. Bitte heben Sie diese
Anleitung auf. Bitte beachten Sie alle Warnungen und folgen Sie allen
Anweisungen.
Achtung: Um die Gefahr eines Stromschlages zu vermeiden, öffnen Sie
die Monitore nicht. Es befinden sich keine wartungsbedürftigen Teile
im Gehäuseinnern. Bitte versuchen Sie auf keinen Fall, dieses Produkt
selbst zu reparieren und wenden Sie sich bei einem Problemfall an
qualfiziertes Servicepersonal.
Die Lautsprecher müssen mit einer dreipoligen, geerdeten Stromversorgung
betrieben werden. Alle drei Pole müssen stets verwendet werden. Dies gilt
auch für davor geschaltete Verlängerungen oder Verteiler.
Verwenden Sie ausschließlich die spezifizierten Sicherungstypen.
Überbrücken Sie niemals, auch nicht im Notfall, die Sicherung.
Überprüfen Sie, ob die gekennzeichnete Nennspannung mit der
Nennspannung in Ihrer Umgebung übereinstimmt. Sollte dies nicht der Fall
sein, schließen Sie die Lautsprecher in keinem Falle an eine Stromquelle an
und kontaktieren Sie Ihren Fachhändler.
Schalten Sie stets alle Geräte aus, bevor Sie eine Kabelverbindung
entfernen oder neu hinzufügen.
Verwenden Sie nur Wagen, Ständer, Stative, Einbauhilfen oder Tische,
die vom Hersteller empfohlen oder die mit dem Gerät geliefert werden.
Bewegen Sie einen Wagen, auf dem das Gerät steht, vorsichtig, um ein
Herabstürzen zu verhindern.
Erklärung der graphischen Symbole
Das Blitzsymbol warnt vor der Gefahr eines
elektrischen Schlages.
Das Ausrufezeichen weist auf wichtige
Bedienungs- oder Pflegehinweise hin.
Achtung
Gefahr durch Stromschlag
Nicht öffnen
UM DIE GEFAHR EINES STROMSCHLAGES ZU VERRINGERN,
ENTFERNEN SIE WEDER DIE RÜCKWAND NOCH SONSTIGE TEILE.
DIE INNEREN BAUTEILE DÜRFEN NICHT VOM ANWENDER, SONDERN
NUR VON QUALIFIZIERTEM FACHPERSONAL GEWARTET WERDEN.
SETZEN SIE DAS GERÄT WEDER REGEN NOCH FEUCHTIGKEIT AUS.

19
Deutsch
Sicherheitshinweise
Vermeiden Sie, dass Flüssigkeiten jeglicher Art ins Gehäuseinnere gelangen.
Sprühen Sie weder Flüssigkeiten direkt auf das Gerät, noch nutzen Sie
nasse Reinigungslappen.
Bitte verwenden Sie keine brennbaren und ätzenden Chemikalien zur
Reinigung dieses Produkts (siehe 7.).
Vermeiden Sie jede Berührung mit den Membranen der Lautsprecher und
blockieren Sie nicht die Bassreflexöffnung.
Gewährleisten Sie eine rückwärtige Luftabfuhr für eine notwendige Kühlung
der Elektronik.
Zum Trennen des Gerätes vom Stromnetz schalten Sie den Netzschalter
aus. Anschließend ziehen Sie den Netzstecker aus der Steckdose. Der
Netzschalter und -stecker müssen leicht erreichbar sein.
Verwenden Sie stets geprüfte Kabel. Defekte Kabel sind häufig die Ursache
für Störgeräusche verschiedener Art.
Setzen Sie dieses Produkt nicht bei extremen Temperaturen ein, ebenso
wenig in feuer- oder explosionsgefährdeten Umgebungen.
Bitte beachten Sie, dass im Gehäuseinneren sich Magnete befinden,
die ein Magnetfeld aufbauen. Vermeiden Sie, mit magnetischen bzw.
paramagnetischen Gegenständen in unmittelbare Nähe der Lautsprecher zu
hantieren.
Zu hohe Lautstärken können ihr Gehör schädigen! Vermeiden Sie direkte
Nähe zu Lautsprechern, die mit hohen Pegeln betrieben werden.

20
Inhalt
Sicherheitshinweise ................................18-19
1. Einleitung ................................................21
2. Quick Start zur Inbetriebnahme ..............22
2.1 Allgemeine Hinweise ...............................22
2.2 Quick Start / Inbetriebnahme.................22
3. Anschluss der Lautsprecher....................23
3.1 Normaler Anschluss ................................23
3.2 Stereo Link..............................................23
4. Empfehlungen zur Aufstellung .................24-26
4.1 Vertikale Aufstellung ...............................24
4.2 Horizontale Aufstellung ...........................24
4.3 Hochtöner in Ohrenhöhe.........................25
4.4 Zweikanal Stereo.....................................25
4.5 Mehrkanal (Surround) .............................26
4.6 Ständer- oder Wandbefestigung..............26
5. Lautsprechereinstellungen ......................27
5.1 Kontrollpanel...........................................27
5.2 Tweeter Level (Hochtonpegel) .................27
5.3 Raum EQs (Shelve Filter).........................27
6. Fehlerbehebung ......................................28
6.1 Kein oder gestörtes Signal ......................28
6.2 Nebengeräusche .....................................28
7. Wartung und Pflege.................................29
8. Transport / Verpackung..........................29
9. Umweltinformation..................................29
10.Konformitätsbescheinigung.....................30
11. Garantie ..................................................31
11.1 Garantiebedingungen..............................31
11.2 Inanspruchnahme ...................................31
12. Technischen Daten..................................16