Adaptive Technologies Group MultiMount MM-120 User manual

MM-120
REV00-11012015
1 of 3
Installation Guide
Adjustable Wall Mount
U-Bracket will be attaching to the rear or the bottom speaker, then
The versatile MultiMount™ MM-120 wall mounts hold a loudspeakers
weighing up to 120 lbs to walls by securing to standard four-holes mounting
patterns located on the back and the bottom panels.
versatile range of mounting and aiming options
Assemble the Pivot U-Bracket to the set of holes closest to the bracket pivot
using the supplied ¼-20 x5” long screws.
Assemble the Pivot U-Bracket to the set of holes farthest from the bracket
pivot using the supplied ¼-20 x5” long screws.
Note to installers
Due to the wide variety of wall structures, materials and mounting
methods, these instructions assume that the installing contractor will
exercise proper judgment in selecting the mounting area and hardware.
As a guide, the installation, when complete should be capable of
supporting 5 to 10 times the actual applied load. Always use a back up
safety system such as a safety cable.
To assure a trouble free installation, read through and follow these
instructions carefully before beginning. If you have doubts about
the integrity of the structure you are mounting to or you are not sure
about the proper hardware to use, consult a structural and/or
hardware specialist.
Be sure that all of the following items are included in this kit before proceeding:
1 pc Wall mounting plate 1 pc Speaker adapter assembly
1 pc Hardware kit bag 1 pc Instruction sheet
Note: Screws and washers to attach speaker to adapter plate are not included

MM-120
REV00-11012015
2 of 3
Installation Guide
Adjustable Wall Mount
Steps for mounting the MM-120 to the Wall and Speaker
Step 1: Disassemble the wall plate
This will allow the wall plate to be mount to the wall with no interference
(Figure 1).
Step 2: Install wall plate to wall
Install the wall plate to the wall using the 4 corner holes of the wall plate. Use
and place over the desired wall location. Use appropriate mounting screws
for the proper wall structure. (Figure 2).
Do not invert the wall plate. The gusset tab must be always on the
bottom side.
Step 3a: Install the speaker adapter to rear of speaker
Owner using their own hardware to mount the speaker plate to the speaker
(Figure 3).
Step 3b: Assemble the speaker adapter to a bottom of speaker
Owner using their own hardware to mount the speaker plate to the speaker
(Figure 4).
Step 3c: Attach mount to speaker
Attach the speaker mount to the selected speaker mounting holes using the
speaker manufacturer’s recommended or supplied hardware (Not included
with the mount). Tighten these fasteners permanently (Figure 3 and Figure 4).
Note: If the speaker cabinet does not offer threaded mounting holes, do not
install this mount. Consult the speaker manufacturer for their recommended
mounting procedures.
Step 4: Attach speaker & mount assy
to the wall plate then secure with the binding post screw (Figure 1).
Step 5: Set the pan angle on the pivot bracket
Loosen and adjust the hex bolt. This enables the panning of the speaker
from left to right. Tighten this bolt to lock it in place. (Figure 5 & 9).
Figure 1
Figure 2
Figure 3
Figure 4 Figure 5
Figure 3

MM-120
ALWAYS INSTALL SAFETY CABLES
WARNING: Mounting and/or suspension loudspeakers requires experienced
professionals. Improperly installed loudspeakers can result in property
damage, personal injury and/or liability to the installing contractor.
Adaptive Technologies Group
1635 E. Burnett Street | Signal Hill, CA 90755 USA
Ph: 562.424.1100 | Fax: [phone]
www.adapttechgroup.com
REV00-11012015
3 of 3
Installation Guide
Adjustable Wall Mount
Step 6: Set the tilt angle
Rotate the adjustment screw to aadjust the tilt angle of the speaker
(Figure 6).
Step 7: Install speaker and mount to wall plate
Lift speaker and mount up to the wall mounting plate, feed wire in
through the end of the support arm tube and out through the tube’s
upper hole (Figure 7, 8 & 9).
Step 8: Strongly recommended: Install safety cable
Attach one end of a safety to the wall structure and the other end to
the speaker. If no attachment is provided on the speaker, consult the
speaker manufacturer for advice on best attachment point on method.
Safety cables sold separately.
Figure 6
Figure 7
Figure 9
Figure 8
Showing u-bracket in the bottom
mounting position and pivot point
Showing u-bracket in the rear
mounting position and pivot point