Bosch FlexiDome VDA-CMT-Dome User manual

FlexiDome Corner Mount
VDA-CMT-Dome
en Installation manual

FlexiDome Corner Mount Safety | en 3
Bosch Security Systems Installation manual | v2.0 | 2011.08
1Safety
1.1 Safety precautions
1.2 Important safety instructions
Read, follow, and retain for future reference all of the following safety instructions. Heed all
warnings on the unit and in the operating instructions before operating the unit.
1. Safety check - Safety checks should be performed upon completion of service or repairs
to the unit to ensure proper operating condition.
2. Installation - Install in accordance with the manufacturer's instructions and in
accordance with applicable local codes.
3. Attachments, changes or modifications - Only use attachments/accessories specified by
the manufacturer. Any change or modification of the equipment, not expressly approved
by Bosch, could void the warranty or, in the case of an authorization agreement, authority
to operate the equipment.
1.3 Important notices
Environmental statement - Bosch has a strong commitment towards the environment. This
unit has been designed to respect the environment as much as possible.
More information
For more information please contact the nearest Bosch Security Systems location or visit
www.boschsecurity.com
WARNING!
Medium risk: Indicates a potentially hazardous situation.
If not avoided, this could result in minor or moderate bodily injury.
CAUTION!
Low risk: Indicates a potentially hazardous situation.
If not avoided, this could result in property damage or risk of damage to the unit.
Disposal - Your Bosch product was developed and manufactured with high-quality material
and components that can be recycled and reused. This symbol means that electronic and
electrical appliances, which have reached the end of their working life, must be collected and
disposed of separately from household waste material. Separate collecting systems are
usually in place for disused electronic and electrical products. Please dispose of these units
at an environmentally compatible recycling facility, per European Directive 2002/96/EC.
WARNING!
For a secure installation use stainless steel or zinc plated fasteners.
CAUTION!
If these mounts are used outdoors ensure that the equipment they are used with is also
suitable for outdoor use.

FlexiDome Corner Mount Unpacking | en 4
Bosch Security Systems Installation manual | v2.0 | 2011.08
2 Unpacking
Unpack carefully and handle the equipment with care. The packaging contains:
–Mount
– Hardware kit
If equipment has been damaged during shipment, repack it in the original packaging and
notify the shipping agent or supplier.The shipping carton is the safest container to transport
the unit. Save it for possible future use.

FlexiDome Corner Mount Installation | en 5
Bosch Security Systems Installation manual | v2.0 | 2011.08
3 Installation
This installation should be made by qualified service personnel and conform to the National
Electrical Code and applicable local codes.
3.1 Installing the Corner Mount
Figure 3.1 Corner Mount Disassembly
1. Disassemble housing by releasing security screw [3] on bottom of unit using provided
security wrench, then pull front cover [1] off rear cover [2].
2. Determine location for corner mount.
3. Using rear cover [2] of mount as template, mark location of mount holes on walls.
4. Drill holes for anchors and install anchors into wall.
5. Decide which conduit hole to use and plug remaining openings using two (2) plugs
(provided with hardware kit). Secure conduit plug on top of unit by tightening set screw
on back of rear cover [2]. This step must be performed before rear cover [2] is secured
to wall. Use a 2.5 mm Hex Key (not supplied).
6. If a side feed-through is chosen, mark hole using rear cover as template. Drill hole into
wall. Use this hole to pull wires into bracket.
7. Assemble rear cover [2] of mount to wall.
8. Pull all wires from wall through feed-through hole.
9. Assemble camera to front cover [1] and fix with three (3) M5 screws (supplied).
10. Install the camera dome housing cover.
11. Connect all wires to camera.
12. Pull any excess wires back into mount.
13. Slide front cover [1] onto rear cover [2] and secure with security screw [3].
1 Front cover
2Rearcover
3 Security screw
3
2
1

FlexiDome Corner Mount Installation | en 6
Bosch Security Systems Installation manual | v2.0 | 2011.08
3.2 Corner mount assembly
The figure below illustrates the corner mount assembly:
Figure 3.2 Corner mount assembly
Note:
The rear cover provides three ¾-inch conduit openings. Install the ¾-inch conduit fittings as
needed for the installation.

FlexiDome Corner Mount Dimensional outlines | en 7
Bosch Security Systems Installation manual | v2.0 | 2011.08
4 Dimensional outlines
The following illustration depicts the dimensional outlines for the corner mount.
Figure 4.1 VDA-CMT dimensions

Bosch Security Systems
www.boschsecurity.com
© Bosch Security Systems, 2011