Adaptive Technologies Group SAS-2WA-Series User manual

Installation Guide SAS-2WA-SERIES
Installation Instructions for SAS-2WA-48, SAS-2WA-66 and SAS-2WA-86
The Two Way Array is a load rated overhead suspension
beam used for ying two loudspeaker cabinets and other
objects equipped with safe rigging points. This rigging system
allows for single and multiple tiered applications.
As a guide, the installation, when completed should be
capable of supporting at least 5 times the actual
applied load. Do not exceed the beam’s working load
limit. Use only Grade 8 hardware. If creating a grid, do
not exceed the grid’s working load limit.
Contents:
Be sure that all of the following items are included in this kit before proceeding:
1 pc. Rigging Beam (2 x 4 x 48”, 66” or 86” long)
2 pcs. Gridlink Cross Arms
1 pc. Hardware Kit
Installation Procedure:
Step 1: Check Cross Arm Placement:
If you need to move the cross arms towards the center or
farther away from the center, remove the nylock nuts, bolts
and at washers from the cross arm. Select the desired
holes then reassemble the cross arms to the rigging beam
using the same hardware and in the same order (Figure 2).
Be sure the cross arms are moved equally to keep the system
balanced and symmetrical.
Step 3: Prepare the Two Way Array Rigging System
Install the outer suspension eyebolts, at washers, and nylock nuts through the
outer holes of the beam with the eye of the eyebolt on the top side of the beam,
opposite the Cross Arms. Tighten permanently but do not crush tube (Figure
1A).
For multiple tiered applications, fasten eye nuts under the eyebolts then the
nylock nut (Figure 1B). Make sure the eyes of the eyebolts are perpendicular to
the length of the beam (Figure 1A/B). Tighten permanently but do not crush
tube.
EYEBOLTS
WASHER
WASHER
WASHER
WASHER
EYEBOLT
EYENUT
NYLOCK NUT
1/4-20 EYEBOLT
CROSS BAR
END CAP
1/4-20 NUT
1/4-FLAT WASHER
END CAP
1/4 FLAT WASHER
1/4-20 SCREW
COTTER PIN
2” FRINCTION WASHER
CROSS BAR
1/2-13 NYLOCK NUT
1/2-FLAT WASHER
1/2-FLAT WASHER
1/2-HEX BOLT
COTTER PIN
2” NYLON WA SHER
CROSS BAR
1/2 X 7 HEX BOLT
1/2 FLAT WASHER
1/2-13 NYLOCK NUT
1/2 FLAT WASHER
EYEBOLTS
WASHER
WASHER
WASHER
WASHER
EYEBOLT
EYENUT
NYLOCK NUT
1/4-20 EYEBOLT
CROSS BAR
END CAP
1/4-20 NUT
1/4-FLAT WASHER
END CAP
1/4 FLAT WASHER
1/4-20 SCREW
COTTER PIN
2” FRINCTION WASHER
CROSS BAR
1/2-13 NYLOCK NUT
1/2-FLAT WASHER
1/2-FLAT WASHER
1/2-HEX BOLT
COTTER PIN
2” NYLON WASHER
CROSS BAR
1/2 X 7 HEX BOLT
1/2 FLAT WASHER
1/2-13 NYLOCK NUT
1/2 FLAT WASHER
Adaptive Technologies Group
1635 E. Burnett Street | Signal Hill, CA 90755 USA
Ph: 562.424.1100 | Fax: [phone]
www.adapttechgroup.com
ALWAYS INSTALL SAFETY CABLES
WARNING: Mounting and/or suspension of audio and video equipment requires
experienced professionals. Improperly installed loudspeakers can result in property
damage, personal injury and/or liability to the installing contractor.
EYEBOLTS
WASHER
WASHER
WASHER
WASHER
EYEBOLT
EYENUT
NYLOCK NUT
1/4-20 EYEBOLT
CROSS BAR
END CAP
1/4-20 NUT
1/4-FLAT WASHER
END CAP
1/4 FLAT WASHER
1/4-20 SCREW
COTTER PIN
2” FRINCTION WASHER
CROSS BAR
1/2-13 NYLOCK NUT
1/2-FLAT WASHER
1/2-FLAT WASHER
1/2-HEX BOLT
COTTER PIN
2” NYLON WA SHER
CROSS BAR
1/2 X 7 HEX BOLT
1/2 FLAT WASHER
1/2-13 NYLOCK NUT
1/2 FLAT WASHER
Figure 1A Figure 1B
Figure 2

Installation Guide SAS-2WA-SERIES
Installation Instructions for SAS-2WA-48, SAS-2WA-66 and SAS-2WA-86
Adaptive Technologies Group
1635 E. Burnett Street | Signal Hill, CA 90755 USA
Ph: 562.424.1100 | Fax: [phone]
www.adapttechgroup.com
ALWAYS INSTALL SAFETY CABLES
WARNING: Mounting and/or suspension of audio and video equipment requires
experienced professionals. Improperly installed loudspeakers can result in property
damage, personal injury and/or liability to the installing contractor.
NOTE:
For U-Bracket
Remove cross arm as in step 1, install the U-Bracket to the Cross Arm
then reassemble the cross arm to the rigging beam using the same
hardware and in the same order.
Step 3: Prepare Cross Arm for Rigging
(Adjustable Tilt Cable Kit), install the 5/16” eyebolts to the bottom holes
at the end of the cross arm using  at washers and nylock nuts. Tighten
permanently. Press fi t the end caps on the ends of the cross arm tube.
(Figure 3A).
Prepare Cross Arm for U-Bracket
Attach the U-bracket to the four holes underneath the cross arm
using the provided ¼” x ¾” long screws,  at washers and nylock nuts.
Tighten permanently (Figure 3B). Attach the Cross Arm/U-Bracket
assembly to the beam using the ½ x 7” hex bolt, friction washer,  at
washer, nylock nut and cotter pin. See U-Bracket instruction sheet for
more details.
Step 4: Suspen Two Way Array
Suspend the Two�Way�Array from the selected suspension points using
the two eyebolts on each side of the beam. The hang angle should
be as close to vertical as possible. Make sure that the combined
suspension points are capable of supporting at least 5 times the weight
of the entire load (fi gure 4).
For multiple Tiered applications, use eye nuts (sold separately
underneath the beam’s eyebolts as a hang point with rated shackles,
cables and/or chain. (Figure 1B). Make sure the eyes of the eyebolts
and eye nuts are perpendicular to the beam’s length (Figure 4).
Step 5: Attach Rigging Hardware
Suspend the selected loudspeaker and rigging hardware (Tilt cable kit
or U-Bracket) from the eyebolts underneath the cross arms using, load
rated shackles, cables or other load rated fasteners (Figure 5).
Step 6: Adjusting the Horizontal Angle
Rotate the cross arm from the beam until the desired horizontal angle
is achieved. Repeat the procedure to the other cross arm (Figure 6).
Step 7: Adjusting the Tilt Angle:
See Adjustable Tilt Cable Kit or U-Bracket instruction sheet for more
details.
Before hoisting, lift entire system a short distance and check each
and every connection thoroughly before proceeding.
EYEBOLTS
WASHER
WASHER
WASHER
WASHER
EYEBOLT
EYENUT
NYLOCK NUT
1/4-20 EYEBOLT
CROSS BAR
END CAP
1/4-20 NUT
1/4-FLAT WASHER
END CAP
1/4 FLAT WASHER
1/4-20 SCREW
COTTER PIN
2” FRINCTION WASHER
CROSS BAR
1/2-13 NYLOCK NUT
1/2-FLAT WASHER
1/2-FLAT WASHER
1/2-HEX BOLT
COTTER PIN
2” NYLON WA SHER
CROSS BAR
1/2 X 7 HEX BOLT
1/2 FLAT WASHER
1/2-13 NYLOCK NUT
1/2 FLAT WASHER
EYEBOLTS
WASHER
WASHER
WASHER
WASHER
EYEBOLT
EYENUT
NYLOCK NUT
1/4-20 EYEBOLT
CROSS BAR
END CAP
1/4-20 NUT
1/4-FLAT WASHER
END CAP
1/4 FLAT WASHER
1/4-20 SCREW
COTTER PIN
2” FRINCTION WA SHER
CROSS BAR
1/2-13 NYLOCK NUT
1/2-FLAT WASHER
1/2-FLAT WASHER
1/2-HEX BOLT
COTTER PIN
2” NYLON WA SHER
CROSS BAR
1/2 X 7 HEX BOLT
1/2 FLAT WASHER
1/2-13 NYLOCK NUT
1/2 FLAT WASHER
EYEBOLTS
WASHER
WASHER
WASHER
WASHER
EYEBOLT
EYENUT
NYLOCK NUT
1/4-20 EYEBOLT
CROSS BAR
END CAP
1/4-20 NUT
1/4-FLAT WASHER
END CAP
1/4 FLAT WASHER
1/4-20 SCREW
COTTER PIN
2” FRINCTION WASHER
CROSS BAR
1/2-13 NYLOCK NUT
1/2-FLAT WASHER
1/2-FLAT WASHER
1/2-HEX BOLT
COTTER PIN
2” NYLON WA SHER
CROSS BAR
1/2 X 7 HEX BOLT
1/2 FLAT WASHER
1/2-13 NYLOCK NUT
1/2 FLAT WASHER
EYEBOLTS
WASHER
WASHER
WASHER
WASHER
EYEBOLT
EYENUT
NYLOCK NUT
1/4-20 EYEBOLT
CROSS BAR
END CAP
1/4-20 NUT
1/4-FLAT WASHER
END CAP
1/4 FLAT WASHER
1/4-20 SCREW
COTTER PIN
2” FRINCTION WA SHER
CROSS BAR
1/2-13 NYLOCK NUT
1/2-FLAT WASHER
1/2-FLAT WASHER
1/2-HEX BOLT
COTTER PIN
2” NYLON WA SHER
CROSS BAR
1/2 X 7 HEX BOLT
1/2 FLAT WASHER
1/2-13 NYLOCK NUT
1/2 FLAT WASHER
Figure 3B
Figure 3C
Figure 5
Figure 3A
Figure 4
Figure 6
EYEBOLTS
WASHER
WASHER
WASHER
WASHER
EYEBOLT
EYENUT
NYLOCK NUT
1/4-20 EYEBOLT
CROSS BAR
END CAP
1/4-20 NUT
1/4-FLAT WASHER
END CAP
1/4 FLAT WASHER
1/4-20 SCREW
COTTER PIN
2” FRINCTION WASHER
CROSS BAR
1/2-13 NYLOCK NUT
1/2-FLAT WASHER
1/2-FLAT WASHER
1/2-HEX BOLT
COTTER PIN
2” NYLON WASHER
CROSS BAR
1/2 X 7 HEX BOLT
1/2 FLAT WASHER
1/2-13 NYLOCK NUT
1/2 FLAT WASHER