Advantech-DLoG DLT-V72 Series User manual

Mounting instructions: Attaching the scanner holder to the DLT-V72 / DLT-V83
Advantech Co., Ltd Mounting instructions: Attaching the scanner holder to the DLT-V72 / DLT-V83, V3.00, PN 20080V7231 Page 1 / 4
1 For your safety
These mounting instructions apply to all DLT-V72 and DLT-V83 models. They describe
how to attach the appropriate Advantech-DLoG scanner mounting kit.
Read and observe the mounting instructions carefully.
Keep them for future reference.
WARNING
Risk of injury due to weight and sharp-edged parts.
The DLT-V72 / DLT-V83 can fall down and cause injuries due to its weight. The
strain relief rail can have sharp edges and cause cutting injuries.
Always hold the device by the housing with both hands.
Never use the antenna cap as a handle. It can break due to the weight
involved.
Do not hold the device by the strain relief rail.
Use the assistance of a second person for installation work.
WARNING
Risk of injury and damage due to improper installation
These mounting instructions are intended for skilled personnel. Only qualified
skilled personnel may mount/install DLT-V72 / DLT-V83 devices
1.1 Tools required
−Allen key (5 mm width for M6)
−Socket wrench (size 7)
1.2 Installation sequence
If the DLT-V72 / DLT-V83 is being used with a mounting bracket and a scanner
mounting kit:
First attach the mounting bracket to the DLT-V72 / DLT-V83.
Then attach the scanner holder.
Not until then, mount the complete system at the deployment location, e.g. to the
forklift.
Please note: In addition to the mounting bracket, one accessory holder each can be
attached (on each side).

Mounting instructions: Attaching the scanner holder to the DLT-V72 / DLT-V83
Advantech Co., Ltd Mounting instructions: Attaching the scanner holder to the DLT-V72 / DLT-V83, V3.00, PN 20080V7231 Page 2 / 4
2 Scanner holder assembly
Assemble the scanner holder from the following components as shown in figure.
Adjust according to the scanner size.
Please note: Die intermediate screw (position of figure: 20) is only required for the
DLT-V83, not for the DLT-V72.
Position
of figure
Number
of
parts
Parts description
10 3 Cylinder-head screw DIN 912 - M6 x 10 - A2, Tuflok
20 3 Washer ISO 8738 - A6-A2
30 4 Nut, M4 bevel washer
40 1 Scanner holder
50 1 Spring clip
60 1 Spring clip, complete
70 1 Hand scanner connection plate
80 2 Protection cap

Mounting instructions: Attaching the scanner holder to the DLT-V72 / DLT-V83
Advantech Co., Ltd Mounting instructions: Attaching the scanner holder to the DLT-V72 / DLT-V83, V3.00, PN 20080V7231 Page 3 / 4
3 DLT-V72: Attaching the scanner holder
Note
The figure shows the attachment of the scanner holder on the left; the
attachment on the right is done analogously but mirror inverted.
DLT-V72:
Fasten scanner
holder.
4 DLT-V83: Attaching the scanner holder
Note
The figure shows the attachment of the scanner holder on the left; the
attachment on the right is done analogously but mirror inverted.
DLT-V83:
Fasten
scanner
holder,
step 1.

Mounting instructions: Attaching the scanner holder to the DLT-V72 / DLT-V83
Advantech Co., Ltd Mounting instructions: Attaching the scanner holder to the DLT-V72 / DLT-V83, V3.00, PN 20080V7231 Page 4 / 4
DLT-V83:
Fasten scanner
holder, step 2.
5 Technical customer support
Service & Support
E-Mail: [e-mail]
Advantech Europe B.V.
Science Park Eindhoven 5708, 5692ER,
Son en Breugel,
The Netherlands
Internet: www.advantech.com
oder: www.advantech.eu
Attaching scanner holder to
DLT-V72 / DLT-V83
Mounting instructions V3.00
September 15, 2022
The contact details of our worldwide Advantech Service Centers can be found on our
website: https://erma.advantech.com
by Advantech Co., Ltd. 2015-2022
We reserve the right to make changes to these mounting instructions at any time and
without prior notice. Advantech accepts no liability for any technical or printing errors or
shortcomings in these instructions. Advantech accepts no liability for any damage
caused directly or indirectly by the delivery, performance or use of this material.