AEG Powertools BSS18C12ZB3 User manual

2
2

33
Important!
It is essential that you read the instructions in this manual
before assembling, operating, and maintaining the product.
Subject to technical modifications.

4
4
4
8
9
STOP START
6
10
5
10
Remove the bttery pack before starting any work on the machine.
Accessories are not included.
11

55
4
8
9
STOP START
6
10
5
10
Remove the bttery pack before starting any work on the machine.
Accessories are not included.
11

6
6
6
Remove the battery pack before
starting any work on the machine.
Accessories are not included.
2
1
click
1
2

77
6
Remove the battery pack before
starting any work on the machine.
Accessories are not included.
2
1
click
1
2
75-100 %
50-75 %
25-50 %
0-25 %

8
8
8
9
START
STOP

99
8
9
START
STOP

10
10
10
LOCK
11
Set the speed selector to the A
position for auto-tight mode*.
Applications:
■Tightening aluminium wheel nuts
on a car where lower torque is
required, so chance of damage
to wheel nuts is reduced.
Precision additional tightening
with torque wrench should be
used. Torque: Approx. 200Nm
■Tightening nut onto bolt through
hollow pipe or a material softer
than nut and bolt to reduce
damage to the surface.
*Auto-tight mode stops the product
within the rst second of impact.
Pre-testing of the auto-tight mode is
recommended before use.

11 11
10
LOCK
11

12
12
WARNING! Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric
shock, re and/or serious injury.
Save all warnings and instructions for future reference.
IMPACT WRENCH SAFETY WARNINGS
Hold power tool by insulated gripping surfaces, when
performing an operation where the fastener may contact
hidden wiring. Fasteners contacting a “live” wire may make
exposed metal parts of the power tool “live” and could give the
operator an electric shock.
Wear ear protectors. Exposure to noise can cause hearing loss.
Sawdust and splinters must not be removed while the machine is
running.
When working in walls ceiling, or  oor, take care to avoid electric
cables and gas or waterpipes.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or
by burning them. AEG Distributors offer to retrieve old batteries to
protect our environment.
Do not store the battery pack together with metal objects (short
circuit risk).
Use only System GBS chargers for charging System GBS battery
packs. Do not use battery packs from other systems.
Battery acid may leak from damaged batteries under extreme load
or extreme temperatures. In case of contact with battery acid wash
it off immediately with soap and water. In case of eye contact rinse
thoroughly for at least 10 minutes and immediately seek medical
attention.
SPECIFIED CONDITIONS OF USE
The cordless impact wrench may be used to tighten and loosen nuts
and bolts for independent use away from mains supply.
Do not use this product in any other way as stated for normal use.
BATTERIES
New battery packs reach full loading capacity after 4 - 5 chargings
and dischargings. Battery packs which have not been used for
some time should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance
of the battery pack. Avoid extended exposure to heat or sunshine
(risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged,
after used.
To obtain the longest possible battery life remove the battery pack
from the charger once it is fully charged.
For battery pack storage longer than 30 days:
• Store the battery pack where the temperature is below 27°C
and away from moisture.
• Store the battery packs in a 30% - 50% charged condition.
• Every six months of storage, charge the pack as normal.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods
TECHNICAL DATA BRUSHLESS IMPACT WRENCH BSS18C12ZB3
Rated voltage 18 V
Tool reception 1/2”
No-load speed
Low speed 0 - 1400 min-1
Middle speed 0 - 2000 min-1
High speed 0 - 2750 min-1
A speed(auto-tight mode) 0 - 2750 min-1
Impact rate (high speed) 3500 min-1
Max torque with battery (2.5 Ah) 426 Nm
Max torque with battery (6.0 Ah) 480 Nm
Max torque in auto-tight mode with battery (6.0 Ah) 200 Nm
Max diameter bolt / nut M18
Weight - not including battery pack 1.63 kg
BATTERY AND CHARGER
Compatible battery pack
(not included)
Compatible charger
(not included)
L1815R
L1820R
L1825R
L1830R
L1840R
L1850R
L1860R
AL1218G
BL1218
BLK1218
BL18DP-X5
Use AEG 18V battery and charger only

13 13
Legislation requirements.
Transportation of those batteries has to be done in accordance with
local, national and international provisions and regulations.
■The user can transport the batteries by road without further
requirements.
■Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation
and transport are exclusively to be carried out by appropriately.
trained persons and the process has to be accompanied by
corresponding experts.
When transporting batteries:
■Ensure that battery contact terminals are protected and
insulated to prevent short circuit.
■Ensure that battery pack is secured against movement within
packaging.
■Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
BATTERY PACK PROTECTION
The battery pack has overload protection that protects it from being
overloaded and helps to ensure long life. Under extreme stress the
battery electronics switch off the battery-lamp automatically. To
restart, switch the battery-lamp off and then on again. If the battery-
lamp does not start up again, the battery pack may have discharged
completely. In this case it must be recharged in the battery charger.
MAINTENANCE
The ventilation slots of the machine must be kept clear at all times.
Use only AEG accessories and AEG spare parts. Should
components need to be replaced which have not been described,
please contact one of our AEG service agents (see our list of
guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state
the Article No. as well as the machine type printed on the label and
order the drawing at your local service agents or directly at:
Techtronic Industries (Australia) Pty. Ltd.
PO Box 1065
Mount Waverley VIC 3149
Tel. no. 1300 361 505
Australia
Techtronic Industries N.Z. Ltd.
PO Box 12-806
Penrose AUCKLAND 1642
Tel no. 0800 279 624
New Zealand
SYMBOLS
Safety alert
Regulatory Compliance Mark (RCM). Product
meets applicable regulatory requirements.
Please read the instructions carefully before
starting the machine.
Hot surface
Do not dispose of electric tools together with
household waste material. Electric tools and
electronic equipment that have reached the end of
their life must be collected separately and returned
to an environmentally compatible recycling facility.

Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
Techtronic Industries (Australia) Pty. Ltd.
31 Gilby Road,
Mount Waverley VIC 3149,
Australia
Techtronic Industries N.Z. Limited
2 Landing Drive, Mangere,
Auckland, New Zealand 2022
961096250-01A