AEROCOMPACT COMPACTFLAT SN 2 User manual

USER MANUAL
COMPACTFLAT
SN 2 Mounting Gauge
VERSION: 01
LANGUAGE: ENGLISH | ORIGINAL LANGUAGE: GERMAN
IMPORTANT! READ CAREFULLY BEFORE USE!

CompactFLAT SN 2 Mounting Gauge 2
LEGAL NOTICE
The user manual is protected by copyright. This manual may not be copied, reproduced, microfilmed, translated, or con-
verted for storage and processing in computer systems, in whole or in part, without the written permission of
AEROCOMPACT®.
Copyright by © AEROCOMPACT®
MANUFACTURER
AEROCOMPACT® Holding
Sonnenstraße 10
A 6822 Satteins | Austria
[e-mail]
www.aerocompact.com
UPDATE
This manual is subject to change without notice. This does not represent any obligation on the part of the manufacturer.
CREATION DATE
02/2023

CompactFLAT SN 2 Mounting Gauge 3
TOC
Set up mounting gauge 4
Use mounting gauge to align the feet 4
Use mounting gauge to align base rails 5
Apply mounting gauge 6
Positioning the feet - SN 2 (5° or 10°) 6
Positioning the feet - SN 2 Plus 7
Positioning the base rail 8

CompactFLAT SN 2 Mounting Gauge 4
SET UP MOUNTING GAUGE
The mounting gauge can be used to align the base rails as well as the feet.
To insert the spacers, remove the end caps on one side. After inserting the spacers, reattach the end caps accordingly.
Use mounting gauge to align the feet
Insert the spacer (1) into the guide rail (2) and move it to the desired position. Then tighten with the locking screw (3).

CompactFLAT SN 2 Mounting Gauge 5
Use mounting gauge to align base rails
Insert the spacer (1) into the guide rail (2) and move it to the desired position. Then tighten with the locking screw (3).

CompactFLAT SN 2 Mounting Gauge 6
APPLY MOUNTING GAUGE
Positioning the feet - SN 2 (5° or 10°)
Mount the first three feet (1-3) according to the mounting instructions.
The correct spacing dimensions of the feet must be taken from the planning documents.
Place the mounting gauge according to the illustration and fix the spacer (distance A = 50 mm).
The adjusted mounting gauge can now be repositioned, applying the spacer from foot (1) to foot (3).
Position new feet and mount them afterwards.
The mounting gauge is now set for the SN 2 system and can be used as a gauge for the project.

CompactFLAT SN 2 Mounting Gauge 7
Positioning the feet - SN 2 Plus
Mount the first three feet (1-3) according to the mounting instructions.
The correct spacing dimensions of the feet must be taken from the planning documents.
Place the mounting gauge according to the illustration and fix the spacer (distance A = 50 mm).
The adjusted mounting gauge can now be repositioned, turning the mounting gauge 180° and placing it on the opposite
side, leaving the two spacers (2) and (3) between the two rear feet (see illustration).
Depending on the type of clamp, the relevant spacer (1) must be selected:
Short-side clamping: B = 31 mm
Long-side clamping: B = 23 mm
Position the front feet on both sides of the spacer (1) and fix them in place.
The mounting gauge is now set for the SN 2 Plus System and can be used as a gauge for the project.

CompactFLAT SN 2 Mounting Gauge 8
Positioning the base rail
Determine the distances between the base rails.
The correct spacing dimensions of the base rails must be taken from the planning documents.
Place the mounting gauge according to the illustration and fix the spacer.
The adjusted mounting gauge can now be repositioned, with the spacer of base rail (1) being placed at base rail (3).
Apply the mounting gauge along the base rails several times so that the base rails are aligned parallel.
Place the two new base rails.
The mounting gauge is now set and can be used as a gauge for the project.