AG Neovo SC-17AH User manual

SC-Series Analog HD-over-Coax Display
User Manual

TABLE OF CONTENTS
2
Contents
FCC Declaimers ....................................................................................................................................... 4
WEEE....................................................................................................................................................... 5
Notice ....................................................................................................................................................... 6
Cautions When Setting Up....................................................................................................................... 6
Cautions When Using............................................................................................................................... 7
Cleaning and Maintenance....................................................................................................................... 8
Notice for the LED-Backlit Display ........................................................................................................... 8
CHAPTER 1: PRODUCT DESCRIPTION..........................................................................9
1.1 Package Contents.............................................................................................................................. 9
1.2 Installation .......................................................................................................................................... 10
1.2.1 Installing the Stand.................................................................................................................. 10
1.2.2 Adjusting the Tilt and Rotation................................................................................................. 11
1.2.3 Removing the Stand................................................................................................................ 12
1.2.4 Wall Mounting.......................................................................................................................... 13
1.3 LED-Backlit Display Overview............................................................................................................ 15
1.3.1 Front View and Control Buttons............................................................................................... 15
1.3.2 Rear View................................................................................................................................ 17
1.4 Remote Control (for SC-32AH/SC-42AH model only)..................................................................... 18
1.4.1 Remote Control Buttons .......................................................................................................... 18
1.4.2 Installing the Remote Control Batteries................................................................................... 19
CHAPTER 2: MAKING CONNECTIONS...........................................................................20
2.1 Connecting the AC Power .................................................................................................................. 20
2.2 Connecting a Computer ..................................................................................................................... 21
2.3 Connecting Audio Devices ................................................................................................................. 21
2.4 Connecting Cameras and Video Devices........................................................................................... 22
CHAPTER 3: USING THE LED-BACKLIT DISPLAY........................................................23
3.1 Turning on the Power ......................................................................................................................... 23
3.1.1 For SC-17AH/SC-19AH/SC-22AH/SC-24AH Model................................................................ 23
3.1.2 For SC-32AH/SC-42AH Model................................................................................................ 24
3.2 Selecting the Input Source Signal ...................................................................................................... 25
3.2.1 For SC-17AH/SC-19AH/SC-22AH/SC-24AH Model................................................................ 25
3.2.2 For SC-32AH/SC-42AH Model................................................................................................ 26
3.3 Adjusting the Volume.......................................................................................................................... 27
3.3.1 For SC-17AH/SC-19AH/SC-22AH/SC-24AH Model................................................................ 27
3.3.2 For SC-32AH/SC-42AH Model................................................................................................ 28
3.4 Locking the Control Buttons ............................................................................................................... 28
3.5 Setting the Aspect Ratio..................................................................................................................... 29
3.6 Using Auto Adjustment Function ........................................................................................................ 31
CHAPTER 4: ON SCREEN DISPLAY MENU....................................................................32
4.1 Using the OSD Menu ......................................................................................................................... 32
4.2 OSD Menu Tree ................................................................................................................................. 34

3
TABLE OF CONTENTS
CHAPTER 5: ADJUSTING THE LED-BACKLIT DISPLAY...............................................36
5.1 Main Adjust......................................................................................................................................... 36
5.2 Color Adjust........................................................................................................................................ 38
5.3 Scan Settings ..................................................................................................................................... 40
5.4 Image Adjust....................................................................................................................................... 41
5.5 Information ......................................................................................................................................... 43
5.6 Language ........................................................................................................................................... 44
5.7 Setup Menu........................................................................................................................................ 44
5.8 Recall ................................................................................................................................................. 46
5.9 Exit ..................................................................................................................................................... 46
CHAPTER 6: APPENDIX...................................................................................................47
6.1 Warning Messages............................................................................................................................. 47
6.2 Troubleshooting.................................................................................................................................. 48
CHAPTER 7: SPECIFICATIONS .......................................................................................49
7.1 Display Specications ........................................................................................................................ 49
7.2 Display Dimensions............................................................................................................................ 50

SAFETY INFORMATION
4
This FCC Class-B compliant digital device complies with the Interference-Causing
Equipment Regulations of Canada.
FCC Declaimers
This device complies with Section 15 of the FCC listing. The operation procedures must meet the following
conditions: (1) the device must not cause any damaging interference; and (2) this device must accept any
received interference, including any unpredictable interference that may possibly occur.
Dear users,
This device has passed the Class B digital service regulations and complies with Section 15 of the FCC
listing; these are intended to provide reasonable warranty against damaging interference for home use. This
device will produce, use, and emit radio frequency energy; therefore, installation or use without following the
instructions given may cause damaging interference to radio communication. Nonetheless, it is not possible to
state with certainty that interference will occur from specic installations. If this device has caused damaging
interference to radio or TV signals (simply turn the device on and off to check if such interference is caused by
the device), we recommend that you x the interference using the following methods:
• Readjust the direction or location of the antenna.
• Increase the distance between this device and the receiver.
• Consult your local dealer or an experienced radio/TV technician.
Making changes or modications to the device without the permission from an authorized
dealer may void the warranty of this device.
Warning:

5
SAFETY INFORMATION
WEEE
Information for users applicable in European Union countries
The symbol on the product or its packaging signies that this product has to be
disposed separately from ordinary household wastes at its end of life. Please kindly
be aware that this is your responsibility to dispose electronic equipment at recycling
centers so as to help conserve natural resources. Each country in the European Union
should have its collection centers for electrical and electronic equipment recycling.
For information about your recycling drop off area, please contact your local related
electrical and electronic equipment waste management authority or the retailer where
you bought the product.

PRECAUTIONS
6
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Symbols used in this manual
This icon indicates the existence of a potential hazard that could result in personal injury
or damage to the product.
This icon indicates important operating and servicing information.
Notice
• Read this User Manual carefully before using the LED-backlit display and keep it for future reference.
• The product specications and other information provided in this User Manual are for reference only. All
information is subject to change without notice. Updated content can be downloaded from our web site at
http://www.agneovo.com.
• To register online, go to http://www.agneovo.com.
• To protect your rights as a consumer, do not remove any stickers from the LED-backlit display. Doing so
may affect the determination of the warranty period.
Cautions When Setting Up
Do not place the LED-backlit display near heat sources, such as a heater, exhaust vent, or in
direct sunlight.
Do not cover or block the ventilation holes in the housing.
Place the LED-backlit display on a stable area. Do not place the LED-backlit display where it
may subject to vibration or shock.
Place the LED-backlit display in a well-ventilated area.
Do not place the LED-backlit display outdoors.
Do not place the LED-backlit display in a dusty or humid environment.
Do not spill liquid or insert sharp objects into the LED-backlit display through the ventilation
holes. Doing so may cause accidental re, electric shock or damage the LED-backlit display.

7
PRECAUTIONS
Cautions When Using
Use only the power cord supplied with the LED-backlit display.
The power outlet should be installed near the LED-backlit display and be easily accessible.
If an extension cord is used with the LED-backlit display, ensure that the total current
consumption plugged into the power outlet does not exceed the ampere rating.
Do not allow anything to rest on the power cord. Do not place the LED-backlit display where the
power cord may be stepped on.
If the LED-backlit display will not be used for an indenite period of time, unplug the power cord
from the power outlet.
To disconnect the power cord, grasp and pull by the plug head. Do not tug on the cord; doing
so may cause re or electric shock.
Do not unplug or touch the power cord with wet hands.
WARNING:
Unplug the power cord from the power outlet and refer to qualied service personnel under
the following conditions:
• When the power cord is damaged.
• If the LED-backlit display has been dropped or the housing has been damaged.
• If the LED-backlit display emits smoke or a distinct odor.

8
PRECAUTIONS
Cleaning and Maintenance
Use a soft cloth to clean the glass surface and the housing.
The display can be cleaned using a cloth moistened with 95% ethyl alcohol.
Do not rub or tap the surface of the glass with sharp or abrasive items such as a pen or
screwdriver. This may result in scratching the surface of the glass.
Do not attempt to service the LED-backlit display yourself, refer to qualied service personnel.
Opening or removing the covers may expose you to dangerous voltage or other risks.
Notice for the LED-Backlit Display
In order to maintain the stable luminous performance, it is recommended to use low brightness setting.
Due to the lifespan of the lamp, it is normal that the brightness quality of the LED-backlit display may
decrease with time.
When static images are displayed for long periods of time, the image may cause an imprint on the LED-
backlit display. This is called image retention or burn-in.
To prevent image retention, do any of the following:
• Set the LED-backlit display to turn off after a few minutes of being idle.
• Use a screen saver that has moving graphics or a blank white image.
• Switch desktop backgrounds regularly.
• Adjust the LED-backlit display to low brightness settings.
• Turn off the LED-backlit display when the system is not in use.
Things to do when the LED-backlit display shows image retention:
• Turn off the LED-backlit display for extended periods of time. It can be several hours or several days.
• Use a screen saver and run it for extended periods of time.
• Use a black and white image and run it for extended periods of time.
When the LED-backlit display is moved from one room to another or there is a sudden change from low to
high ambient temperature, dew condensation may form on or inside the glass surface. When this happens,
do not turn on the LED-backlit display until the dew disappears.
Due to humid weather conditions, it is normal for mist to form inside the glass surface of the LED-backlit
display. The mist will disappear after a few days or as soon as the weather stabilizes.
There are millions of micro transistors inside the LED-backlit display. It is normal for a few transistors to be
damaged and to produce spots. This is acceptable and is not considered a failure.

9
CHAPTER 1: PRODUCT DESCRIPTION
1.1 Package Contents
When unpacking, check if the following items are included in the package. If any of them is missing or
damaged, contact your dealer.
LED-Backlit Display
Stand User Manual
Power cord VGA cable
Audio cable Remote control and
AAA batteries*
Power Mute KeyLock
Auto
VIDEO
S-VIDEO
Info
Exit
HDMI
SDI
VGA
Menu
OK
Note:
• Use only the supplied power cord.
• The above pictures are for reference only. Actual items may vary upon shipment.
• *Supplied only with the SC-32AH and SC-42AH model.

10
PRODUCT DESCRIPTION
1.2 Installation
1.2.1 Installing the Stand
1Place the LED-backlit display with the screen side down on a cushioned surface.
2Do one of the following to install the stand:
- For SC-17AH/SC-19AH and SC-22AH/SC-24AH model, align and attach the stand to the base
mount until it clicks into place.
SC-17AH/SC-19AH
SC-22AH/SC-24AH
- For SC-32AH model, align and install the stand to the base mount. Then secure the stand with the
screws.
SC-32AH
- For SC-42AH model:
a) Remove the screws from the base mount compartment.
b) Align and install the base mount to its compartment on the LED-backlit display. Then secure the
base mount with the screws.
c) Align and install the stand to the base mount. Then secure the stand with the screws.

11
PRODUCT DESCRIPTION
SC-42AH
1.2.2 Adjusting the Tilt and Rotation
For comfort viewing, you can tilt the LED-backlit display [for SC-17AH/SC-19AH/SC-22AH/SC-24AH/SC-
32AH model] to a certain degree forwards or backwards, or rotate the LED-backlit display [for SC-42AH
model] around its axis. Hold the stand with one hand and use the other hand to adjust the LED-backlit display
to the desired angle supported by your display model as described below.
-2°
20°
-2°
20°
SC-17AH (-2°~20°) SC-19AH (-2°~20°)
13.5°
-6°
-2°
13
°
SC-22AH (-6°~13.5°) SC-24AH (-2°~13°)
-4°
19°
24°
24°
SC-32AH (-4°~19°) SC-42AH (24° to the left or to the right)

12
PRODUCT DESCRIPTION
1.2.3 Removing the Stand
1Place the LED-backlit display with the screen side down on a cushioned surface.
2Do one of the following to remove the stand:
- For SC-17AH/SC-19AH model, press the release tab downwards and detach the stand from the
base mount.
Release tab
SC-17AH/SC-19AH
- For SC-22AH/SC-24AH model, pull the release lever and detach the stand from the base mount.
Release lever
SC-22AH/SC-24AH
- For SC-32AH/SC-42AH model, remove the screws from the stand, and then remove the stand.
SC-32AH
SC-42AH

13
PRODUCT DESCRIPTION
1.2.4 Wall Mounting
To wall mount the LED-backlit display, do the following steps:
1Remove the base stand. Refer to “1.2.3 Removing the Stand”.
2Place the LED-backlit display with the screen side down on a cushioned surface.
3Remove the base mount.
a. Remove the screws securing the base mount to the LED-backlit display.
b. Detach the base mount from its compartment.
SC-17AH/SC-19AH
SC-22AH/SC-24AH
SC-32AH
SC-42AH

14
PRODUCT DESCRIPTION
3Wall mount the LED-backlit display.
Screw the mounting bracket to the VESA holes at the rear of the LED-backlit display.
AC IN S-VIDEO VGA HDMI
AUDIO
OUT
AUDIO
IN
AHD/TVI/CVBS
OUT IN
100 mm
100 mm
AC IN S-VIDEO VGA HDMI
AUDIO
OUT
AUDIO
IN
AHD/TVI/CVBS
OUT IN
K
100 mm
100
mm
SC-17AH/SC-19AH SC-22AH/SC-24AH
S-VIDEOVGA HDMI
AUDIO
OUT
AUDIO
IN
AHD/TVI/CVBS
OUT IN
K
ON/OFF
AC
200 mm
10
0 mm
ON/OFF
S-VIDEOVGAHDMIAUDIO
OUT
AUDIO
IN
AHD/TVI/CVBS
IN OUT
400 mm
40
0 mm
SC-32AH SC-42AH
Note: Take measures to prevent the LED-backlit display from falling down and lessen possible injury and
damage to the display in case of earthquakes or other disasters.
• Use only the 100 x 100 mm wall mount kit recommended by AG Neovo. All
AG Neovo wall mount kits comply with VESA standard.
• Secure the LED-backlit display on a solid wall strong enough to bear its
weight.
• It is suggested to wall mount the LED-backlit display without tilting it facing
downward.

15
PRODUCT DESCRIPTION
1.3 LED-Backlit Display Overview
1.3.1 Front View and Control Buttons
SC-17AH/SC-19AH SC-22AH/SC-24AH
1
2
3
5
4
8
9
6
7
3 4 5 6 7
SC-32AH
1
2;10

16
PRODUCT DESCRIPTION
4
5
1Display screen
The LED-backlit display screen.
2Power LED indicator
• Green - Power on
• OFF - Power off
3Source
Press to select the input signal source.
4Down
• During OSD menu selection, press to move
down a menu or submenu.
Note: For SC-17AH/SC-19AH/SC-32AH
model, press to adjust the parameter
value.
• For SC-17AH/SC-19AH/SC-32AH model,
press to call out Volume Bar. Then press
again to decrease the volume.
• During source selection, press to select the
input source.
5Up
• During the OSD menu selection, press to
move up a menu or submenu.
Note: For SC-17AH/SC-19AH/SC-32AH
model, press to adjust the parameter
value.
• For SC-17AH/SC-19AH/SC-32AH model, press to
call out Volume Bar. Then press again to increase
the volume.
• During source selection, press to select the input
source.
6Menu
• Press to display the OSD menu.
• During volume adjustment, press to exit the Volume
Bar.
• During source selection, press to exit the source
menu.
7Power
Press to turn the power on or off.
8Right [for SC-22AH/SC-24AH/SC-42AH model
only]
• During OSD menu selection, press to adjust the
parameter value.
• Press to call out Volume Bar. Then press again to
increase the volume.
9Left [for SC-22AH/SC-24AH/SC-42AH model only]
• During OSD menu selection, press to adjust the
parameter value.
• Press to call out Volume Bar. Then press again to
decrease the volume.
10 Remote control sensor
Receive command signals from the remote control.
ON/OFF
S-VIDEOVGAHDMI AUDIO
OUT
AUDIO
IN
AHD/TVI/CVBS
IN OUT
SC-42AH (Rear)
SC-42AH
1 2
3
8
9
6
7
10

17
PRODUCT DESCRIPTION
5VGA connector
Use to connect a computer using a VGA cable for an
analogue input signal.
6HDMI connector
Use to connect an input device using an HDMI cable
for digital input signal.
7Main Power switch (for SC-32AH/SC-42AH model only)
Switch the main power on/off.
1.3.2 Rear View
1
AC IN S-VIDEO VGA HDMI
AUDIO
OUT
AUDIO
IN
AHD/TVI/CVBS
OUT IN
AC IN S-VIDEO VGA HDMI
AUDIO
OUT
AUDIO
IN
AHD/TVI/CVBS
OUT IN
K
K
ON/OFF
S-VIDEOVGA HDMI
AUDIO
OUT
AUDIO
IN
AHD/TVI/CVBS
OUT IN
AC
ON/OFF
S-VIDEOVGAHDMIAUDIO
OUT
AUDIO
IN
AHD/TVI/CVBS
IN OUT
S-VIDEOVGA HDMI
AUDIO
OUT
AUDIO
IN
AHD/TVI/CVBS
OUT IN
AC IN
SC-17AH/SC-19AH SC-22AH/SC-24AH
4
23567
SC-32AH
SC-42AH
1AC IN connector
Use to connect the power cord.
2AUDIO OUT / AUDIO IN connectors (2)
Use to connect an audio signal.
3AHD/TVI/CVBS OUT connectors (2)
Use to connect composite cables for CVBS
input/output signal.
4S-Video connector
Use to connect an AV cable for S-Video signal.

18
PRODUCT DESCRIPTION
1.4 Remote Control (for SC-32AH/SC-42AH model only)
1.4.1 Remote Control Buttons
Power Mute Key Lock
Auto
VIDEO
S-VIDEO
Info
Exit
HDMI
SDI
VGA
Menu
OK
1
4
2
3
5
6
7
8
9
10
11
12
13
14
8Power button
Press to turn the LED-backlit display on or off.
9Mute button
Press to mute volume.
10 Navigation buttons
Press to navigate through the OSD menu and adjust
the settings.
11 Auto button
Press to automatically adjust the image in VGA mode.
12 Video button
Press to select Video as input signal.
13 S-Video button
Press to select S-Video as the input signal.
14 Info button
Press to display the currently selected LED-backlit
display input signal.
1Key Lock button
Press to lock or unlock buttons on the control
panel or on the remote control.
2OK button
• Press to display the OSD menu.
• Press to conrm an entry or selection.
3Exit button
Press (repeatedly if necessary) to close the
OSD menu and its submenus.
4Menu button
• Press to display or hide the OSD menu.
• Press to enter or exit a submenu item.
5HDMI button
Press to select HDMI as the input signal.
6VGA button
Press to select VGA as the input signal.
7SDI button
No function.

19
PRODUCT DESCRIPTION
1.4.2 Installing the Remote Control Batteries
Two AAA-type batteries are supplied for the remote control. To install or replace the batteries, do the following:
1Remove the battery cover on the rear of the remote control.
2Insert two AAA batteries with the correct polarity (+/-) as shown inside the battery compartment.
3Replace the battery cover.
IMPORTANT!
• Avoid storing the remote control in a humid and hot environment.
• Do not place the remote control in direct sunlight.
• Do not attempt to charge, short-circuit, heat, or burn the batteries.
• If the remote control is not in use for an extended period of time, remove the batteries to prevent any
damage due to battery leakage.
• Do not mix old and new batteries or batteries of different types. Use only AAA-type batteries.
• Always follow local regulations for battery disposal.

20
CAUTION:
Make sure that the LED-backlit display is not connected to the power outlet before making any
connections. Connecting cables while the power is ON may cause possible electric shock or
personal injury.
2.1 Connecting the AC Power
1Connect the power cord to the AC power input at the rear of the LED-backlit display.
2Connect the plug to a power outlet or power supply.
AC IN
CAUTION:
When unplugging the power cord, hold the power cord by the plug head. Never pull by the cord.
CHAPTER 2: MAKING CONNECTIONS