AgSense AGSE-E237-G01 User manual

AGSE-E237-G01
(18C1601P01)
Engine Transport Stand
For General Electric Passport 20 Engine
ORIGINAL MANUAL DATED .......................................05/07/2013
LATEST MANUAL REVISION LEVEL .......................... 5/8/2023 (REV B)
Advanced Ground Systems Engineering LLC
10805 Painter Ave., Santa Fe Springs, CA, 90670 •PHONE: [phone] •FAX: [phone] •E-MAIL: [email protected]
This document contains information proprietary to
ADVANCED GROUND SYSTEMS ENGINEERING LLC
and shall not be reproduced, transferred to other documents, disclosed to others, or used for
any purpose other than that for which it is furnished without the prior written permission of
Advanced Ground Systems Engineering LLC.

AGSE-E237-G01 (18C1601P01) Passport 20 Engine Transport Stand May 9, 2023
Rev B
Notice
1. Alteration, Modification, Reengineering, or Reproduction of Equipment
The alteration, modification, reengineering, or reproduction of AGSE equipment and/or parts is
not permitted without prior written authorization from AGSE.
These modifications include but are not limited to:
• Structural changes to AGSE-supplied parts
• Substitution of AGSE-supplied parts, including hardware, with an alternate source or
supplier
• Reverse engineering of AGSE equipment and parts.
Requests for modifications should be submitted to AGSE for review – please send modification
requests to [email protected].
Once reviewed by our Engineering team, a Customer Support Letter (Subject: No Technical
Objection) will be issued for any approved modifications.
Modifications executed without prior authorization by AGSE may result in a
non-compliant product that is unsafe for operation.
Unauthorized modifications void AGSE’s and the OEM’s (Engine and/or
Airframer) approval and authority to use the product for its intended applica-
tion.
NOTE
Page A

AGSE-E237-G01 (18C1601P01) Passport 20 Engine Transport Stand May 9, 2023
Rev B
Index
SECTION DESCRIPTION PAGE(S)
1.0 Revisions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.0
2.0 Illustrations ........................................................2.0
3.0 Specification .......................................................3.0
3.1 General ........................................................3.0
3.2 Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.0
3.3 Mobility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.1
3.4 Fabrication and Finish ............................................3.1
3.5 Characteristics...................................................3.1
4.0 Maintenance and Inspection ...........................................4.0
4.1 General ........................................................4.0
4.2 Cleaning and Painting.............................................4.0
4.3 Scheduled Service................................................4.0
4.4 Scheduled Inspection .............................................4.1
4.5 General Maintenance .............................................4.2
5.0 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.0
5.1 Stand Preparation For Engine Installation .............................5.0
5.2 Engine Installation ...............................................5.6
5.3 Engine Installation onto Mount Beam ...............................5.10
5.4 Caster Operations ...............................................5.12
5.5 Stand Towings .................................................5.14
5.6 Bumper Deploying/Stowing .......................................5.15
6.0 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.0
6.1 General ........................................................6.0
6.2 Stress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.0
6.3 Prevention ......................................................6.0
6.4 Risk Assessment .................................................6.0
7.0 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.0
7.1 Statement of Warranty ............................................7.0
8.0 Parts Breakdown ....................................................8.0
8.1 General ........................................................8.0
8.2 Illustrated Parts Breakdown ........................................8.0
8.2 IPB Figure 1 - AGSE-E237-G01 Transport Stand Assembly ...........8.1
8.2 IPB Figure 2 - AGSE-E23704-S01 Cradle Assembly .................8.3
8.2 IPB Figure 3 - AGSE-E23701-S01 Base Assembly ..................8.5
8.2 IPB Figure 4 - AGSE-E23706-S01/S02 AFT Post Assembly ...........8.8
8.2 IPB Figure 5 - AGSE-E23713-S01 Adjustable AFT Brace Assembly ...8.10
Page B

AGSE-E237-G01 (18C1601P01) Passport 20 Engine Transport Stand May 9, 2023
Rev B
Index
SECTION DESCRIPTION PAGE(S)
8.2 IPB Figure 6 - AGSE-E23707-S01 AFT Bumper Assembly...........8.11
8.2 IPB Figure 7 - AGSE-E23707-S02 FWD Bumper Assembly ..........8.13
8.2 IPB Figure 8 - AGSE-E23721-S01 Sway Brace Mount Assembly ......8.15
8.2 IPB Figure 9 - AGSE-E23723-S01 Storage Box Assembly ...........8.17
9.0 Stencils, Decals, and Placards .........................................9.0
9.1 General ........................................................9.0
9.2 Stencils and Placards .............................................9.0
Page C

AGSE-E237-G01 (18C1601P01) Passport 20 Engine Transport Stand May 9, 2023
Rev B
1.0 – Revisions
The following is an itemized record of all changes from previous revision.
PAGE REV DESCRIPTION OF CHANGE DATE
A B Added Notice 5/9/2023
2.0 - 2.1 B Updated Figures 2.0-1 & 2.0-2
4.1 B Updated Section 4.4 5/9/2023
4.2 B Added Section 4.5 5/9/2023
5.14 B Updated Section 5.5 5/9/2023
5.15 B Updated Figure 5.5-1 5/9/2023
6.0 B Updated Section 6.1-6.2 5/9/2023
6.2 B Updated EC Declaration of Conformity 5/9/2023
7.0 B Updated Section 7.1 5/9/2023
8.0 B Updated Section 8.1-8.2 5/9/2023
8.1 B Added Item 6 & 7 5/9/2023
8.2 B Updated Figure 8.1-1 5/9/2023
8.3 B Updated Item 6 & 9 Part Number 5/9/2023
8.3 B Updated Item 16 Quantity 5/9/2023
8.3 B Added Item 18 & 19 5/9/2023
8.4 B Updated Figure 8.2-1 5/9/2023
8.5 - 8.6 B Updated IPB Figure 3 5/9/2023
8.7 B Updated Figure 8.3-1 5/9/2023
8.8 - 8.9 B Added IPB Figure 8.3-2 & 8.3-3 5/9/2023
8.10 B Updated Item 4 & 8 Part Number 5/9/2023
8.11 B Updated Figure 8.4-1 5/9/2023
8.12 B Updated Figure 8.6-1 5/9/2023
8.16 B Updated Figure 8.7-1 5/9/2023
8.19 B Updated Item 1 Description 5/9/2023
9.0 B Updated Figure 9.2-1 5/9/2023
9.1 B Updated Figure 9.2-2 5/9/2023
9.2 B Updated Figure 9.2-3 5/9/2023
Page 1.0

AGSE-E237-G01 (18C1601P01) Passport 20 Engine Transport Stand May 9, 2023
Rev B
2.0 Illustrations
Figure 2.0-1 AGSE-E237-G01 Transport Stand
Page 2.0

AGSE-E237-G01 (18C1601P01) Passport 20 Engine Transport Stand May 9, 2023
Rev B
2.0 Illustrations (Continued)
Figure 2.0-2 AGSE-E237-G01 Transport Stand Fully Collapsed
Page 2.1

AGSE-E237-G01 (18C1601P01) Passport 20 Engine Transport Stand May 9, 2023
Rev B
3.0 – Specification
3.1 General
The AGSE-E237-G01 Transport Stand.(Cradle/Base Assembly) is designed to store and/or trans-
port the General Electric Passport 20 full engine in modified QEC configuration. The cradle can
be separated from the base for engine storage. The engine can be installed on the stand from either
left or right side and pins into place quickly and easily.
3.2 Design
The AGSE-E23704-S01 cradle consists of a steel welded frame with removable ground handling
mounts compatible with General Electric Passport 20 engine in modified QEC configuration.
Tubular arms support engine mount adapters. Caster assemblies can be stowed to attain the
overall minimum height for air transport. Storage for unused AFT braces is provided on the
cradle frame. Storage for AFT posts, caster steering bars, tow bars is provided on the base. A
series of tie-down rings offer secure retainment during transportation of unit. Built-in shock
absorbing mounts cushion all transport shocks and vibrations. 5-1/2” x 13-1/2” fork channels are
provided to allow forklifting of the stand.
The AGSE-E23701-S01 base consists of a steel welded frame which supports the AGSE-
E23704-S01 cradle on a shock-absorbing frame. The base frame is also equipped with FWD and
AFT bumpers which can be retracted for storage.
3.3 Mobility
The AGSE-E23701-S01 base assembly has four (4) shock absorbing casters, bumpers and tow
bars. The stand cradle and base can be towed from either end. The FWD tow bars (2) attach to
the base for FWD towing and a single AFT tow bar attaches to the AFT bumper support for rear
towing. The tow bars stow on the base frame when not in use. Maximum towing speed of the unit
is 5 km/hr (3 MPH).
Failure to unlock the lead casters (tow bar end) during towing of the unit will
result in flat spots being worn into the caster tread.
If unit is to be transported by truck and trailer, it is “MANDATORY” that both
the truck and trailer be equipped with “air-ride” type suspension. The stand
must never be tied down to the truck bed above the shock mounts height.
CAUTION
CAUTION
Page 3.0

AGSE-E237-G01 (18C1601P01) Passport 20 Engine Transport Stand May 9, 2023
Rev B
3.4 Fabrication And Finish
The stand is fabricated from structural steel shapes conforming to ASTM A500, A513, and A36
materials. All bolted connections use A325 structural bolts or grade 5 commercial hardware. Unit
is primed and painted with high grade, Skydrol resistant, air dry enamel. Color is optional. Pins
and miscellaneous hardware are CRES or plated as required.
3.5 Characteristics
3.5.1 Cradle
3.5.2 Base
3.5.3 Combined Cradle/Base
Cradle
Length (In.) 94.5
Height (In.) 60
Width (In.) 92.5
Weight (Lbs.) 1,201
Base
Length with tow bars stowed (In.) 131.25
Length with tow bars deployed (In.) 266.5
Width (In.) 88
Height (In.) 53-5/16
Weight (Lbs.) 2,318
Combined Cradle/Base
Length with tow bars stowed (In.) 131.25
Length with tow bars deployed (In.) 266.5
Width (In.) 92.5
Height (In.) 85.5
Weight (Lbs.) 3,556
Page 3.1

AGSE-E237-G01 (18C1601P01) Passport 20 Engine Transport Stand May 9, 2023
Rev B
4.0 – Maintenance and Inspection
4.1 General
Life expectancy of this unit can be extended indefinitely, if it is properly maintained. By design,
there is only minimal periodic servicing required. Annual inspections for damage, weld cracks, or
corrosion are recommended. Prior to each use, the stand should be inspected for obvious signs of
abuse or shipping damage. Observed damage should require complete inspection of the affected
area to ensure stand integrity is not compromised.
4.2 Cleaning and Painting
The stand should be cleaned with a soap and water solution and rinsed thoroughly.
Re-lubricate all grease zerk fittings after cleaning stand.
Damaged paint should be touched-up with paint provided by AGSE or other Skydrol resistant
high-grade enamel paint. Superficial scratches are expected during normal usage and will not
affect function.
4.3 Scheduled Service
All casters should be lubricated every 90 days with the following extreme pressure grease or
equivalent grease:
Visual inspection of the swivel locks and brakes should occur with the scheduled lubrication. All
non-painted machined surfaces should have a light grade oil spray as required. Spray with aerosol
lubrication WD-40 or equivalent.
WARNING
Manufacturer Product
Mobil Oil Company Mobilplex E.P. #1
Texaco Oil Company Texaco E.P. #1
Gulf Oil Corporation Gulf Crown E.P. #1
Shell Oil Company Shell Alavania E.P. #1
Page 4.0

AGSE-E237-G01 (18C1601P01) Passport 20 Engine Transport Stand May 9, 2023
Rev B
Page 4.1
4.4 Scheduled Inspection
Prior to each use, this equipment should be inspected for obvious signs
of abuse or shipping damage. Observed damage should require com-
plete inspection of the affected area to ensure structural integrity is not
compromised.
Annual inspections of machined surfaces, pins, fasteners, structure and shock mounts are recom-
mended. The machined surfaces (wheels, axles, pivots) are to be visually inspected for signs of wear
or corrosion. Action is to be taken immediately if areas are determined to be potentially dangerous to
operating personnel, or a detriment to the equipment. Pins and fasteners are to be visually inspected
for cracks, damage, or corrosion. Loose fasteners should be tightened. The structure is to be visually
inspected for damage, weld cracks, or corrosion.
CAUTION
CAUTION
AGSE recommends that shock mounts be replaced every five (5) years.
Additionally, periodic inspections should be performed and any of the fol-
lowing conditions are proper cause for replacement of the shock mounts
prior to their expiration:
1. Visible evidence of cracks.
2. Discoloration: visible damage caused by solvents.
3. Permanent deformation.
4. Mount does not flex during engine loading/unloading.
5. Significant corrosion on shock attach-plate.
The following exposures can reduce the life of shock mounts and it is recommended to avoid them
where possible.
• High humidity and/or salty air
• Direct sunlight
• Solvent, corrosive liquids, and fumes
• Oils, jet fuel, or Skydrol hydraulic fluid
• Extreme temperatures
• Ozone or engine exhaust

AGSE-E237-G01 (18C1601P01) Passport 20 Engine Transport Stand May 9, 2023
Rev B
4.5 General Maintenance Schedule
NOTE:
This Maintenance Schedule does not supersede the maintenance described by Customers’
Company Maintenance Policy. Intervals indicated are recommendations only and should be
altered to take into consideration usage factors and environmental conditions.
1* - Inspection for missing parts before every use.
2* - Carry out function test if equipment has not been used for extended period of time.
3* - AGSE recommends that shock mounts be replaced within five (5) years of the date marked on
shock mounts.
4* - Check that manual is present before every use.
5* - Latest manuals are available from www.agsecorp.com or call [phone]
Legend
I - Inspect/Check
T - Tighten
L - Lubricate
H - Spray with rust inhibitor
R - Replace
Recommended Lubricant: Chevron Dura-Lith Grease EP, NLGI2 or equivalent.
Component Task to be Performed Maintenance Intervals
Monthly 3 Months 6 Months Yearly
General Inspect for missing parts 1*
Inspect paint/plating finish I
Inspect exposed/bare metal for rust H
Function check equipment 2*
Inspect all stencils/placards/stamps I
Casters Check wheel condition I
Tighten mounting bolts T
Check swivel lock/brake I
Lubricate bearings L
Structure Inspect frame for damage/cracked welds I
Tighten all bolts T
Lubricate/protect moving joints H L
Pins Inspect for damaged/bent/worn pins I
Inspect for broken/cracked pin handles I
Inspect for broken/cut lanyards I
Shock
Mounts
Check date 3*
Inspect rubber for cracking/deformation I
Inspect for permanent set/deformation I
Manual Check manual is present/readable 4*
Check manual revision is current 5*
Page 4.2

AGSE-E237-G01 (18C1601P01) Passport 20 Engine Transport Stand May 9, 2023
Rev B
5.0 - Operation
5.1 Stand Preparation For Engine Installation
NOTE: The transport stand is assumed to be in the fully collapsed configuration.
1) Inspect stand for obvious damage.
2) Raise the stand off the ground using a forklift or an overhead hoisting system.
3) Deploy the four (4) casters by removing four (4) AM-91000-82T safety pins (IPB Figure
3 - Item 17). Secure with the same hardware. (Illustration Figure 5.1-1).
4) Lower the stand to the ground then set the caster brakes.
REMOVE
AM-91000-82T SAFETY PIN
ROTATE CASTER DOWN
SECURE WITH REMOVED
SAFETY PIN
(4 PLACES)
5) Remove the AGSE-E23706-S01 LH AFT post assembly and AGSE-E23706-S02 RH AFT
post assembly (IPB Figure 2 - Items 2 and 3 respectively) from their storage on the base by
removing four (4) AGSE-E23706-P03 clevis pivot pins (IPB Figure 2 - Item 4) and the hold-
down pin.
6) Install the LH and RH AFT post assemblies on the cradle and secure with the hardware
removed in Step 5. (Illustration Figure 5.1-2).
Figure 5.1-1
Page 5.0

AGSE-E237-G01 (18C1601P01) Passport 20 Engine Transport Stand May 9, 2023
Rev B
REMOVE
AGSE-E23706-P03 PIVOT PIN (4)
TO REMOVE
AGSE-E23706-S01 LH AFT POST ASSY
AGSE-E23706-S02 RH AFT POST ASSY
INSTALL
AGSE-E23706-S02
RH AFT POST ASSY
ON CRADLE
INSTALL
AGSE-E23706-S01
LH AFT POST ASSY
ON CRADLE
Figure 5.1-2
7) Remove four (4) AM-91000-34T safety pins (IPB Figure 2 - Item 13) to remove the two
(2) AGSE-E23713-S01 adjustable AFT brace assemblies (IPB Figure 2 - Item 5) from their
storage.
8) Attach the adjustable brace assemblies, one end to the AFT post assemblies, the other to the
cradle. Secure with the hardware removed in Step 7.
9) Remove AGSE-E23721-S01 sway brace mount (IPB Figure 2 - Item 8) from storage by
removing AM-91000-66T safety pin (IPB Figure 8 - Item 6). Install the sway brace mount
on the cradle as indicated in Illustration Figure 5.1-3.
Page 5.1

AGSE-E237-G01 (18C1601P01) Passport 20 Engine Transport Stand May 9, 2023
Rev B
10) Remove AGSE-E23720-P01 cylinder jack (IPB Figure 2 - Item 16) from storage by remov-
ing two (2) AM-90500-16T safety pins (IPB Figure - Item 9). Determine which is the cor-
rect post, move AGSE-E23719-P01 cylinder mount (IPB Figure 2 - Item 7) to that post and
attach with AM-90500-72T (IPB Figure 2 - Item 10) safety pin. Attach the cylinder jack to
the cylinder mount and post using the removed hardware. (Illustration Figure 5.1-4).
11) Remove four (4) AM-90750-48T safety pins (IPB Figure 3 - Item 15) to extend the FWD
and AFT bumpers (IPB Figure 3 - Items 5 and 4) from their storage positions. Extend the
bumpers as needed for engine configuration. Secure with the same hardware.
REMOVE
AM-91000-34T SAFETY PIN (4)
TO REMOVE
AGSE-E23713-S01 AFT BRACE ASSY (2)
FROM STORAGE
REMOVE
AM-91000-66T SAFETY PIN
TO REMOVE
AGSE-E23721-S01
SWAY BRACE MOUNT
INSTALL
AGSE-E23721-S01
SWAY BRACE MOUNT
INSTALL
AGSE-E23713-S01
AFT BRACE ASSEMBLY
(2 PLACES)
Figure 5.1-3
Page 5.2

AGSE-E237-G01 (18C1601P01) Passport 20 Engine Transport Stand May 9, 2023
Rev B
REMOVE AM-90500-20T SAFETY PIN (2) TO REMOVE AGSE-E23720-P01 CYLINDER JACK FROM STORAGE
INSTALL AGSE-E23720-P01 CYLINDER JACK
REMOVE AM-90750-48T SAFETY PIN (2) TO EXTEND AGSE-E23707-S02 FWD BUMPER
REMOVE AM-90750-48T SAFETY PIN (2) TO EXTEND AGSE-E23707-S01 AFT BUMPER
INSTALL AGSE-E23720-P01 CYLINDER JACK
REMOVE AM-90500-20T SAFETY PIN (2) TO REMOVE AGSE-E23720-P01 CYLINDER JACK FROM STORAGE
Figure 5.1-4
Page 5.3

AGSE-E237-G01 (18C1601P01) Passport 20 Engine Transport Stand May 9, 2023
Rev B
12) Remove two (2) AM-90750-48T and two (2) AM-90750-68T safety pins and rotate the
FWD bumper into the upright position. Secure with the same hardware. Remove two (2)
AM-90750-68T safety pins and rotate the AFT bumper into the upright position.
Leave the FWD bumper in the flat condition when the testing bellmouth
is installed on the engine.
NOTE
REMOVE
AM-90750-68T SAFETY PIN (2)
TO ROTATE THE AGSE-E23707-P03
FWD BUMPER SUPPORT ARM
INTO THE UPRIGHT POSITION
(2 PLACES)
REMOVE
AM-90750-48T SAFETY PIN
TO ROTATE THE AGSE-E23715-P01
FWD BUMPER INTO THE UPRIGHT POSITION
REMOVE
AM-90750-48T SAFETY PIN
TO ROTATE THE AGSE-E23715-P03
AFT BUMPER INTO THE UPRIGHT POSITION
Figure 5.1-5
Page 5.4

AGSE-E237-G01 (18C1601P01) Passport 20 Engine Transport Stand May 9, 2023
Rev B
13) Remove AM-90250-32L safety pin (IPB Figure 3 - Item 13) to remove the two (2)
AM-2228-D9 caster steering bars (IPB Figure 3 - Item 11) from their storage positions.
REMOVE AM-90250-32L SAFETY PIN TO REMOVE AM-2228-D9 CASTER STEERING BAR (2) FROM STORAGE
Figure 5.1-6
Page 5.5

AGSE-E237-G01 (18C1601P01) Passport 20 Engine Transport Stand May 9, 2023
Rev B
5.2 Engine Installation (Figures 5.2-1 and 5.2-3)
NOTE: The stand is assumed to be in the ready configuration as described in Section 5.1.
1) Inspect stand for obvious damage.
2) Configure engine for shipping in accordance with General Electric Engine Shipping Manual.
3) Set the caster brakes.
4) If the engine is to be installed from the LH side of the stand, remove the LH adjustable AFT
brace by removing two (2) AM-91000-34T safety pins. Put the brace and hardware aside or
store on the cradle frame.
5) Pull the 3 AM-90750-48T safety pins from each of the AFT post assemblies and rotate the
AGSE-E23710-S01 & -S02 link assemblies to the upright stowed position and re-pin in place.
6) Remove the AM-91500-88T (IPB Figure 2 - Item 15) safety pin to pivot the AGSE-
E23706-S01 LH AFT post to the rear until it is horizontal. This will require two men, an
overhead crane or the use of the manual cylinder AGSE-E23720-P01.
7) Remove the FWD mount supports, AGSE-E23714-P01, and attach them to the LH & RH
FWD brackets of the 189C1617G01 bracket set. Secure with AM-91000-41TNC safety pins.
8) Using an overhead hoisting system, lower the engine onto the stand from the LH side of the
stand. Use the FWD mount supports to guide the engine into the stand and the FWD mount
dork pins into their sockets in the cradle. Secure with AM-90750-80T Safety Pins.
Minimal clearance exists between the engine and stand. The operator is
responsible to ensure the engine does not contact the stand. This may
require the removal or adjustment of engine components.
Care must be taken when working near suspended loads. Personnel
should never stand beneath the suspended load.
9) Make necessary adjustments to align the upper RH AFT bracket of the 18C1619G02 bracket
set with the AGSE-E23706-S02 RH AFT post’s AGSE-E23710-S02 adjustable link assy (IPB
Figure 4 - Item 4). Secure with the AM-91000-32T safety pin (IPB Figure 4 - Item 9).
10) Make necessary adjustments to the AGSE-E23721-S01 sway brace mount (IPB Figure 2 Item
8) to align the engine’s lower RH AFT bracket with the AGSE-E23721-P02 sway bar (IPB
Figure 8 - Item 2). Secure with the AM-90750-T20 safety pin (IPB Figure 8 - Item 3).
11) Pivot the AGSE-E23706-S01 LH AFT post assembly (IPB Figure 2 - Item 2) to the upright
position AND PIN IN PLACE. Make necessary adjustments to the LH AFT post’s AGSE-
E23710-S01 adjustable link assembly (IPB Figure 4 - Item 3) to align with the engine upper
LH bracket. Secure with the AM-91000-32T safety pin (IPB Figure 4 - Item 9).
12) Install the LH adjustable brace and secure with safety pins
CAUTION
WARNING
Page 5.6

AGSE-E237-G01 (18C1601P01) Passport 20 Engine Transport Stand May 9, 2023
Rev B
REMOVE AM-91000-34T SAFETY PIN (2) TO UNINSTALL AND STORE THE AGSE-E23713-S02 ADJUSTABLE LH AFT BRACE
REMOVE AM-91000-34T SAFETY PIN TO PIVOT THE AGSE-E23706-S01 LH AFT POST TO HORIZONTAL POSITION
RAISE AGSE-E23710-P01 UPPER LINK TO UPRIGHT STOWED POSITION AND PIN IN PLACE
REMOVE AM-90500-20L SAFETY PIN TO REMOVE AGSE-E23720-P01 LIFTING CYLINDER
REMOVE AM-90500-72T SAFETY PIN TO REMOVE AGSE-E23719-P01 CYLINDER MOUNT
Figure 5.2-1
Page 5.7