Aguilar AG 500SC User manual

AG 500SC
Owners Manual
Manual Version 1.7
1.

Table of Contents
I. Getting Started page 3.
A. Safety Instructions
B. Manual Conventions
C. Basic Setup
D. Protection Modes
II. Features and Functions page 5.
A. Front Panel
B. Rear Panel
C. Cabinet
III. Warranty Information page 7.
2.

I. Getting Started
A. Safety Instructions
Please follow these guidelines:
A) Vents are provided for heat dissipation at the rear of the
amplifier. Maintain at least a 1” space around these vents to
provide sufficient ventilation. If you decide to rack mount the
amplifier make sure you do not block the vents.
B) Keep all sources of fire, such as lighted candles, away from the
amplifier.
C) This product is approved for use in any climate.
D) Do not expose the product to dripping or splashing. Do not
place objects filled with fluid on the amplifier.
E) Amplifier must be connected to a mains socket outlet with a
protective earthing connection.
F) The appliance coupler (AC cord) is the disconnect device. The
disconnect device shall remain readily operable at all times.
B. Manual Conventions
In this manual, words that appear in italics represent actual physical
controls on the AG 500SC.
C. Basic Setup
Plug in your instrument. The amount of power this amplifier will produce
varies with the impedance rating of your cabinets.
One 8 ohm cabinet – 250 watts
Two 8 ohm cabinets – 500 watts
One 4 ohm cabinet – 500 watts
With the
Master volumes down, turn on your amplifier. Adjust as follows:
3.

Preamp:
1. Turn the Gain up while playing. Turn up until the Clip
light flashes and then back off until the light stops flashing. You have
now optimized your signal to noise ratio.
2. If you have a particularly high output instrument it may be necessary to
push the
–10dB button in to prevent clipping of the input buffer. This
button is located next to the
Input jack and when pushed in it lowers your
input signal by 10dB.
3. Turn up the
Master control until you reach the volume you need.
D. Protection Modes
Overcurrent Mode:
In this mode the preamp remains active, but the power amp mutes. The
Status light does not flash. Power cycle the amp to reset. This may
happen if the load is too low, or if you plug and unplug cabinets while
playing.
Thermal/DC Mode:
In this mode both the preamp and the power amp mute. The
Status light
flashes. Power cycle the amp to reset. This may happen if the AC line
power is not correct, if the amp is overheating, or if there is risk of
damage to the amp or speakers.
4.

II. Features and Functions
A. Front Panel Features
Input Pad:
-10dB
Preamp Section:
Bright : +5dB >4kHz shelving
Treble : +/- 13dB @ 4kHz shelving
High Mid : +/- 14dB @ 800Hz peaking
Low Mid : +/- 14dB @ 400Hz peaking
Bass : +/- 18dB @ 40Hz shelving
Deep : +6dB <100Hz shelving
Effects Loop Section:
Send :Output level = -infinity to +22dBu
Adjust the level of the Send output to get the maximum
performance from your effects unit.
Return : Sensitivity = -20dBu to +infinity
(This range of signals can be adjusted to get the nominal output
level at the speaker output.) Adjust this knob to optimize the signal
level returning from the Effects Loop. If it is turned up too high,
you can clip the return circuitry of the AG 500. If it is turned down
too low you might not be able to get loud enough.
Pull –20dB :Boosts the level of the Return signal by 8dB.
This allows you to use a studio effects unit (line level) or a stomp
box (instrument level) in the Effects Loop. If the signal returning
from the Effects Loop is too quiet, pull this knob to boost the
Return signal.
5.

Pull Series : Removes any “dry” (un-effected) signal from the
signal path.
When this knob is pushed in the Effects Loop is configured in
“parallel” and you can mix your “dry” signal with the signal from
the Effects Loop. When this knob is pulled out the Effects Loop is
configured in “series” and all of your signal will pass through the
Effects Loop. If you do not have anything plugged into the Effects
Loop pulling this knob will cut off your signal completely.
D.I. Section:
D.I. Nominal Output Level: -20dBu
D.I.
Pre/Post Button:
Pre - Your signal goes to the D.I. XLR output jack before
your
Gain and EQ settings, but after the
–10dB input pad.
Post - Gain , EQ, Master settings and effects will be sent to
the D.I. XLR output jack.
Lift/Ground :If there is a hum when using the D.I. there may be
a ground loop. In many cases pushing in the
Lift/Ground button
can fix this problem.
* Note: The AG 500SC will not be harmed by phantom power
through the D.I. Phantom power is a power supply that can be
switched on at the channel input of some mixing consoles. It is
used to power some types of microphones. Use of phantom power
(usually labeled as 48V) will have no effect on the D.I. or the
amplifier in general.
B. Rear Panel Features
Speaker Outputs: Two Speakon outputs and two ¼” outputs are
provided. Any combination may be used as long as the load does not
exceed 4 ohms.
Tuner Output: One ¼” Tuner output is provided. When the amplifier is
muted your signal will still reach the tuner.
6.

7.
III. Warranty Information
Please send in your Warranty Registration card or register online upon receipt of
your amplifier. Your original receipt is also necessary for warranty repairs. The
AG 500SC has a 3 year limited warranty against manufacturing defects. If you
experience a problem with your amplifier, please contact
[e-mail] to receive a Return Authorization number or for
information on the nearest authorized repair center.