AI AI-SSR User manual

AI-SSR
Sirius Satellite
Radio Receiver
Avionics Innovations, Inc.
2450 Montecito Road. Ramona, CA 92065
[phone] - [phone] Fax
Installation Manual
9000B Rev NC December 13th 2002

Avionics Innovations
AI-SSR Installation Manual
Table of Contents
Title Page
Table of Contents------------------------------------------------------------------------- 1
General Information---------------------------------------------------------------------- 2
Specifications------------------------------------------------------------------------------ 3
Warranty Information-------------------------------------------------------------------- 4
Warranty Registration-------------------------------------------------------------------- 5
Installation Instructions------------------------------------------------------------------ 6
Installation Schematic-------------------------------------------------------------------- 7
Revision NC 11/27/2002
Page 1

Avionics Innovations
AI-SSR Installation Manual
General Information
The purpose of this AI-SSR Installation Manual is to provide information to ensure proper
installation and operation of this product.
This product has been tested and is “FAA-PMA” approved. It is the responsibility of those
installing this item on or within a specific type or class of certified aircraft to document and
obtain approval for an acceptable installation from the Federal Aviation Administration or other
governing authority.
Unpacking and Inspection of AI-SSR
Exercise extreme care when unpacking the AI-SSR. Make a visual inspection of the unit for
evidence of damage incurred during shipment. If a claim for damage is to be made, unit must be
returned in the original packaging.
Revision NC 11/27/2002
Page 2

Avionics Innovations
AI-SSR Installation Manual
SPECIFICATIONS
Digital Radio Section
Receiving Frequencies: 2322.293/2330.207 MHz
Audio
Signal to Noise Ratio: 95dB
Distortion: 0.01 % (1kHz)
General
Power Supply Voltage: 12-30 Volts DC
Ground: Negative
Current Draw: 1 Amp
Weight: 2 lbs
Deminsions: 8” x 6.25” x 1.5”
Antenna
Weight: 5 Ounce
Height: .73 Inch
Diameter: 3.50 Inches
Finish: Skydrol Resistant Polyurethane Enamel
Material: ALUM 6061-T6, Thermoset Plastic
Connector: Type “TNC” Female
Revision NC 11/27/2002
Page 3

Avionics Innovations
AI-SSR Installation Manual
WARRANTY INFORMATION
Avionics Innovations warrants the AI-SSR Player against material or manufacturing defects for a period of one year from
the date of installation.
Avionics Innovations will, upon receipt of the failed unit, repair or replace the unit at our discretion. Avionics Innovations
will pay UPS Ground shipping charges for warrantied items. Charges for express shipment will be the responsibility of the
sender.
This warranty will be void if the unit has been tampered with or opened by unauthorized personnel.
To validate warranty:
1.) Return the enclosed warranty registration form to Avionics Innovations or complete the online Warranty Application at
www.avionicsinnovations.com
This warranty is not transferable . Any implied warranties expire at the expiration date of this warranty. WE SHALL
NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. This warranty does not cover a defect
that has resulted from improper or unreasonable use or maintenance as determined by us. This warranty is void if there is
any attempt to disassemble this product without factory authorization. During the warranty period , the unit must be
returned to Avionics Innovations and, at own option, will be repaired or replaced at no charge. IMPORTANT: Any labor
charges associated with the removal of product or related trouble shooting by any firm other than Avionics Innovations
will not be covered.
Revision NC 11/27/2002
Page 4

Avionics Innovations
AI-SSR Installation Manual
WARRANTY REGISTRATION FORM
Model ______________ S/N _____________________________________________________
Date of install __________________________________________________________________
Owners name and address_________________________________________________________
______________________________________________________________________________
______________________________________________________________________________
Aircraft make and model__________________________________________________________
______________________________________________________________________________
Registration number _____________________________________________________________
Installing agency________________________________________________________________
______________________________________________________________________________
Comments : ____________________________________________________________________
______________________________________________________________________________
Revision NC 11/27/2002
Page 5

Avionics Innovations
AI-SSR Installation Manual
INSTALLATION INSTRUCTIONS
NOTE
FOR TECHNICAL ASSISTANCE PLEASE CALL 760-788-2602 8:00 AM TO 5:00 PM PST.
ALL REPAIRS AND RETURNS ARE PROCESSED THROUGH AVIONICS INNOVATIONS
NOTE
This unit requires a subscription service from Sirius Satellite Radio. The service can be obtained by
contacting Sirius Satellite Radio @ 1-888-539-7474 or on the web www.sirius.com Information
needed to start subscription will be aircraft make and model, owners address, credit card
information for monthly billing and the Sirius ID # located on the back panel of the AI-SSR unit.
1. Select an appropriate location in the instrument panel for the AI-SSR tray.
A. Location should be as near to center to maximize viewing quality.
2. Mount tray in location using (6) 6/32 countersunk screws. Screws must mount flush to the
inside of the tray for clearence.
3. Wire the unit as per attached diagram.
4. Install antenna on top of aircraft using approved practices and
data. Ensure the antenna is well bonded Resistance between antenna and mating surface to be
less than 10mΩ.
5. Use RG 142 for antenna lead.
INSTALLATION NOTES:
1. The Antenna will need a clear view of the Northern Sky for proper reception. The AI-SSR will not
operate inside the hangar, and in some instances next to tall hangars that ubstruct the view of the
Satellite to the Antenna
2. Consult the intercom manufacturer for specifications and hookup instructions.
3. Unit must be completely seated in tray to ensure proper connection.
4. Do not over tighten the unit into the tray. Over tightening can damage unit.
POST INSTALLATION CHECKOUT
1. Ensure unit operates according to the AI-SSR operations manual 9000A
Revision NC 11/27/2002
Page 6