aii-do light KF-6188 User manual

1/9
KF-6188
DMX MOVING HEAD
USER MANUAL

2/9
Congratulations on purchasing this KF- 6188
Thank you for extending your trust in our technology!
For reasons of safety and approval (CE) the personal reconstruction and/or modification of
this product is prohibited. Please observe that damage caused by modifications performed
manually to this device is not covered by the warranty.
This product leaves our works in a perfect condition. Please observe all notes in these
operating instructions to warrant this condition and the safe operation of the product!
Any damage caused as a result of the non-compliance with these operating instructions
leads to the expiration of any warranty claim. The manufacturer does not accept liability for
any damage to property or for personal injury resulting from the improper handling of the
product, or non-observance of the operating instructions.
Store these operating instructions in a safe place for later reference and pass them to any
new holder when selling or lending or leaving this device in the hands of any other party.
Application According to Purpose
This product is a lighting effect which creates special light effects with one lamp. To generate
these effects, the product must be connected to mains and a DMX-512 compatible controller.
This product is designed for 230V, 50Hz A/C operation and exclusively for indoor use.
If used for any purpose other than described in these operating instructions, the device may
suffer damage and the warranty expires. Also, any other use is linked with risks such as
short circuits, fire, electrical shock, etc.
The manufacturer's serial number must never be removed as otherwise the warranty
expires.
Notes on Safety
1. Before Operation
ATTENTION:
DANGER OF LIFE! RISK OF FIRE!
RISK OF SHORT CIRCUIT!
Prior to the initial operation of this product, please do the followings
- Read these operating instructions with great care;
- Study and observe all instructions carefully;
- Ensure that everybody and anybody involved in the installation, operation, transport and
storage of this product is suitably qualified;
- Verify whether any visible damage was caused during transport. If the power cord,
housing or the light are damaged, do not operate the device; contact your specialized
dealer immediately.
2. Supply Voltage, Mains Cord and Connection to Mains
ATTENTION:
DANGER OF LIFE!
RISK OF FIRE! RISK OF SHORT CIRCUIT!
The handling of supply voltage, mains cords and connections to mains calls for particular
care considering the risk from a life-threatening electric shock, the risk of fire and the risk of
short circuits! Please observe the following notes in particular:
Products operating on supply voltage should be kept out of the reach of children. Therefore
ensure the permanent supervision if children are in the immediate vicinity of the product!

3/9
For commercial facilities the regulations on the prevention of accidents of the respective
trade association must be observed. The operation of this equipment at schools, training
facilities, and hobby or self-help workshops must be supervised responsibly by trained
personnel.
Check the product regularly for any damage to the mains cord! Should you discover any
damage to the mains cord, do not operate or disconnect this product! Secure the product
against accidental operation and contact your specialized dealer!
Always separate the product from mains by holding the mains plug by the handling surface.
Never disconnect by holding the line cord! Be sure to connect the product exclusively to 230
V, 50 Hz A/C!
Always ensure during installation, operation, transport and when storing the product that the
mains cord is not exposed to possible mechanical damage, or damage caused by humidity,
fluids, heat or cold!
The product's cable entry must not be exposed to stress from pull! Create the mains
connection once the product has been installed only. Always connect the mains plug last!
The product must only be connected to a proper outlet of the public supply grid. Connect the
mains cord to suitable outlets only! Use extensions cords in compliance with specifications
only! Do not allow the mains cord to come into contact with other cords!
Ensure during installation, operation, transport and storage that none of the cables are freely
exposed! Never touch the mains cord, mains plug and outlets with wet or damp hands!
When not using the product, and prior to cleaning always disconnect the product from mains!
To do so, hold the mains plug by the handling surface and never pull the mains cord!
Never connect the device to dimmer packs!
3. Housing
ATTENTION:
DANGER OF LIFE! RISK OF BURNS!
RISK OF FIRE! RISK OF SHORT CIRCUIT!
Always ensure during installation, operation, transport and when storing the product that no
shocks or other forces impact the housing!
The housing must not touch onto any other devices or objects during operation!
Easily flammable materials, e.g. decoration material and other surfaces and objects, must
maintain a minimum distance of 3m to the housing! Walls must maintain a minimum distance
of 50cm to the housing! The device must be installed on a fireproof surface only (no carpet)!
Always ensure a proper circulation of air.
Do not touch the housing during operation - it will heat up. The housing is safe to touch
approx. 5 minutes following the end of operation!
The device must never be carried via the projector arms. Use the carrying handles only!
Fluids must not enter the housing as this could reduce the protective insulation and may
trigger short circuits which may lead to fatal electric shocks! If fluids have entered,
disconnect the mains plug immediately and secure the product against unintentional
operation and contact your specialized dealer! Damage caused as a result of fluids entering
the housing is exempt from warranty.
No metal parts or other items must enter the housing as this may reduce the protective
insulation or trigger short circuits which may lead to fatal electric shocks! If metal parts or
other items have entered, disconnect the mains plug immediately, secure the product against
unintentional operation and contact your specialized dealer! Damage caused by metal parts

4/9
or other items in the housing is exempt from warranty.
4. Operating Environment
ATTENTION:
DANGER OF LIFE! RISK OF BURNS!
RISK OF FIRE! RISK OF SHORT CIRCUIT!
The product must be operated and stored in a dry environment only! Splash water, rain,
humidity, fog may reduce the protective insulation which may lead to fatal electric shocks!
The limit value for relative humidity is 50% at 45°C. A minimum distance of 1.5m to a fog
machine must be observed; fog saturation in the room must not reduce the visibility to below
10m.
The product must be operated at a temperature range of between -5 °C and 45 °C only.
Protect the product against direct exposure to sunlight or other heat, such as from radiators!
If the product is taken from a cold environment into a warm environment it must only be
taken into operation once it has reached ambient temperature, since the condensation
created by the difference in temperature may destroy the device!
Protect the product against dust! Dust may reduce the protective insulation, which may
cause fatal electric shocks!
The product must be operated at altitudes ranging between 20m below and 3000m above
sea level only!
The product must not be operated during thunder storms; risk of destruction from surge
voltages!
The product must be operated at a minimum distance of 1.5 m to lit objects only!
5. Installation
ATTENTION:
DANGER OF LIFE!
This product can be operated suspended or as a stand-alone system.
Should your lighting effect show any signs of damage, do not install the device! In this case,
have your lighting effect repaired by your specialized dealer. The manufacturer does not
accept responsibility or liability for damage to property or personal injury resulting from an
improperly installation!
As a stand-alone system the device must be installed vertically on an absolute planar, firm,
fireproof, shock- and vibration-free surface. The installation of this lighting effect must be
carried out by trained and professional staff! The installation of this lighting must only be
carried out with the appropriate materials!
The suspended installation of this lighting effect necessitates a suitable suspension system!
The lighting effect must never be fixed swinging freely in the room. No individuals should
linger underneath the lighting effect during suspended installation!
It is a must to install this device with a second independent fixture. Such second fixture must
guarantee in the event of failure of the main fixture that no assembly parts will fall down. Use
the fixture on the undersurface only.
The light effect unit must be attached via two certified hooks and omega bracket to a tie-bar
system. Use the screw threads on the undersurface only.
It must be ensured that an expert inspects the mechanical and safety-relevant installation

prior to the initial operation and following major modifications, prior to the renewed operation.
It must be ensured that an expert inspects the mechanical and safety-relevant installation at
least once a year. It must be ensured that an expert inspects the mechanical installation and
the installation of relevance to safety within the framework of an acceptance test at least
every four years.
The installation fixture must be as such that it can withstand for a period of 60 minutes 10
times the load capacity without harmful deformation.
It is prohibited for any individual to unnecessarily stay or pass beneath the installation during
any type of assembly work.
The light effect unit must be secured by a safety arrester cable if fly-mounted. The cable
must withstand 12 times the weight of the light effect unit. Use arrester cables equipped with
quick closing links. The dropping distance must not exceed 20 cm. Defect arrester cables or
arrester cables that have already been exposed to stress must not be used.
6. Operation
ATTENTION:
RISK OF HEALTH!
Controls
Link all DMX devices with a DMX-512 controller by using a standard, 3-pin DMX cable.
Connect the output of the first device with the input of the second device and the output of
the second device with the input of the third device and so on.
Connect the mains plug to an outlet.
Operating the product for the first time may generate smoke and odour; this is not a defect.
Avoid dis/connecting the product repeatedly and quickly from/with mains! Always wait 15
minutes prior to the next dis/connection!
The device starts not until a self-testing and starting time. If the moving head is ready to start,
push and roll the function wheel. The LCD display shows the options, as below:
6.1. Menu settings:
1. Version: brand, model, version, number, lamp time, use time
2. Address: set address
3. Pan direction: On (reversed) Off (normal)
4. Tilt direction: On (reversed) Off (normal)
5. Pan/Tilt speed: from 00-15, to set the speed for Pan/Tilt movement
6. Pan/Tilt mode: 8bit, 16bit, when set as 8bit, the channels Pan fine and Tilt fine will be
disabled, the fixture has 12 channels now.
7. lamp mode: On (lamp on); Off (lamp off)
8. Reset: lighting reset; time restore (can be set password afterwards to prevent unwanted
modifying); Motor restore (can be set password afterwards to prevent unwanted
modifying); exit.
9. Channel data: 01:pan; 02:tilt; 03:pan fine; 04:Tilt fine; 05:pan/tilt speed; 06:reset;
07:Color; 08:gobo; 09:gobo rotate;10:focus; 11: prism; 12:prism rotation; 13:strober;
14:dimmer; 15-16:---;17: exit.
5/9

6/9
10. Display: language(English Chinese or some other language according to your
requirement ); Backlight time: open(always on ); 30 seconds. Back-brightness:1-5, from
dark to bright; exit.
11. Motor adjust: 01:pan; 02:tilt;03:color wheel; 04:rotating gobo wheel; 05:gobo rotation; 06:
focus;07:prism; 08:prism rotation;09:strobe;10:motor zero;11:save (can be set password
afterwards to prevent unwanted modifying). 12: exit.
12. Control: Control (DMX, Auto, music, slave ); Run (01-09,select the program you want to
run in certain mode); speed (01-15,set running speed for program).
13. Help info: include copyright, company information, etc.
14. Exit
6.2 DMX PROTOCOL
：
Channel Function DMX
value Feature Note
1 Pan 0-255 0-540°pan movement
2 Tilt 0-255 0-280°tilt movement
3 Pan fine 0-255 16 bit pan movement
4 Tilt fine 0-255 16 bit tilt movement
5 Pan, tilt Speed 0-255 Pan/Tilt speed adjustment from fast
to slow
0-143 No function
144-151 Shutter off when pan and tilt
movement
152-159 Shutter off when changing color
160-167 Shutter off when changing gobo
168-175 Shutter off when pan and tilt
movement and color changing
176-183 Shutter off when pan and tilt
movement and gobo changing
184-191 Shutter off when changing color or
gobo
192-199 Shutter off when pan and tilt
movement and color gobo
changing
200-207 Lamp off after 3s
208-215 Lamp on after 3s
216-239 No function
240-247 Reset
6 Shutter off，lamp
on/off, reset
248-255 No function

7/9
0-7 White
8-15 Color 1
16-23 Color 2
24-31 Color 3
32-39 Color 4
40-47 Color 5
48-55 Color 6
56-63 Color 7
64-191 !*7 color mixing
192-223 Color wheel CCW rotation from
slow to fast, rainbow effect
7 Color wheel
224-255 Color wheel CW rotation from slow
to fast, rainbow effect
0-7 White
8-15 Gobo 1
16-23 Gobo 2
24-31 Gobo 3
32-39 Gobo 4
40-47 Gobo 5
48-55 Gobo 6
56-63 Gobo 7
64-79 Gobo7 shaking from slow to fast
80-95 Gobo6 shaking from slow to fast
96-111 Gobo5 shaking from slow to fast
112-127 Gobo4 shaking from slow to fast
128-143 Gobo3 shaking from slow to fast
144-159 Gobo2 shaking from slow to fast
160-175 Gobo1 shaking from slow to fast
176-191 White shaking from slow to fast
8 Gobo
192-255 Gobo wheel CW flowing with
increasing speed
0-159 Forwards gobo rotation with your
pushing of fader
160-191 Gobo shaking, increasing in
amplitude and speed
9 Gobo rotation
192-223 Backwards gobo rotation with
decreasing speed

224-255 Forwards gobo rotation with
decreasing speed
10 Focus 0-255 Focus adjustment from far to near
0-7 No function
8-63 Prism
11 Prism and gobo
macros effect 64-255 Prism and gobo macros effect
0-159 Prism rotation with your pushing of
fader
160-191 Prism shaking , increasing in
amplitude and speed
192-223 Backwards prism rotation with
decreasing speed
12 Prism rotation
and amplitude
adjustment
224-255 Forwards prism rotation with
decreasing speed
0-15 No function
16-47 Full on
48-95 Strobe from slow to fast
96-143 Pulse effect ,opening, increasing
144-191 Pulse effect ,closing, increasing
192-239 Random strobe
13
Strobe
240-255 Full on
14 Dimmer 0-255 Dimming from 0-100%
7. Lamps
ATTENTION:
DANGER OF LIFE! RISK OF BURNS!
RISK OF FIRE!
During operation, the lamps will reach temperatures of up to 600°C. Touching the lamps may
cause serious burns! Objects coming into contact with the lamps during and shortly after
operation may catch fire!
Disconnect the product from mains prior to installing or before changing a lamp! Allow a lamp
to cool for approx. 15 minutes before exchanging it!
Never touch a lamp with bare hands! If damaged or deformed, a lamp must be exchanged!
When exchanging the lamp be sure to use suitable lamps only. Lamps with greater
performance generate excessive heat for the product; risk of fire! Damage resulting from the
use of an unsuitable lamp is exempt from warranty!
Never connect the lighting effect to the mains prior with opened housing.
8. Fuse
8/9

ATTENTION:
DANGER OF LIFE!
Disconnect the product from the mains prior before changing a fuse.
Only replace the fuse by a fuse of same type and rating! An incorrect fuse could damage or
destruct the lighting effect.
Replace a fuse by levering the fuse holder cover with an appropriate screwdriver. Remove
the old fuse and place the fuse inside the holder. Replace the fuse holder and insert it.
Never connect the lighting effect to the mains prior with opened housing.
9. Cleaning
ATTENTION:
DANGER OF LIFE! RISK OF FIRE!
RISK OF SHORT CIRCUIT!
The product must be freed regularly from dust, other deposits and contamination as this may
reduce the protective insulation, which may lead to a fatal electric shock!
Before cleaning, always disconnect the product from mains!
This product should be cleaned with a moist cloth only; never use aggressive cleaning
agents, solvents or benzine for cleaning.
Ensure that the product is completely dry before operating it again after cleaning!
10. Transport
CAUTION:
FRAGILE!
To avoid damage caused during transport, wrap the product in its original packaging only
and handle it with great care during transport!
Technical Information
Voltage: 220 V AC, 50 Hz
Lamp: HMI 680W
Fuse: F 7 A 250 V
Color wheel: 7 colours + rainbow effect + white
Gobo wheel: 7 gobos + blank
Pan/Tilt: 540°/ 280°
Dimensions: 505 x 485 x 590 mm
Weight: 26 kg
Please note: All information is subject to change without prior notice.
9/9