Ledj Slimline 12HEX12 User manual

Order codes: LEDJ84
Slimline 12HEX12
12 x 12W six-colour LEDs
(RGBAWUV)
User Manual
Optional
IR remote
Order ref:
LEDJ90F

www.prolight.co.uk Slimline 12HEX12 User Manual 2
Safety advice
WARNING
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL
CAREFULLY BEFORE YOUR INITIAL START-UP!
• Beforeyourinitialstart-up,pleasemakesurethatthereisnodamagecausedduringtransportation.
• Shouldtherebeanydamage,consultyourdealeranddonotusetheequipment.
• Tomaintaintheequipmentingoodworkingconditionandtoensuresafeoperation,itisnecessary
fortheusertofollowthesafetyinstructionsandwarningnoteswritteninthismanual.
• Pleasenotethatdamagescausedbyusermodicationstothisequipmentarenotsubjecttowarranty.
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused by the non-observance
of this manual or any unauthorised modication to the equipment.
OPERATING DETERMINATIONS
Ifthisequipmentisoperatedinanyotherway,thanthosedescribedinthismanual,theproductmaysufferdamageand
thewarrantybecomesvoid.Incorrectoperationmayleadtodangere.g:short-circuit,burnsandelectricshocksetc.
Donotendangeryourownsafetyandthesafetyofothers!
Incorrectinstallationorusecancauseseriousdamagetopeopleand/orproperty.
• Neverletthepowercablecomeintocontactwithother
cables.Handlethepowercableandallmainsvoltage
connectionswithparticularcaution!
• Neverremovewarningorinformativelabelsfromtheunit.
• Donotopentheequipmentanddonotmodifytheunit.
• Donotconnectthisequipmenttoadimmerpack.
• Donotswitchtheequipmentonandoffinshortintervals,
asthiswillreducethesystem’slife.
• Onlyusetheequipmentindoors.
• Donotexposetoammablesources,liquidsorgases.
• Alwaysdisconnectthepowerfromthemainswhen
equipmentisnotinuseorbeforecleaning!Onlyhandle
thepower-cablebytheplug.Neverpullouttheplugby
pullingthepower-cable.
• Makesurethattheavailablevoltageisbetween
100~240V,50/60Hz.
• Makesurethatthepowercableisnevercrimpedor
damaged.Checktheequipmentandthepowercable
periodically.
• Iftheequipmentisdroppedordamaged,disconnectthe
mainspowersupplyimmediatelyandhaveaqualied
engineerinspecttheequipmentbeforeoperatingagain.
• Iftheequipmenthasbeenexposedtodrastic
temperatureuctuation(e.g.aftertransportation),
donotconnectpowerorswitchitonimmediately.
Thearisingcondensationmightdamagetheequipment.
Leavetheequipmentswitchedoffuntilithasreached
roomtemperature.
• Ifyourproductfailstofunctioncorrectly,stopuse
immediately.Packtheunitsecurely(preferablyinthe
originalpackingmaterial),andreturnittoyourProLight
dealerforservice.
• Onlyusefusesofsametypeandrating.
• Repairs,servicingandpowerconnectionmustonlybe
carriedoutbyaqualiedtechnician.THISUNITCONTAINS
NOUSERSERVICEABLEPARTS.
• WARRANTY:Oneyearfromdateofpurchase.
CAUTION!
KEEP THIS EQUIPMENT
AWAY FROM RAIN,
MOISTURE AND LIQUIDS
CAUTION!
TAKE CARE USING
THIS EQUIPMENT!
HIGH VOLTAGE-RISK
OF ELECTRIC SHOCK!!

www.prolight.co.uk Slimline 12HEX12 User Manual 3
Product overview & technical specications
Housing12x12Wsix-colourLEDs,theSlimline12HEX12givessmoothcolourmixingfromrichsaturatedhues
tosubtlepastelshades.Theseunitshavearugged,allmetalhousingandmeasureonly115mmindepthfor
easytransportationandinstallation.The4pushbuttonLEDmenuorsuppliedIRremotealloweasyaccessto
thefunctionsincludingDMX,master/slaveandsoundactive.
•12x12Wsix-colourLEDs(RGBWAUV)
•Beamangle:35°(eldangle:65°)
•1.2kHzrefreshrate
•DMXchannels:2/3/3/4/4/5/6or9selectable
•Staticcolour,colourchange,colourfade,autorun,
soundactiveandmaster/slavemodes
•0-100%dimmingandvariablestrobe
•Bracketallowsformultipleriggingoroorstanding
applications
•Rubberfeetallowthepanelto
sitatontheoorforuplighting
•4pushbuttonmenuwithLEDdisplay
•SideentryXLRandpowerconnections
•IECpowerinput/output
•3-PinXLRinput/output
•Fancooled
•OptionalIRremote(LEDJ90F)
Slimline 12HEX12
Specications Slimline 12HEX12
Powerconsumption 144W
Powersupply 100~240V,50/60Hz
Fuse T1A250V
Dimensions 280x248x120mm
Weight 3.8kg
Ordercode LEDJ84
0m 1m 2m 3m 4m 5m
35° - Lux 10430 2720 1296
35°
723 464
248mm 115mm
284mm

www.prolight.co.uk Slimline 12HEX12 User Manual 4
Technical specications
01-Bracket
02-Brackettighteningknobs
03-Functionbuttons
04-LEDdisplay
05-FuseT1A250V
06-Earthpoint
07-IECpowerinput
08-IECpoweroutput
09-3-PinDMXoutput
10-3-PinDMXinput Inthebox:1 x xture,
1 x power cable &
1 x user manual
05 06 08 09 10
POWER SUPPLY: 100-240V~50/60Hz
FUSE: T1A, 250V
POWER OUT DMX OUT DMX IN
ENTER DOWN
MODE
UP
www.prolight.co.uk
SLIMLINE 12HEX12
02
04
03
01
07
PUSH

www.prolight.co.uk Slimline 12HEX12 User Manual 5
Operating instructions
DMX channel mode:
OperatinginaDMXcontrolmodeenvironmentgivestheuserthegreatestexibilitywhenitcomesto
customisingorcreatingashow.Inthismodeyouwillbeabletocontroleachindividualtraitofthexture
andeachxtureindependently.
ToaccesstheDMXchannelmode,pressthe“MODE”buttonontherearoftheunittoshow-CH
ontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstosetthe
desiredDMXaddress.Nowpressthe“ENTER”buttontochooseoneofthe2,3,3,4,4,5,6or9DMX
channelmodes.Usethe“UP”and“DOWN”buttons,andpressthe“ENTER”buttontoconrmthesetting.
Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
Channel Value Function
1000-255 Masterdimmer(0-100%)
2
000-255colourmacro
000-016 Red
017-033 Green
034-050 Blue
051-067 White
068-084 Amber
085-101 UV
102-118 Yellow(R-255,G-200,A-255)
119-135 Cyan(G-255,B-255)
136-152 Lavender(R-170,B-210)
153-169 Brightgreen(G-255,A-180)
170-186 Magenta(R-255,B-90,UV-255)
187-203 Turquoise(G-255,B-180,UV-255)
204-220 Orange(R-200,A-200)
221-237 Coolwhite(R-70,G-190,B-255,A-200)
238-255 Warmwhite(R-230,G-255,B-255,A-255,W-255)
2 channel mode:

www.prolight.co.uk Slimline 12HEX12 User Manual 6
Operating instructions
Channel Value Function
1000-255 Red(0-100%)
2000-255 Green(0-100%)
3000-255 Blue(0-100%)
Channel Value Function
1000-255 Masterdimmer(0-100%)
2000-255 Flash(speed0-100%,1Hz-20Hz)
3000-004 Blackout
005-010 Red
011-015 Green
016-020 Blue
021-025 White
026-030 Amber
031-035 UV
036-040 Yellow(R-255,G-200,A-255)
041-045 Cyan(G-255,B-255)
046-050 Lavender(R-170,B-210)
051-055 Brightgreen(G-255,A-180)
056-060 Magenta(R-255,B-90,UV-255)
061-065 Turquoise(G-255,B-180,UV-255)
066-070 Orange(R-200,A-200)
071-075 Coolwhite(R-70,G-190,B-255,A-200)
076-080 Warmwhite(R-230,G-255,B-255,A-255,W-255)
081-150 Colourchangespeed
Slowest(081)changesevery8secs
Fastest(150)changesevery0.3secs
151-220 Colourfadespeed
Slowest(151)changesevery8secs
Fastest(220)changesevery0.3secs
221-255 Soundcontrol(micsensitivity)
3 channel mode 1:
3 channel mode 2:
Channel Value Function
1000-255 Red(0-100%)
2000-255 Green(0-100%)
3000-255 Blue(0-100%)
4000-255 White(0-100%)
Channel Value Function
1000-255 Red(0-100%)
2000-255 Green(0-100%)
3000-255 Blue(0-100%)
4000-255 Amber(0-100%)
Channel Value Function
1000-255 Red(0-100%)
2000-255 Green(0-100%)
3000-255 Blue(0-100%)
4000-255 White(0-100%)
5 000-255 Amber(0-100%)
Channel Value Function
1000-255 Red(0-100%)
2000-255 Green(0-100%)
3000-255 Blue(0-100%)
4000-255 White(0-100%)
5 000-255 Amber(0-100%)
6 000-255 UV(0-100%)
4 channel mode 1: 4 channel mode 2:
5 channel mode: 6 channel mode:

www.prolight.co.uk Slimline 12HEX12 User Manual 7
Operating instructions
Channel Value Function
1000-255 Masterdimmer(0-100%)
2000-255 Flash(speed0-100%,1Hz-20Hz)
3000-255 Red(0-100%)
4000-255 Green(0-100%)
5 000-255 Blue(0-100%)
6 000-255 White(0-100%)
7000-255 Amber(0-100%)
8000-255 UV(0-100%)
9 000-004 Blackout
005-010 Red
011-015 Green
016-020 Blue
021-025 White
026-030 Amber
031-035 UV
036-040 Yellow(R-255,G-200,A-255)
041-045 Cyan(G-255,B-255)
046-050 Lavender(R-170,B-210)
051-055 Brightgreen(G-255,A-180)
056-060 Magenta(R-255,B-90,UV-255)
061-065 Turquoise(G-255,B-180,UV-255)
066-070 Orange(R-200,A-200)
071-075 Coolwhite(R-70,G-190,B-255,A-200)
076-080 Warmwhite(R-230,G-255,B-255,A-255,W-255)
081-150 Colourchangespeed
Slowest(081)changesevery8secs
Fastest(150)changesevery0.3secs
151-220 Colourfadespeed
Slowest(151)changesevery8secs
Fastest(220)changesevery0.3secs
221-255 Soundcontrol(micsensitivity)
9 channel mode:

www.prolight.co.uk Slimline 12HEX12 User Manual 8
RGBAWUV colour mix mode:
Inthismodeyoucansetthexturetoanycolourandanybrightness.
Toaccessthecolourmixmode,pressthe“MODE”buttonontherearoftheunittoshow C1--
with3digitsafterontheLEDdisplay.Pressthe“ENTER”buttontoconrm.
TheC1representsred,C2=green,C3=blue,C4=white,C5=amber,C6=UVandCF0=strobe.
The2digitsafterarethebrightnesssettingfrom 00~99,orthestrobespeedifinCF0.
For example:
Ifyouset1,2,3,4,5and6alltozero,yourunitwillhavenoLEDslitup(blackout).
IfyousetC100toC199and2,3,4,5and6tozero,yourunitwillshowonlyredLEDs.
Pressthe“ENTER”buttontoconrmthesettingandmovetothenextcolour.
Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
Colour fade mode:
Toaccessthecolourfademodepress“ENTER”untilthedisplayshowsFA--ontheLEDdisplay.
Toadjustthespeedusethe“UP”and“DOWN”buttonstoselectanyvaluefromFA00~FA99.
Toselectthestrobemodepress“ENTER”,theLEDdisplaywillchangetoFF--,usingthe“UP”and
“DOWN”buttonstoselectanyvaluefromFF00~FF99.
Value: 00 - 99 (00 = low, 99 = high)
Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
Colour change mode:
Toaccessthecolourchangemodepress“ENTER”untilJU--showsontheLEDdisplay.Toadjust
thespeedusethe“UP”and“DOWN”buttonstoselectanyvaluefromJA00~JA99.Toselectthe
strobemodepress“ENTER”,thedisplaywillchangetoJF--,usingthe“UP”and“DOWN”buttons
toselectanyvaluefromJF00~JF99.
Value: 00 - 99 (00 = low, 99 = high)
Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
Master/slave mode:
Tosetthemasterunit,pressthe“MODE”buttonontherearofthemasterunitthenselectyour
desiredprogram(soundactive,auto,staticcolour,colourmixoroneofthebuilt-inprograms).
Tosettheotherunitsinslavemode,pressthe“MODE”buttonontherearoftheunittoshowSLAU
ontheLEDdisplayandpressthe“ENTER”buttontoconrmthesetting.Theunitswillnowrunin
sequencewiththemasterunit.
Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
PleaseensurethatallslaveunitsaresettothesameDMXchannelmodeasthemasterunit.
Operating instructions

www.prolight.co.uk Slimline 12HEX12 User Manual 9
Sound active mode:
Toaccessthesoundactivemode,pressthe“MODE”buttonontherearoftheunittoshowSU00
ontheLEDdisplay.Nowpressthe“ENTER”buttonandusethe“UP”and“DOWN”buttonstosetthe
soundsensitivitylevelfromSU.00~SU.99andpressthe“ENTER”buttontoconrmthesetting.
Value: 00 - 99 (00 = low, 99 = high)
Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
Auto run mode:
Toaccesstheautorunmode,pressthe“MODE”buttontoshowAUtOontheLEDdisplay.
Thexturewillthenautomaticallyscrollthroughcolourfadeandcolourchange.Thespeed/ashrate
isnotadjustable.
Pressthe“ENTER”buttontoconrmthesetting.
Toexitoutofanyoftheaboveoptions,pressthe“MODE”button.
Colour preset mode:
Toaccessthecolourpresetmode
press“ENTER”untilCn--shows
ontheLEDdisplay.Toadjustthe
colourusethe“UP”and“DOWN”
buttonstoselectanyvalue
fromCn01~Cn15.
Pressthe“ENTER”buttonto
conrmthesetting.
Toexitoutofanyoftheabove
options,pressthe“MODE”button.
Operating instructions
Staticcolourmode C1.00~C1.99R
C2.00~C2.99G
C3.00~C3.99B
C4.00~C4.99W
C5.00~C5.99A
C6.00~C6.99U
CF.00~CF.99Flash
Colourmacromode
Cn01-15
Cn01-Red
Cn02-Green
Cn03-Blue
Cn04-White
Cn05-Amber
Cn06-UV
Cn07-Yellow
Cn08-Lightblue
Cn09-Pink
Cn10-Lightgreen
Cn11-Rosepink
Cn12-Peacockblue
Cn13-Orange
Cn14-Pastelblue/white
Cn15-White
Colourchangingmode JU00~JU99(speed)
JF00~JF99(ash)
Colourfademode FA00~FA99(speed)
FF00~FF99(ash)
Automode AUTO
Slavemode SLAV
Soundactivemode SU00~SU99
DMXmode 2CH,3CH1,3CH2,4CH1,4CH2,5CH,
6CH,9CH
Addresssetting A001~A512
Menusystem

www.prolight.co.uk Slimline 12HEX12 User Manual 10
Operating instructions
Optional IR remote functions:
Button functions:
DMX address examples:
Important notes:
• SettheDMXaddressoneachxturebeforepluggingintotheDMXcontroller
• TheIRremoteiscannotbeusedwhenthexture(s)arebeingcontrolledwithaDMXcontroller
• ThemaximumIRtransmitterdistanceis10m-PleasemakesurethatyouhavetheIRremoteaimed
directlyatthefrontpanelofeachxturetobeprogrammed
• Ifyoudonotpressthe“DMXMODE”buttonafteryouhavechangedtheDMXaddresswhenyou
powerdownthextureitwilllosetheaddressyouhaveset
01-Setsthecxtureintopoweronoroffmodes
02-Setsinautorun
03-Runsthebuilt-inprograms,usethe‘+’and‘-’
buttonstogothroughtheprograms
04-SetstheLEDstoashonandoff,usethe‘+’
and‘-’buttonstochangetheashfrequency
05-Setstherunspeed,usethe‘+’and‘-’buttons
tochangethedesiredspeed(note:onlyavailablein
thecolourchangeorcolourfademodes)
06-SetsthextureintoDMXmode
07-Setsthextureintosoundactivemode
08-Setsthextureintoslavemode
09-SetstheDMXaddressforthexture
10-SetstheLEDscolour,usethe‘+’and‘-’
buttonstochangethebrightness
1 2 3
4 5 6 0
+
_
7 8 9
AR
D
FL
SL
SP
S
S PR
SA
RG B
WAUV
BLACKOUT DIMMING
FLASH
SLAVE
SPEED
SET ADDR
SELECT PROG
SOUND ACTIVE
AUTO RUN
DMX MODE
03
01
04
10
02 05
07 08
06 09
TosettheDMXaddress“245”;
• Pressthe“S”button,theredLEDswillcomeon,
youcannowstarttosettheDMXaddress
• Nowpressthe“2”button,thegreenLEDswill
comeon,thismeanstherstdigithasbeen
setat2
• Nowpressthe“4”button,theblueLEDswill
comeon,thismeanstheseconddigithasbeen
setat4
• Nowpressthe“5”button,andallofthe
R,G,B,A,WandUVLEDswillcomeon,
thethirddigit5hasbeenset.ThefullDMX
addresssettinghasbeenchanged
• Nowpressthe“DMXMODE”buttontosave
thenewaddressintothememory
TosettheDMXaddress“002”;
• Pressthe“S”button,theredLEDswillcomeon,
youcannowstarttosettheDMXaddress
• Nowpressthe“0”button,thegreenLEDswill
comeon,thismeanstherstdigithasbeen
setat0
• Nowpressthe“0”button,theblueLEDswill
comeon,thismeanstheseconddigithasbeen
setat0
• Nowpressthe“2”button,andallofthe
R,G,B,A,WandUVLEDswillcomeon,
thethirddigit2hasbeenset.ThefullDMX
addresssettinghasbeenchanged
• Nowpressthe“DMXMODE”buttontosave
thenewaddressintomemory
Optional
IR remote
Order code:
LEDJ90F

www.prolight.co.uk Slimline 12HEX12 User Manual 11
Setting the DMX address:
TheDMXmodeenablestheuseofauniversalDMXcontroller.Eachxturerequiresa“startaddress”
from1-512.Axturerequiringoneormorechannelsforcontrolbeginstoreadthedataonthechannel
indicatedbythestartaddress.Forexample,axturethatoccupiesoruses7channelsofDMXandwas
addressedtostartonDMXchannel100,wouldreaddatafromchannels:100,101,102,103,104,105
and106.Chooseastartaddresssothatthechannelsuseddonotoverlap.E.g.thenextunitinthe
chainstartsat107.
DMX 512:
DMX(DigitalMultiplex)isauniversalprotocolusedasaformofcommunicationbetweenintelligent
xturesandcontrollers.ADMXcontrollersendsDMXdatainstructionsformthecontrollertothexture.
DMXdataissentasserialdatathattravelsfromxturetoxtureviatheDATA“IN”andDATA“OUT”
XLRterminalslocatedonallDMXxtures(mostcontrollersonlyhaveadata“out”terminal).
DMX linking:
DMXisalanguageallowingallmakesandmodelsofdifferentmanufacturestobelinkedtogether
andoperatefromasinglecontroller,aslongasallxturesandthecontrollerareDMXcompliant.
ToensureproperDMXdatatransmission,whenusingseveralDMXxturestrytousetheshortest
cablepathpossible.TheorderinwhichxturesareconnectedinaDMXlinedoesnotinuencethe
DMXaddressing.Forexample;axtureassignedtoaDMXaddressof1maybeplacedanywherein
aDMXline,atthebeginning,attheend,oranywhereinthemiddle.Whenaxtureisassigneda
DMXaddressof1,theDMXcontrollerknowstosendDATAassignedtoaddress1tothatunit,
nomatterwhereitislocatedintheDMXchain.
DATA cable (DMX cable) requirements (for DMX operation):
ThisxturecanbecontrolledviaDMX-512protocol.TheDMXaddressissetonthebackoftheunit.
YourunitandyourDMXcontrollerrequireastandard3-pinXLRconnectorfordatainput/output,
seeimagebelow.
Also remember that DMX cable must be daisy chained and cannot be split.
DMX setup
FurtherDMXcablescanbe
purchasedfromallgoodsound
andlightingsuppliersor
ProLightConceptsdealers.
Pleasequote:
CABL10 – 2m
CABL11 – 5m
CABL12 – 10m

www.prolight.co.uk Slimline 12HEX12 User Manual 12
Notice:
Besuretofollowthediagramsbelowwhenmakingyourowncables.Donotconnectthecables
shieldconductortothegroundlugorallowtheshieldconductortocomeincontactwiththeXLRs
outercasing.Groundingtheshieldcouldcauseashortcircuitanderraticbehaviour.
Special note:
Line termination:
Whenlongerrunsofcableareused,
youmayneedtouseaterminatoron
thelastunittoavoiderraticbehaviour.
Using a cable terminator will decrease
the possibilities of erratic behaviour.
(3-pin - Order ref: CABL9O, 5-pin - Order ref: CABL89)
5-pin XLR DMX connectors:
Somemanufacturesuse5-pinXLRconnectorsfordatatransmissioninplaceof3-pin.5-pinXLRxtures
maybeimplementedina3-pinXLRDMXline.Wheninsertingstandard5-pinXLRconnectorsintoa
3-pinlineacableadaptormustbeused.Thediagrambelowdetailsthecorrectcableconversion.
Terminationreducessignaltransmission
problemsandinterference.itisalways
advisabletoconnectaDMXterminal,
(resistance120Ohm1/4W)betweenpin2
(DMX-)andpin3(DMX+)ofthelastxture.
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
3-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
5-pin XLR (socket)
Pin 1: GND (screen)
Pin 2: Signal (-)
Pin 3: Signal (+)
Pin 4: N/C
Pin 5: N/C
DMX setup

www.prolight.co.uk Slimline 12HEX12 User Manual 13
WEEE notice
Correct Disposal of this Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries
with separate collection systems)
Thismarkingshownontheproductoritsliterature,indicatesthatitshouldnotbedisposedof
withotherhouseholdwastesattheendofitsworkinglife.Topreventpossibleharmtothe
environmentorhumanhealthfromuncontrolledwastedisposal,pleaseseparatethisfromother
typesofwastesandrecycleitresponsiblytopromotethesustainablereuseofmaterialresources.
Householdusersshouldcontacteithertheretailerwheretheypurchasedthisproduct,ortheir
localgovernmentofce,fordetailsofwhereandhowtheycantakethisitemforenvironmentally
saferecycling.
Businessusersshouldcontacttheirsupplierandcheckthetermsandconditionsofthe
purchasecontract.Thisproductshouldnotbemixedwithothercommercialwastesfordisposal.

www.prolight.co.uk Slimline 12HEX12 User Manual 14

www.prolight.co.uk Slimline 12HEX12 User Manual 15

www.prolight.co.uk Slimline 12HEX12 User Manual 16