Air King AKTN-107BK User manual

42”(107cm) Tower Fan with Remote Control
Instruction Manual
For Model AKTN-107BK
WARNING To reduce the risk for fire, electric shock or personal injury
•Do not use this fan with any solid-state speed control device.
•Unplug the fan before cleaning or servicing.
•If you disassemble your fan, completely re-assemble before plugging into outlet.
•To reduce the risk of electric shock and injury to persons, do not use in window.
PLEASE READ AND SAVE THESE IMPORTANT INSTRUCTIONS
This fan is for residential use only. It is not intended for use in commercial or industrial
settings.

Important instructions
Read and save these important safety instructions
before using this fan, when using electrical
appliances, basic safety precautions should always
be followed including the following:
WARNING - To reduce the risk of fire or electrical
shock, do not use this product with any solid-state
speed control device. To reduce the risk of fire or
electric shock and injury to persons, do not use in a
window.
-Use this fan only as described in this manual.
Other uses not recommended may cause fire or
electric shock.
-This product is intended for HOUSEHOLD USE
ONLY and not for commercial, industrial or
outside use. To protect against electrical shock,
do not place fan in window, immerse unit, plug or
cord in water, or spray with liquids.
-Unplug the fan from the outlet when not in use,
when moving fan from one location to another
and before cleaning.
-Do not operate the fan in the presence of
explosive and/or flammable fumes.
-Do not place the fan or any parts near an open
flame, cooking or other heating appliance.
-Avoid contact with moving fan parts.
-To disconnect, grip the plug and pull it from the
wall outlet. Never yank the cord.
-The use of attachments is not recommended and
may cause hazards.
-Always use on a dry, level surface.
-Do not operate if the fan housing is removed or
damaged.
-Do not operate any fan with a damaged cord or
plug.
-Discard fan or return to an authorized service
facility for examination and/or repair.
-Do not run cord under carpeting. Do not cover
cord with throw rugs, runners, or similar
coverings. Do not route cord under furniture or
appliances.
-Arrange cord away from traffic area and where it
will not be tripped over.
-The appliance is not to be used by persons
(including children) with reduced physical,
sensory or mental capabilities, or lack of
experience and knowledge, unless they have
been given supervision or instruction.
-Children being supervised not to play with the
appliance.
-This appliance can be used by children aged
from 8 years and above and persons with
reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they have
been given supervision or instruction concerning
use of the appliance in a safe way and
understand the hazards involved.
-Children shall not play with the appliance.
-Cleaning and user maintenance shall not be
made by children without supervision.
Assembly
1. Pass the cord through the base. Assemble the
two base halves together. Position the base half
with the alignment pin, over the other base half
with the alignment sockets. Press the two
halves together until flush.
2. Assemble the base to the tower bottom. With
the tower on its side, align the 4 base sockets
onto the tower bottom pins. Tighten the thumb
screws securely.
How to operate
1. This Fan may be operated by the Manual
Controls located on top of the unit or by the
Remote Control.
2. Place the Fan on a firm and level surface.
3. Plug the cord set into the outlet.

Power (A) The fan functions ON and OFF by
pressing the power button. Lights on the fan’s
control panel indicate the power is ON.
Fan Speed (B) The fan speed can be adjusted by
pressing the SPEED button. Press the button to
switch between the speed settings.
Timer (C) The fan has an automatic timer to turn the
unit OFF at intervals of 1,2,4 or 8 hours. To set the
timer, turn the unit on at the required speed, press
the timer button until the desired run time is
illuminated. The fan will turn off once the time has
expired.
Oscillation (D) The oscillation feature can be
activated by pressing the Oscillation button. The fan
can be set to a stationary position by pressing the
button again.
Remote control
1. Install batteries. The battery is size “CR2025”
2. All the functions performed with the Remote-
Control work identically to the Manual Controls.
3. Do not mix old and new batteries. Do not mix
alkaline, standard (carbon-zinc) or rechargeable
(nickel- cadmium) batteries.
4. DO NOT DISPOSE OF BATTERIES IN FIRE.
BATTERIES MAY EXPLODE OR LEAK.
Cleaning
•Be sure your fan is in the OFF position.
•Unplug the fan before cleaning.
•To clean inlet and outlet ribs, use a common
household vacuum.
•Do not use water to clean these parts of the Fan.
•Do not disassemble for cleaning.
•Do not immerse the fan in water and never allow
water to enter the Motor Housing.
•Do not use gasoline, paint thinner or other
chemicals to clean the fan.
Storage Instructions
For storage, you may leave the fan assembled and
covered to protect it from dust. Store the fan in a
cool, dry place.
TROUBLE SHOOTING TIPS
If your Fan fails to operate, see below for a probable
cause and solution.
•Be sure the power cord is plugged into a working
electrical outlet.
If you have a problem that cannot be resolved by the
step listed above, please return the fan to the place
of the original purchase or see your warranty. Do not
attempt to open the motor housing yourself; doing so
may void your warranty and cause damage to the
fan or personal injury.

Description of parts
1. Remote control
2. Carry handle
3. Rear grill
4. Front grill
5. Rear base
6. Front base
Technical Specifications
Model: AKTN-107BK
Power Supply: 220-240V~ 50Hz
Rated Power: 55W
Class II
Conforms to all relevant European Directives.
Maximum fan flow
rate
F
28.07
m3/min
Fan Power input
P
49.9
W
Service Value
SV
0.56
(m3/min)
/W
Standby power
consumption
PSB
0.30
W
Fan sound power
level
LWA
60.5
dB(A)
Maximum air
velocity
c
2.68
m/sec
Measurement standard for service value
Commission Regulation (EU) No 206/2012
IEC 60879:1986, EN 50564:2011
EN 60704-2-7:1998, EN 60704-1:2010