AirBedz XUV Series User manual

OWNER’S MANUAL
PLEASE GO TO
WWW.PITTMANOUTDOORS.COM
FOR PRODUCT WARRANTY REGISTRATION
IT IS HIGHLY RECOMMENDED THAT YOU READ AND FOLLOW
THE INFORMATION CONTAINED IN THIS MANUAL BEFORE
INITIAL SET UP.
WARNING:
DO NOT LEAVE INFLATED WHEN NOT IN USE. OVER-INFLATION
WILL OCCUR WHEN EXPOSED TO DIRECT SUNLIGHT.
INCLUDES RECHARGEABLE BATTERY
Please follow charging instructions on page 2.
PPI-CMO_XUV
PPI-TAN_XUV
PPI-BLU_XUV
XUV Series
NOTES

WARNING: THIS PRODUCT IS NOT FLAME RESISTANT. THIS BED CONTAINS PLASTIC. DO NOT
PLACE AIR BED NEAR OPEN FLAME OR OTHER SOURCE OF IGNITION.
WARNING: This is not a toy. To avoid risk of fire, burns, injury or shock, it should not be played
with or placed where small children can reach it.
NOTE: This product contains a nickel metal hydride battery and must be fully charged on a
monthly basis. Do not dispose of air pump and battery in fire. Check your local regulations for
proper disposal instructions.
• Unplug adapter when not in use.
• Pump is an electrical device. Do not use in or around water.
• Do not attempt to disassemble, repair, or service the pump. No serviceable parts are
contained inside. Contact Pittman Outdoors at
WARNING:
• This is not a water toy or flotation device. Use as a bed only.
• Not recommended for use by children under three (3) years of age.
• This bed is not intended for infants or persons with limited mobility. They may roll off of the bed
and become entrapped between the bed and the sides of the truck bed or walls and suffocate.
• Do not use this bed on abrasive surfaces or near pointed, sharp or protruding objects. Bed may
puncture. Remove all sharp objects from area the bed will be used in.
• Do not step or jump on bed or use as a trampoline. Standing, jumping or walking on the bed
may result in injury and/or damage or puncture the bed.
• Make sure truck bed is clean of any debris, sharp objects or protrusions or place bed in a safe
area before use making sure that there are no sharp edges, steps, drops, or breakable items
nearby. Use on flat surfaces only. Bed may tip over on uneven surfaces.
• Do not inflate or use mattress while vehicle is in motion.
CHARGING PUMP
DO NOT CHARGE THE BATTERY PACK FOR MORE THAN 2 HOURS WHEN USING THE DC CHARGER
(Car Charger)! **** Available as an additional accessory - Part No. PPI-AC4* ***
1. CHARGE BATTERY PACK (D) BEFORE USE. Remove battery pack from pump housing.
Charge battery pack for 10 hours prior to initial use using the included home AC
charger.
2. DO NOT CHARGE FOR LONGER THAN 12 HOURS - when using the AC-charger.
3. DO NOT CHARGE FOR LONGER THAN 2 HOURS - when using the optional DC -
charger ( sold separately ). This may cause damage to the battery cells.
STORAGE AND MAINTENANCE OF BATTERY PACK:
During Storage, occasionally charge your battery pack to keep it working as efficient as
possible. Failure to do so will extinguish the life of the battery pack and the ability to
maintain a “full” charge.
2
1. AirBedz XUV air mattress with built-in pump
2. Battery pack
3. AC charger
4. Carrying bag
5. Repair patch kit includes glue
CONTENTS
SET UP GUIDE
11
OTHER GREAT PRODUCTS FROM PITTMAN OUTDOORS
www.pittmanoutdoors.com
Pittman Backseat Mattress
• Inflates in under 2 minutes with the included D.C. portable pump with 6 ft. cord
• Includes one inflatable pillow
• Includes carrying bag and patch kit
• Rugged 300D fabric construction
• A comfortable night's sleep is just an inflate away
• One year limited warranty
• Available colors: Blue, RealTree Camo and Tan
AirBedz Wheel Well Inserts
• AirBedz Wheel Well Inserts convert all your AirBedz mattresses into a regular air mattress for use
in tents or a guest bed in the home
• Available colors:
Blue, Green, RealTree Camo and Tan
Store the battery in a cool, dry location and protected from the elements.
650 South Jefferson Street
Suite D Placentia, CA 92870 for service or repair.
Available for: 100, 200, 300, 400
and 500 series

10 3
OTHER GREAT PRODUCTS FROM PITTMAN OUTDOORS
www.pittmanoutdoors.com
AirBedz Pro3
• Wheel well cutouts allows the mattress to
fit around and over the wheel wells,
creating a sleep area that utilizes the entire
truck bed
• Comfort coil system evenly distributes
weight across a 12" thick mattress,
providing a better night's sleep
• Professional grade fabric construction
• Great for indoor use with "optional" Wheel
Well Inserts
AirBedz Lite
• Includes portable D.C. air pump with 16 ft.
charger cord
• Wheel well cutouts allows the mattress to
fit around and over the wheel wells,
creating a sleep area that utilizes the entire
truck bed
• Flocked top with comfort coil system evenly
distributes weight across a 12" thick
mattress, providing a better night's sleep
• High grade PVC construction
• Inflate/deflate valve for use with included
D.C. pump
• Great for indoor use with "optional" Wheel
Well Inserts
• Built-in pump with detachable rechargeable
battery provides easy inflates and includes a
deflate feature
• Wheel well cutouts allows the mattress to fit
around and over the wheel wells, creating a
sleep area that utilizes the entire truck bed
• Comfort coil system evenly distributes
weight across a 12" thick mattress, providing
a better night's sleep
• Heavy Duty cloth construction
• Secondary inflate/deflate valve for use with
optional pump
• Great for indoor use with "optional" Wheel
Well Inserts
• Includes carrying bag and A.C. charger
• One year limited warranty
AirBedz CAMO
Upon complete deflation, lay bed on flat surface with sleeping surface
facing upwards and fold according to the steps below.
Pump Side
*Bag may vary from illustration
FOLDING INSTRUCTIONS
1 2
3 4
5 6
7 8

49
NOTES
OTHER GREAT PRODUCTS FROM PITTMAN OUTDOORS
www.pittmanoutdoors.com
River Drifter 2
• Built-in ice chest
• 2 Cup/drink holders
• Built-in back rests
• Grab rope
• Mesh bottom
• 2 Heavy-duty handles
River Drifter 1
• 2 Cup/drink holders
• Optional 6-pack cooler available
• Built-in back rest
• Grab rope
• Mesh bottom
• 2 Heavy-duty
handles
Cool Drifter
• Can be used as a stand alone ice cooler or
with traditional coolers up to 48 Qts.
• 4 Cup/drink holders
• Grab rope
• Heavy-duty handle
Splash Pong
• 2 Person inflatable water pong table
• Glow in the dark cup holders
• Contains LED lights around edge of table
Splash Pong X
• 4 Person inflatable water pong table
• Glow in the dark cup holders
INFLATION
1. Place your bed in the back of truck bed or on a flat surface free of debris,
obstructions and sharp objects.
2. Make sure valve cap (A) and middle valve (B) are screwed/pushed into (C).
3. Turn inflate/deflate valve (E) to the inflate position to inflate mattress.
4. Once desired firmness has been achieved, turn inflate/deflate valve (E) to
the “OFF” postion to turn pump off.
OPTIONAL INFLATION PROCEDURE
Each AirBedz®air mattress comes with a secondary inflate/deflate valve (A) for use with
portable air pumps as a back up to the installed automatic pump. To use a portable air pump,
follow these instructions:
1. Open valve cap (A) and insert inflate end of portable pump into the middle valve (B).
(Use proper adapter fitting if needed)
2. Ensure inflate/deflate valve (E) is in the off position.
3. Remove portable pump and switch off. (Fill valve has a built in stopper that will
automatically close when pump is removed stopping any air loss)
4. Replace valve cap and close finger tight only. DO NOT OVER TIGHTEN VALVE CAP!
DEFLATION
NOTE: DEFLATE AIR MATTRESS SLIGHTLY BEFORE REMOVING FROM TRUCK BED TO AVOID
SNAGGING OR TEARING MATTRESS ON TRUCK BED. IT IS BETTER TO FULLY DEFLATE MATTRESS
IN A PLACE TO AVOID DAMAGE.
1. Turn inflate/deflate valve (E) to the deflate position to deflate mattress.
2. Deflate until bed is fully deflated. (For faster deflation, open secondary inflate/deflate
valve (1 or 2).
3. Turn inflate/deflate valve (E) to the “OFF” postion to turn pump off.
4. Fold bed according to Folding Instructions on page 5, place into carrying bag for
storage until next use.
SET UP GUIDE (cont.)
Both of these valves are constructed in
three parts:
A. Valve Cap
B. Middle Valve
C. Bladder Valve
Depending on production date, your AirBedz
mattress may be equipped with either a:
(1) Boston Style Valve or a (2) Two Stage Valve.A
B
C
A
1 2
B
C
1 2
ED

8 5
1. Inspect your bed before each use.
2. Keep your bed away from any sharp or protruding objects. Large cuts, tears or snags
may not be repairable and will not be covered by your warranty.
3. A repair patch kit has been included in case of incidental damage to your bed.
Please follow repair instructions carefully.
4. When not in use store bed in a clean, dry place out of extreme temperatures.
CLEANING
DO NOT SUBMERGE MATTRESS IN WATER! For spot cleaning, use a clean damp cloth to wipe the
surface of the mattress. Apply a clear liquid dish detergent without dye if necessary. Wet stained
area thoroughly; gently massage stained area with detergent. Blot the area to remove staining
substance. Rinse thoroughly and blot dry. Allow your bed to air dry completely after cleaning and
before storing.
IN CASE OF AIR LEAKAGE
Please check the following if there is an air leak.
1. Is the inflate/deflate valve on built-in pump turned to the “OFF” position?
2. Is the secondary inflate/deflate valve cap closed?
A repair patch kit has been included for minor repairs. (Includes patches and glue)
REPAIRING AN AIR LEAK
1. Wipe bed with mild soapy water over area to find possible air leak.
DO NOT SUBMERGE MATTRESS IN WATER! If there is a leak bubbles will form
around leakage area.
2. Follow cleaning instructions for leak area.
3. Use included patch kit to cut a suitable sized patch for leak. Make sure to round the
edges of repair patch to avoid peeling.
4. Apply glue to patch area and around leakage area.
5. Press patch firmly over the puncture area.
6. Wait 24 hours before inflating.
To prevent patch from peeling while drying....
It is recommended to tape down patch edges with a light adhesive tape.
CARE AND MAINTENANCE
ADDITIONAL INFORMATION
WARNING: Cancer and Reproductive Harm
www.P65Warnings.ca.gov
!
• Contains air pump
• Comfort coil system
• Flocked top
• Carrying backpack and patch kit
included
Blue，Purple，Pink
Pittman Kids Mattress
Item No.
PPI-KIDMAT
AVAILABLE IN 3 COLORS
• Built-in electrical air pump for easy
inflation and deflation of your mattress
with convenient cord storage
• Flocked top with comfort coil system
evenly distributes weight across a 20"
thick mattress, providing a better
night's sleep
• High grade PVC construction
• Includes carrying bag and patch kit
Pittman 20" Home Mattress
Item No.
PPI-QCDH2
• Includes portable A.C. air pump with
6 ft. cord. Also includes 3 pump
adapters to air up other inflatables
• Flocked top with comfort coil system
evenly distributes weight across a
16" thick mattress, providing a better
night's sleep
• High grade PVC construction
• Inflate/deflate valve
• Includes carrying bag and patch kit
Pittman 16" Home Mattress
Item No.
PPI-QDHPAC

6 7
AirBedz®Original Truck Bed Air Mattresses are warranted against defects in material and
workmanship for a period of one year from the date of purchase. Problems covered by the
warranty include failure of the pump, seams or the valve. Punctures or wear to the mattress due
to use or abuse are not covered. It is normal for an airbed that has been inflated for extended
periods to require the addition of air after a few days. Air will be lost from the mattress through
the material over time. Also, cooling of the air around the bed will cause the air inside the bed to
contract, and the bed will be softer and may need refilling. To receive a replacement air mattress
under Pittman Outdoors One-Year Warranty, you will need to:
• All returns must have a Returned Goods Authorization number (RGA). Every package
must be clearly marked with the RGA number. RGA numbers are good for 30 days
from the date of issuance. Products returned without viewable RGA numbers will be
refused. No returns on special order, clearance or discounted items. Returned
products is subject to a 20% Re-Box/Restocking fee. Products must be properly
packed to prevent shipping damage. All returned products must be shipped pre-paid.
The cost of transporting the product to Pittman Outdoors for warranty service/
replacement is the responsibility of the purchaser.
• Send entire product to Pittman Outdoors with a letter stating:
- The nature of the problem with the bed and the model number.
- Your name, return shipping address and a daytime phone number.
• Send us a copy of the original sales receipt.
• This warranty is valid for the original retail purchaser from the date of the initial
retail purchase and is not transferable.
The purchase date on the receipt must be within One Year of the date you ship the bed to us.
Please ship the bed, letter and copy of receipt via courier (e.g. UPS, FedEx Ground) or Insured
Post to:
Pittman Outdoors
650 South Jefferson Street
Pittman Outdoors is not responsible for returned shipments lost in transit.You are encouraged
to use a shipment system that offers you a tracking number. Please allow 6 to 8 weeks for
replacement. Customer is responsible for all return shipping costs.
WARRANTY DISCLAIMER
Pittman Outdoors neither assumes nor authorizes any representative or other person to assume
any obligation or liability other than those expressly set forth herein.
YOUR RIGHT UNDER STATE LAW: This warranty gives you specific rights and you may also have
other rights, which vary from state to state.
© 2022 Pittman Outdoors
All rights reserved.
Made in China.
Manufactured pursuant and/or licensed under pending patent applications and one or more of
the following United States patents and/or foreign counterparts thereof:
5,966,755 8,234,349 8,468,624 D597,778 D609,520 D593,349.
China Patent No. ZL20109000106.
Additional U.S. and foreign patents pending.
Our Customer Service Department is available Monday - Friday, 9 AM to 4 PM Pacific Standard
Time, to answer any questions you may have about your new AirBedz®product please call
us toll free at 1 [phone]. U.S.A. or 1 [phone] outside U.S.A.
Unit D
Placentia CA 92870
Pittman Outdoors
650 South Jefferson Street
Placentia CA 92870
1 [phone]
www.pittmanoutdoors.com
Unit D
Contact Pittman Outdoors
EXCEPT FOR THE EXPRESS LIMITED WARRANTY SET FORTH ABOVE, PITTMAN OUTDOORS MAKES
NO EXPRESS OR IMPLIED WARRANTIES IN THIS AGREEMENT OR OTHERWISE. TO THE FULLEST
EXTENT PERMITTED BY LAW, PITTMAN OUTDOORS DISCLAIMS ALL WARRANTIES, WRITTEN,
EXPRESSED OR IMPLIED, INCLUDING ALL WARRANTIES OF MERCHANTABILITY AND/OR FITNESS
FOR A PARTICULAR PURPOSE. PITTMAN OUTDOORS EXPRESSLY DISCLAIMS ANY AND ALL
LIABILITY TO PURCHASER FOR ANY CONSEQUENTIAL DAMAGES, DAMAGES FOR LOSS OF USE,
LOSS OF PROFITS, PROPERTY DAMAGE, OR ANY OTHER INCIDENTAL, CONSEQUENTIAL OR
SPECIAL DAMAGES ARISING OUT OF THIS AGREEMENT OR THEIR OPERATION, FUNCTION OR
CHARACTERISTICS OF THE PRODUCTS PURCHASED HEREUNDER. IT IS EXPRESSLY UNDERSTOOD
THAT THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND EXCLUSIVE REMEDY OF
PURCHASER. NOT WITHSTANDING THE TERMS OF ANY LIMITED WARRANTY, AND/OR IN THE
EVENT ANY LIMITED WARRANTY PROVIDED TO THE PURCHASER FAILS OF ITS ESSENTIAL
PURPOSE, IN NO EVENT WILL PITTMAN OUTDOORS’ ENTIRE LIABILITY TO PURCHASE EXCEED THE
PURCHASE PRICE ACTUALLY PAID BY PURCHASER FOR THE PRODUCTS HEREUNDER, OR ANY
DEFECTIVE PORTION THEREOF, WHICHEVER IS THE LESSER AMOUNT.