Harrod FBL-674 User manual

FBL-674: 7.32x2.44m 3G WTD Euro Portagoal
1. 2 x 7.32m 3G Stadium Crossbar (FEP360)
2. 2 x 2440mm 3G Portagoal Upright (FEP284)
3. 2 x Portagoal Brace 1487mm (PEQ335)
4. 2 x 2270mm Euro P/Goal Sidebar (PEP631)
5. 2 x Senior WTD P/Goal Ali Net Bar (PEQ710)
6. 4 x Euro Portagoal Net Support Bracket (FEP632)
7. 2 x Sen WTD Euro Portagoal Backbar (FEP552)
8. 2 x Euro P/Goal Net Support - Black (PEP639)
9. 2 x Sen WTD Euro Portagoal Ballast Box (FEP551)
10. 4 x 1000x50mm Hockey Solid Ballast (FEP070)
11. 1 x CAM Type Portagoal Wheels (4) (FPK321)
32. 2 x Rear Hi-Raise Wheels (Pair) (FPK282)
2 x Portagoal Brace - Pair (FEP674)
2 x 2270mm Portagoal Sidebar - Pair (FEP631)
1 x Senior WTD P/Goal Ali Net Bar (FEQ805)
2 x Euro Portagoal Net Supports (FEP639)
1 x Weighted Euro Portagoal Fittings (FPK674)
(contains)
(contains)
(contains)
(contains)
7.32x2.44m 3G WTD Euro Portagoal, 6.4x2.13m 3G WTD Euro Portagoal,
4.88x2.13m 3G WTD Euro Portagoal
INS674
Revision 4
04/08/2017
Harrod UK Limited©
Code:
Product:
Pack Contents:
FBL-674, FBL-675, FBL-676
FBL-675: 6.4x2.13m 3G WTD Euro Portagoal
1. 2 x 6.4m 3G Crossbar (FEP361)
2. 2 x 2.13m 3G Portagoal Upright (FEP286)
3. 2 x Portagoal Brace 1487mm (PEQ335)
4. 2 x 2.13m Weighted P/Goal Sidebar (PEP637)
5. 2 x Junior WTD P/Goal Ali Net Bar (PEQ711)
6. 4 x Euro Portagoal Net Support Bracket (FEP632)
7. 2 x Jun WTD Euro Portagoal Backbar (FEP539)
8. 2 x Euro P/Goal Net Support - Black (PEP641)
9. 2 x Jun WTD Euro Portagoal Ballast Box (FEP546)
10. 2 x 5.7m Jun WTD Euro Portagoal Ballast Tube (FEP526)
11. 1 x CAM Type Portagoal Wheels (4) (FPK321)
32. 2 x Rear Hi-Raise Wheels (Pair) (FPK282)
2 x Portagoal Brace - Pair (FEP674)
2 x 2.13m Portagoal Sidebar - Pair (FEP637)
1 x Junior WTD P/Goal Ali Net Bar (FEQ806)
2 x Euro Portagoal Net Supports (FEP641)
1 x Weighted Euro Portagoal Fittings (FPK674)
(contains)
(contains)
(contains)
(contains)
FBL-676: 4.88x2.13m 3G WTD Euro Portagoal
1. 2 x 4.88m 3G Crossbar (FEP378)
2. 2 x 2.13m 3G Portagoal Upright (FEP286)
3. 2 x Portagoal Brace 1487mm (PEQ335)
4. 2 x 2.13m Weighted P/Goal Sidebar (PEP637)
5. 2 x 4.88m WTD P/Goal Ali Net Bar (PEQ712)
6. 4 x Euro Portagoal Net Support Bracket (FEP632)
7. 2 x 9v9 WTD Euro Portagoal Backbar (FEP542)
8. 2 x Euro P/Goal Net Support - Black (PEP641)
9. 2 x 9v9 WTD Euro Portagoal Ballast Box (FEP549)
10. 4 x 1220x50mm Solid Bar (FEP392)
11. 1 x CAM Type Portagoal Wheels (4) (FPK321)
32. 2 x Rear Hi-Raise Wheels (Pair) (FPK282)
2 x Portagoal Brace - Pair (FEP674)
2 x 2.13m Portagoal Sidebar - Pair (FEP637)
1 x 4.88 WTD P/Goal Ali Net Bar (FEQ807)
2 x Euro Portagoal Net Supports (FEP641)
1 x Weighted Euro Portagoal Fittings (FPK674)
(contains)
(contains)
(contains)
(contains) Tools Required
1 x 17mm Spanner
1 x 8mm Allen Key
1x 6mm Allen Key
1 x 4mm Allen Key
1
View of Product
6
Net:-
There is no net supplied with this goal. To purchase a
net please contact our Sales office who will be able to
provide you with a suitable distributor - Please quote
Net Number:
FBL-684 for Senior Goal
FBL-691 for Junior Goal
FBL-696 for 9v9 Goal
IMPORTANT PLEASE READ THE
ASSEMBLY INSTRUCTIONS
CAREFULLY BEFORE STARTING
TOASSEMBLEYOUR GOAL
2
3
8
5
7
11
4
9
10
Inside
Inside
Page 1
Fig. 1a
Please see overleaf for fittings
pack contents
32

FBL-674, FBL-675, FBL-676
Code:
Product: 7.32x2.44m 3G WTD Euro Portagoal, 6.4x2.13m 3G WTD Euro Portagoal,
4.88x2.13m 3G WTD Euro Portagoal
12
13
14
15 16
17 18
19
20 21
22 23
24
25
26
27
28
Fig. 1b
30
31
29
Fittings:
Assembly Steps
22. 4 x B/Supp Top Bracket - Black (PEP328)
23. 16 x M10 x 30 Cap Screw STST (BOL333)
24. 8 x M10 Hex Head Binx Nut (BOL201)
25. 2 x Ali Net Bar Bracket (Pair) (ASY821)
26. 4 x 55mm Net Bar Bracket Plate - White (PEP638)
27. 4 x Euro Portagoal Hook Bracket - Black (PEP844)
28. 1 x Euro Net Hooks - 140 Pack (FPK384)
29. 4 x Portagoal Net Straps (STR110)
30. 1 x 8mm Allen Key (BOL790)
31. 1 x 6mm Allen Key (BOL791)
32. 1 x 4mm Allen Key (BOL793)
33. 1x 30mm Long Spacer (BOL739)
1 x 3G Euro Portagoal Fittings Pack (FPK674)(contains)
12. 60 x M10 x 25 Square Screw 19mm A/F (BOL336)
13. 36 x M10 C Form Washer S/S (BOL709)
14. 4 x 155x75x8mm Steel L-Plate - Tapped (PEP062)
15. 4 x 3G Portagoal Joint Plate 120x38x10 (PEP299)
16. 48 x M10 Nylock Nut BZP (BOL202)
17. 4 x Net Holder (CLP055)
18. 4 x M6 x 10mm A2 SKT Button S/S (BOL672)
19. 8 x Aluminium Football Spacer (APP150)
20. 4 x Bolt M10x40 Socket Button head Screw (BOL321)
21. 4 x M10 Female Handwheel (BOL399)
Fig. 2.1 Fig. 2.2
Fig. 2.3 Fig. 2.4
Page 2
Wheel Fittings
Fittings for the wheels will be included
with the wheels, please refer to the
Instructions included in FPK321.
32
33

Code:
Product:
Assembly Steps
Fig. 2.5
Fig. 2.7
Assembly Instructions
Fig. 3
Fig. 4
13
14 12
1
2
16
13
15
2
3
16
19
2
12
4
Please Note: For safety reasons, It is recommended that two or more people assemble goal.
16
Fig. 2.6
FBL-674, FBL-675, FBL-676
1
2
Use the pack contents to identify and check all the components. The goal
will be assembled in eight stages as shown in Fig 2.
- Lay the crossbar (1), and uprights (2) on the
ground with the slots facing upwards and slide 2 square head bolts (12) into
the slots at both ends of the each crossbar, and 3 square head bolts into the end
of each upright (one of these .
Crossbar and Uprights
will be used to fix the braces (3) at a later date)
- Slide the upright onto the crossbar. Fit the Steel L Plate (14)
onto the bolts in the crossbar and the uprights and secure with washers (13)
and nuts (16), as shown in figure 3.
- Insert four square head bolts into the sidebar and fit the Joint
Plate (15) with washers (13) and nuts (16) (hand tighten 3 nuts and fasten
the last enough to stop the plate sliding down the section when the sidebar is
lifted into position). Lift the side bar into a vertical position and slide onto the
upright. loosen the joint plate and slide into position then fasten as shown in
figure 4. Insert another three square headed bolts into the sidebar, two of which
are for wheel fitting at a later stage. Place an aluminium football spacer (19) on
the free bolt in the upright and the bolt closest to the end of the sidebar, fit a
Portagoal brace (3) onto the spacers and fix in place using an M10 nut (16), as
shown in Fig. 4, taking care to ensure that the sidebar is 90° to the upright. The
goal will now resemble Fig. 2.2.
.
3Crossbar
Sidebar
4
Page 3
7.32x2.44m 3G WTD Euro Portagoal, 6.4x2.13m 3G WTD Euro Portagoal,
4.88x2.13m 3G WTD Euro Portagoal
Sidebar
Upright

5Identify the crossbar edge using the identification label attached.
Feed the crossbar edge through the net holders (17) at each end of the
crossbar as shown in Fig. 5 and fix in place using an M6 x 10mm SKT button
(18).Attach the remainder of the net using the Euro Net hooks (28). Slot the net
into the hook, then slot the hook into the section and twist to lock in. Place one
hook every other mesh in the crossbar, and every other mesh in the uprights and
sidebars as shown in figure 5.
Net -
Evenly space yourselves around the goal, and slowly lift the goal onto its side
bars. If you have optional flip over wheels to fit, you will need to fit a further 4
square head bolts into the slot on each sidebar (these bolts will be supplied with
flip over wheels).
Code:
Product:
Assembly Instructions
7- Slide four square headed bolts (12) into each sidebar and one square headed bolt (12) into each end of the backbar. Slide one
Euro Portagoal Net Support Bracket (6) into each end of the backbar and fix in place using two M10 x 30 Cap Screws (23). Take the backbar
and bracket assembly and slide it into the sidebars as shown in figures 2.4 and 7b, gain, secure in place with two M10 x 30 Cap Screws (23).
Backbar
6- Place the Backbar behind the goal, with the slots facing upwards.
Insert the Ballast Box (9) into the Backbar, ensuring the Ballast Box sits
506mm inset from the end of the Backbar. Then insert the Ballast Tube (10) into
the Ballast Box, as shown in figure 6. This can be solid or tube depending on the
product. Insert one piece of solid at each end of the Backbar to ensure the ballast
is evenly spread, insert the hollow ballast tube so it sits centrally in the Ballast
Ballast
10
9
7
Fig. 7b
12
23
4
6
7
23
6
7
4
Fig. 7a
Wheels
Fit the wheels as shown in the Assembly Instructions included with the wheels (INS606). The wheel
positions are shown in figure 8 and 8a, consult the Wheel Assembly Instructions for Important
operational and Maintenance information
L/H Wheel
R/H Wheel
L/H Wheel
R/H Wheel
Fig. 5
28 18
17
2
1
FBL-674, FBL-675, FBL-676
Fig. 6
Fig. 8
Page 4
7.32x2.44m 3G WTD Euro Portagoal, 6.4x2.13m 3G WTD Euro Portagoal,
4.88x2.13m 3G WTD Euro Portagoal
Fig. 8a
Sidebar Backbar
12
12
12
11
11
32
32
330mm

Code:
Product:
Fig. 12
Fig. 11
FBL-674, FBL-675, FBL-676
22 12
16
27
20
13
21
1Net Bar - Take the Aluminium Net Bar (5) and weave it into the meshes at
the back of the net.At each end of the net bar, slide on anAli Netbar Bracket
(25). Place a Net Bar Bracket Plate (26) over the two free bolts in each sidebar
and place the bracket on top, at this stage hand tighten two Hex Head Binx Nuts
(24) as shown in figure 9.
in place as shown in figure 10.
ll the loop br
2
4
- Take an M10x40mm Bolt (20) and Spacer (33) and screw
it into a Euro Portagoal Hook Bracket (27). Insert an M10 square screw
(12) into the plain hole in the hook bracket and loosely screw on an M10
Female Handwheel (21). Slide the hoop bracket assembly into the Net Support
(8) and tighten the hand wheel to nip the bracket in place. Take a B/Supp
Bracket (22), insert two M10 Square Screws and slide into the section as shown
in figure 10. With the top of the bracket flush with the top of the upright, fix in
place with M10 Washers (13) and M10 nuts (16).
- Take the Net Straps (29) and clip the shorter end onto the top,
back corner mesh. Then count 18 meshes in from the corner and attach the
longer clip to this mesh (mesh number is a rough guide, place the clip at a
distance that creates the desired net shape). Remove the clip from the double
end of the straps and feed them through the B/Supp Bracket, reattach the clip
and clip the straps With the Handwheel
loosened, allowing the loop bracket to slide freely, attach the carbine clip with
the attached headline to the hook bracket. Repeat steps 8 & 9 for the other net
support. Ensure the Rear Wheels have been fitted then slide the net supports
into the corner brackets as shown in Fig. 11.
- With the handwheel loose, pu acket
down the net support upright until the net reaches the desired shape.
Tighten the handwheel to secure the headline. Take care when
loosening the handwheel to adjust the net tension, the tension can cause the
bracket to rise quickly. Once both sides are tensioned, slide the Aluminium net
bar back to tighten the bottom of the net and fix in place using the Binx Nuts
(24).
Net Supports
Net Straps
Tensioning the Net
Caution:
3
Net Assembly
5
25
24
26
12
4Fig. 9
Page 5
7.32x2.44m 3G WTD Euro Portagoal, 6.4x2.13m 3G WTD Euro Portagoal,
4.88x2.13m 3G WTD Euro Portagoal
33
Fig. 10
8
29