airquee Spinning Disc Challenge User manual

Airquee Ltd, Duel House, Llandowlais Street, Cwmbran, NP44 7XB, UK
Additional Operating Instructions
**These are additional instructions to the supplied" Constant Flow Land Inflatables - Operation Manual".**
Thank you for purchasing the
Spinning Disc Challenge
FOR ALL GUIDANCE RELATING TO THE SAFE USE AND OPERATION OF AN INFLATABLE
PLEASE REFER TO OUR CONSTANT FLOW LAND INFLATABLES - OPERATION MANUAL. A
COPY OF THIS WAS SUPPLIED WITH YOUR INFLATABLE. THE CONSTANT FLOW LAND
INFLATABLES - OPERATION MANUAL CAN BE ALSO EMAILED TO YOU UPON REQUEST.
2 ROTATING
MECHANISMS
3 INFLATABLE PARTS
CONNECTED WITH
SANDWICH VELCRO
COVER SHEETS

1
Inclusions
*The listed inclusions are in addition to the ones shown in the main manual. The number and type of
inclusions depends on the model you ordered.
This inflatable can be set up and packed away by 3 persons who have
had proper manual handling training and use the correct equipment to
move the inflatable.
Hazards relating to electrical equipment:
1. The most important rule when handling the mechanisms is to ALWAYS DISCONNECT IT
from its power source when ASSEMBLING THE UNIT, opening the Control Box or the Drive
Motor.
2. The control box and the wiring used within the game are NOT WATER PROOF OR WATER
RESISTANT, therefore we do not recommend operating the unit in the rain. Using electrical
equipment in wet or damp conditions can be dangerous. If you suspect water has entered
any of the electrical components they should not be used until completely dry and tested. We
recommend taking professional advice where necessary.
3. All cables and electrical equipment must be tested in accordance with the regulations of your
country.
4. In accordance with HSE guidelines, all 240v equipment should be protected with an RCD
(Residual Current Device) having a maximum trip current of 30 mA. RCD’s are available from
Airquee or your electrical store.
Set Up:
- The surface where you will install the game must be totally flat and level! An inclined surface
would result in the discs touching the platforms, thus creating heavy friction.
- Roll the 1st mechanism with the help of its wheels to its final place and connect it with the
Control Panel. Take out the wheels and replace them with the supplied legs. In order to do
this, someone has to tilt the mechanism. (see the 2nd picture below) Add the disc to the shaft
of the Drive Motor.
Drive Motor
Wheels
Legs
Leg Covers
Mechanism
Covers
Discs
Platform
Covers
x2
x8
x8
x8
x2
x2
x3
3x

2
How to connect the cables:
- Insert the bolt (marked with a green circle below), tighten it and tighten BOTH hexagonal
bolts as well (marked with yellow circles). Please note the second picture is upside down.
- Add the PVC cover to the drive motor(s).
- Unfold the 1st and 2nd inflatable part around the mechanism. Start velcroing the two parts
together. Connect ALL the Velcro flaps of the mechanism in an uninflated state. You won’t
be able to connect it when inflated.
- Repeat the same procedure with the 3rd inflatable part and the second mechanism.
BOTH DRIVE MOTORS CONNECT
TO THE CONTROL PANEL
THROUGH THE RED CABLES
THE CONTROL PANEL CONNECTS
TO A POWER SOURCE THROUGH
THE BLUE CABLE

3
- Setup and connect BOTH mechanisms and all 3 inflatable parts before you start inflating the
unit.
- After inflation add the three platform covers.
Routine and Yearly Inspections
Routine Inspections (before every use)
After every setup or operation, before opening the game to the public, the controller or his
nominee SHALL PERSONALLY CHECK that the setup of the Spinning Disc Challenge is correct.
We recommend to check for every criteria written below. The person carrying out the check shall
be sufficiently trained or experienced in the check routines that have to be carried out.
Check that:
- Every button is in a working condition on the Control Panel.
- The electrical connection sockets and cables are not chafed nor damaged.
- The Velcro of every cover, bed connection has a good grip and is not weakened, the covers
are not damaged and no accessible parts of the machinery has sharp edges, sharp angles
or rough surfaces to cause injury, and no openings which can “trap” parts of the body or
clothing.
- There are no tears, rips which could represent a safety hazard on the bed and walls.
- All nuts and bolts are secured and tightened.
- The inflatable bed is securely anchored.
- The discs are securely connected to the mechanism.
The device shall not be made available to the public until any adjustments or repairs judged to
be necessary as a result of this inspection have been completed.
Trial runs
Following the check, the controller shall run one or more trial runs without any members of the
public on it, simulating where possible emergency situations to verify particularly that the control
system and the emergency stop works properly. Only now are the users allowed to use the game.
Yearly Examination
Besides the regular checks, the Spinning Disc Challenge should be thoroughly examined at
appropriate intervals by a competent person/institute/organization/company.
SOMEONE HOLDS THE
BED STANDING ON THE
MECHANISM, WHILE
ANOTHER PERSON CONNECTS
THE SANDWICH VELCRO.

4
The intervals between two successive thorough examinations may be governed by existing
national regulations.
Operating Guidelines/Rules of Play
- For safety reasons, users should only stand at the designated jumping platform. Do not allow
anyone to spectate from the bed.
- No one with ANY PRE-EXISTING INJURIES or HEALTH CONCERNS (limitations), in the state
of PREGNANCY or UNDER THE INFLUENCE OF PSYCHOTROPHIC SUBSTANCES may use
the unit.
- Every time a user trips/falls THE MECHANISMS MUST BE STOPPED!
- The operator must adjust the speed of the arms to the abilities of the players.
- Use the Emergency Button only in a case of an emergency. After releasing it, WAIT AT LEAST
5 SECONDS before pressing any other button on the Control Box.
- The MAXIMUM NUMBER OF USERS IS TWO. Do not allow more than 2 users on the game at
one time. High risk of collision.
- The unit should NOT TO BE USED IF IT BECOMES WET. In the event of rain, the unit should
be deflated and folded to prevent water collecting on it.
- The Emergency Stop button MUST ALWAYS BE DEPRESSED AND THE KEY REMOVED
whenever you are setting up the game or leaving the control console unattended.
- Do not press more than one button at a time.
Positioning of the control panel:
The control panel must be positioned so that the operator has an unobstructed view of ALL the
players.
Transporting and storing
DURING TRANSPORTATION, THE MECHANICAL PARTS MUST BE PROTECTED!
When packing away the mechanism for transporting/storing, we advise to:
- remove the keys of the control box.
- do not place anything heavy on the control box or on any part of the mechanism.
- make sure the mechanical parts are packed and protected correctly.
- store the mechanism in dry conditions/in a dry place.
- leave the bolts and nuts on the mechanism in their corresponding holes.
- dry every part (if for any reason it becomes wet).
HAVE FUN!

5
Legal Disclaimer:
The Airquee Additional Operating Instructions (the "Manual") is proprietary to Airquee Ltd and no ownership rights
are hereby transferred. No part of the Manual shall be used, reproduced, translated, converted, adapted, stored in a
retrieval system, communicated or transmitted by any means, for any commercial purpose, including without limitation,
sale, resale, licence, rental or lease, without the prior express written consent of Airquee Ltd.
Airquee Ltd does not make any representations, warranties or guarantees, express or implied, as to the accuracy
or completeness of the Manual. Users must be aware that updates and amendments will be made from time to time to
the Manual. It is the user's responsibility to determine whether there have been any such updates or amendments.
Neither Airquee Ltd nor any of its directors, officers, employees or agents shall be liable in contract, tort or in any other
manner whatsoever to any person for any loss, damage, injury, liability, cost or expense of any nature, including without
limitation incidental, special, direct or consequential damages arising out of or in connection with the use of the Manual.
All logos, images and content not owned by Airquee Ltd are copyright to their respective owners and have been
reproduced by permission.
Your product model, and its inclusions (number and type) may differ from the one presented in this Manual. All the
pictures and drawings contained in this Manual are for illustration purposes only. Any misuse or failure to adhere to the
instructions and recommendations contained in this Manual will render void the warranty.
This additional manual to be sent only for AQ6711. Version 1.1 25/01/2019