airquee HELTER TWIST DOME (LIGHT AND SPEAKER) Operating instructions

Version 1.0 22/09/16
Page 1of 4
HELTER TWIST DOME (LIGHT AND SPEAKER)
AQ5792
IMPORTANT
AS OWNER/OPERATOR IT IS YOUR RESPONSIBILITY TO WRITE AND CARRY OUTYOUR OWN
RISK ASSESSMENTS BEFORE ATTEMPTING TO USE THIS PRODUCT.
Site survey:
1. Carry out a survey of the area where the ‘Helter Twist Dome’ will be located, and
check for any overhead/underground cables. It’s important that this is carried out
to avoid ground anchors penetrating underground services, and the ‘Helter Twist
Dome’coming into contact with overhead cables when inflated.
2. You should provide an adequate power supply to the fan, this should adhere to
your local power regulations.
3. Check wind speed: The industry recommends a maximum wind speed of Force 5
on the Beaufort scale of 28 - 38 kph (19-24 mph). Force 5 is a fresh breeze when
small trees in leaf begin to sway.

Page 2of 4
Included with your ‘Helter Twist Dome’:
The inflatable
in its bag Anchor Pegs
Wiring Harness
–installed in the
unit
Land Operation
Manual
Extra equipment needed in addition what is supplied with your inflatable:
Suitable 240v Power Supply to operate the fan.
Disco light and speaker
Extra equipment you could consider for your new inflatable:
Ground sheet to protect the underside of your inflatable
Sandbag covers to anchor your inflatable indoors.
Sack truck to move your inflatable safely
RCD to attach to you extension lead
Crash Mats
This inflatable can be set up and packed away by 2 people who have had proper manual
handling training and use the correct equipment to move the inflatable.
x2
Set up:
The first step is to unfold the unit according described in the Land Manual.
IMPORTANT: The electrical Items that you choose to use in your inflatable must meet
the safety standards of the country you are operating in. You must ensure all items are
CE marked.
The disco light that you will buy separately for the unit, will be installed after the unit is
unfolded, but before it is inflated. The light should come with a separate instruction manual
which contains the safety instructions you should take into consideration before installing it in
the unit.
The light shown in this instruction manual is for illustrative purposes only –fig.2.
The plug of the light has a protection case, which should be removed, before any further step
(fig.1).

Page 3of 4
fig.2
The light should be inserted in the place that is already marked and cabled. (fig.3a&3b).It is
important that the light needs to be inserted with the clear part facing down. After it is placed
it needs to be plugged in.
fig.3a fig.3b
After the light is inserted in the corresponding place and plugged in, the unit can be inflated.
The disco speaker will be inserted in the unit, after the unit is totally inflated –fig.4
Fig.4
The disco speaker shown in this instruction manual is for illustrative purposes only.
fig. 1

Page 4of 4
It should be placed as seen in the fig.5 and secured with the black straps.
fig.5
IMPORTANT INFORMATION REGARDING YOUR SPEAKER –PLEASE
READ!
Extended exposure to very high volume sound can cause serious damage to hearing. Please
exercise caution when setting the volume and remember that inside the dome the sound is
enclosed and much louder!
Deflation:
Before deflating the unit, the disco speaker will be unplugged and taken out from the unit.
After the unit is deflated the disco light can be taken out.
IMPORTANT:
The speaker, light and electrical wiring used within the unit are not water proof or water
resistant. When inflated, the air pressure will prevent ingress of water into the unit but it
cannot be guaranteed to stop all water reaching the electrical parts. Therefore we do not
recommend operating the unit in the rain.
When the unit is deflated the light and speaker should be removed as soon as possible and
stored safely. The wiring harness should be left in place and the unit should be rolled to
prevent water lying on the unit and seeping into the sockets. If you suspect water has entered
in any of the electrical components they should not be used until completely dry and tested.
We recommend taking professional advice where necessary.
All cables and electrical equipment must be tested in accordancewith the regulations of your
country.
In accordance with HSE guidelines all 240v equipment should be protected with an RCD
having a maximum trip current of 30 mA.