Airxcel 9630-352 User manual

A. THERMOSTAT LOCATION

This thermostat is a sensitive instrument. For accurate temperature control and comfort, the

following considerations should be taken into account:

1. Locate the thermostat on an inside wall about ve feet above the oor.

Pick a dry area where air circulation is good.

2. Do not install thermostat where there are unusual heating

conditions, such as direct sunlight, near heat producing

appliances (televisions, radio, wall lamp, etc.), or a furnace or air

conditioner supply register.

B. INSTALLING THE THERMOSTAT

1. Place mounting screw template against the wall where thermostat will

be mounted.

2. Using supplied screws, mount the template to the wall.

3. Remove plastic from between mounting screws.

4. Connect thermostat wiring to motorcoach wiring.

5. Place thermostat on mounting screws and gently push the thermostat

down to lock the thermostat onto mounting screws.

6. Turn on power to the thermostat.

Caution

This thermostat should be installed by trained technicians only. Adhere to all local and national

codes. Disconnect all power to the system before installing, removing, or cleaning.

Button Functions

UP – Wake thermostat and increase temperature

DOWN – Wake thermostat and decrease temperature

MODE – Wake thermostat, change mode

Note: Hold mode button down for 5 seconds. The thermostat will change from fahrenheit to

celsius or celsius to fahrenheit. The backlight will turn off after ve seconds.

Operation

The display indicates the mode and the room temperature. When the mode button is pressed

once, the thermostat will wake and if your thermostat is equipped with a backlight, the backlight

will illuminate. When the mode button is pressed again, the mode will change. Press the or

button to wake the thermostat, the set temperature will display and ash. Press the or

button again to change the set temperature. The thermostat will go back to sleep mode after 5

seconds if no buttons are pressed.

In electric heat mode, if the heat pump is unable to satisfy the thermostat call, the heat pump

will go into lockout (See heat pump and backup heat example for conditions of heat pump

lockout). When thermostat is in lockout, ELEC will ash on the display.

In gas heat mode, the gas furnace will provide the only source of heat and the heat pump is

locked out.

Temperature

Mode

Range

°F °C

Cooling (set) 33°F to 99°F 1°C to 37°C

Heating (set) 33°F to 99°F 1°C to 37°C

Refer to the operation chart for a more detailed listing of operation sequence.

INSTALLATION, OPERATION

& APPLICATION GUIDE

HEAT PUMP

9630*352*

The thermostat wiring is factory installed by the OEM (Original Equipment Manufacturer). RV

Products suggests the thermostat wiring be a minimum of 18 gauge. The thermostat is intended

for use with a 12 VDC control circuit that does not exceed 1 amp. The thermostat is equipped

with a replaceable 2 amp fuse located on the base of the thermostat. The fuse is designed to

“open” if the circuit is mis-wired or if there is a short in the system. Before replacing the fuse, the

cause of the failure must be located and corrected.

Application

Installation

ELECTRICAL SHOCK HAZARD – Turn off power at the main service panel by

removing the fuse or switching the appropriate circuit breaker to the Off position

before removing the existing thermostat.

05-03-18

1. Download the RVClimate app from either the

Google Play store or Apple App store.

2. Open the app and select “ADD NEW

THERMOSTAT”.

3. On the thermostat, hold the Up and Down

buttons simultaneously to enter pair mode.

4. On the App select “PAIR NEW

THERMOSTAT”.

5. When prompted, enter the 6 digit ID from the

thermostat and select “PAIR”.

6. Once connected the thermostat will revert to

the main screen.

7. Slide screen to the left (2nd screen).

8. Press .

9. Select “ZONE NAME”.

10. Assign a name or description to the thermostat

(7 characters max).

11. Select “SET” to save the assigned name or

description.

Note: Each thermostat may be connected

to a maximum of 4 individual phones.

Any subsequent connections will

result in the oldest/ﬁrst connections being automatically deleted in order.

Pairing additional thermostats

1. Using the RVClimate app.

2. Slide screen to the left (last screen).

3. Select “PAIR NEW THERMOSTAT”.

4. On the thermostat, Hold the Up and Down buttons simultaneously to enter pair mode.

5. When prompted, enter the 6 digit ID from the thermostat and select “PAIR”.

6. Once connected the thermostat will revert to the main screen.

7. Slide screen to the left (2nd screen).

8. Press .

9. Select “ZONE NAME”.

10. Assign a name or description to the thermostat (7 characters max).

11. Select “SET” to save the assigned name or description.

Note: A maximum of 3 units may be added to an individual phone.

Pairing a previously paired thermostat

1. Using the RVClimate app select “ADD NEW THERMOSTAT”.

2. On the thermostat, Hold the Up and Down buttons simultaneously to enter pair mode

3. Thermostat will automatically pair.

Note: If thermostat doesn’t pair automatically, when prompted enter the 6 digit ID from the

thermostat and select “PAIR”.

4. Once pairing is complete, press the thermostat’s mode button to return to the main screen.

Pairing the Thermostat

Wiring Diagrams

Green

Gray

Wht/Blk

Fan Hi

Heat Pump

Fan Lo

Plug Housing

Amp P/N: 1-480702-0

Pin Terminal x2

Amp P/N: 350218-1

Cap Housing

Amp P/N: 1-480703-0

Socket Terminal x4

Amp P/N: 350536-1

From thermostat 9630*352*

White

Red

Blue

Yellow

Furnace

+12 VDC

-12 VDC

Compressor

WHP

Note: When used to replace a thermostat which previously did not use plugs,

please remove the plugs and use wire nuts as needed.

A. THERMOSTAT LOCATION

This thermostat is a sensitive instrument. For accurate temperature control and comfort, the

following considerations should be taken into account:

1. Locate the thermostat on an inside wall about ve feet above the oor.

Pick a dry area where air circulation is good.

2. Do not install thermostat where there are unusual heating

conditions, such as direct sunlight, near heat producing

appliances (televisions, radio, wall lamp, etc.), or a furnace or air

conditioner supply register.

B. INSTALLING THE THERMOSTAT

1. Place mounting screw template against the wall where thermostat will

be mounted.

2. Using supplied screws, mount the template to the wall.

3. Remove plastic from between mounting screws.

4. Connect thermostat wiring to motorcoach wiring.

5. Place thermostat on mounting screws and gently push the thermostat

down to lock the thermostat onto mounting screws.

6. Turn on power to the thermostat.

Caution

This thermostat should be installed by trained technicians only. Adhere to all local and national

codes. Disconnect all power to the system before installing, removing, or cleaning.

Button Functions

UP – Wake thermostat and increase temperature

DOWN – Wake thermostat and decrease temperature

MODE – Wake thermostat, change mode

Note: Hold mode button down for 5 seconds. The thermostat will change from fahrenheit to

celsius or celsius to fahrenheit. The backlight will turn off after ve seconds.

Operation

The display indicates the mode and the room temperature. When the mode button is pressed

once, the thermostat will wake and if your thermostat is equipped with a backlight, the backlight

will illuminate. When the mode button is pressed again, the mode will change. Press the or

button to wake the thermostat, the set temperature will display and ash. Press the or

button again to change the set temperature. The thermostat will go back to sleep mode after 5

seconds if no buttons are pressed.

In electric heat mode, if the heat pump is unable to satisfy the thermostat call, the heat pump

will go into lockout (See heat pump and backup heat example for conditions of heat pump

lockout). When thermostat is in lockout, ELEC will ash on the display.

In gas heat mode, the gas furnace will provide the only source of heat and the heat pump is

locked out.

Temperature

Mode

Range

°F °C

Cooling (set) 33°F to 99°F 1°C to 37°C

Heating (set) 33°F to 99°F 1°C to 37°C

Refer to the operation chart for a more detailed listing of operation sequence.

INSTALLATION, OPERATION

& APPLICATION GUIDE

HEAT PUMP

9630*352*

The thermostat wiring is factory installed by the OEM (Original Equipment Manufacturer). RV

Products suggests the thermostat wiring be a minimum of 18 gauge. The thermostat is intended

for use with a 12 VDC control circuit that does not exceed 1 amp. The thermostat is equipped

with a replaceable 2 amp fuse located on the base of the thermostat. The fuse is designed to

“open” if the circuit is mis-wired or if there is a short in the system. Before replacing the fuse, the

cause of the failure must be located and corrected.

Application

Installation

ELECTRICAL SHOCK HAZARD – Turn off power at the main service panel by

removing the fuse or switching the appropriate circuit breaker to the Off position

before removing the existing thermostat.

05-03-18

1. Download the RVClimate app from either the

Google Play store or Apple App store.

2. Open the app and select “ADD NEW

THERMOSTAT”.

3. On the thermostat, hold the Up and Down

buttons simultaneously to enter pair mode.

4. On the App select “PAIR NEW

THERMOSTAT”.

5. When prompted, enter the 6 digit ID from the

thermostat and select “PAIR”.

6. Once connected the thermostat will revert to

the main screen.

7. Slide screen to the left (2nd screen).

8. Press .

9. Select “ZONE NAME”.

10. Assign a name or description to the thermostat

(7 characters max).

11. Select “SET” to save the assigned name or

description.

Note: Each thermostat may be connected

to a maximum of 4 individual phones.

Any subsequent connections will

result in the oldest/ﬁrst connections being automatically deleted in order.

Pairing additional thermostats

1. Using the RVClimate app.

2. Slide screen to the left (last screen).

3. Select “PAIR NEW THERMOSTAT”.

4. On the thermostat, Hold the Up and Down buttons simultaneously to enter pair mode.

5. When prompted, enter the 6 digit ID from the thermostat and select “PAIR”.

6. Once connected the thermostat will revert to the main screen.

7. Slide screen to the left (2nd screen).

8. Press .

9. Select “ZONE NAME”.

10. Assign a name or description to the thermostat (7 characters max).

11. Select “SET” to save the assigned name or description.

Note: A maximum of 3 units may be added to an individual phone.

Pairing a previously paired thermostat

1. Using the RVClimate app select “ADD NEW THERMOSTAT”.

2. On the thermostat, Hold the Up and Down buttons simultaneously to enter pair mode

3. Thermostat will automatically pair.

Note: If thermostat doesn’t pair automatically, when prompted enter the 6 digit ID from the

thermostat and select “PAIR”.

4. Once pairing is complete, press the thermostat’s mode button to return to the main screen.

Pairing the Thermostat

Wiring Diagrams

Green

Gray

Wht/Blk

Fan Hi

Heat Pump

Fan Lo

Plug Housing

Amp P/N: 1-480702-0

Pin Terminal x2

Amp P/N: 350218-1

Cap Housing

Amp P/N: 1-480703-0

Socket Terminal x4

Amp P/N: 350536-1

From thermostat 9630*352*

White

Red

Blue

Yellow

Furnace

+12 VDC

-12 VDC

Compressor

WHP

Note: When used to replace a thermostat which previously did not use plugs,

please remove the plugs and use wire nuts as needed.

Conditions of Heat Pump Lockout (Set Point 70°F)

Operation Chart

The chart below shows the system functions. After the entire air conditioning and heating

system is installed, check each position function.

*There is a 3 minute anti-short cycle delay timer built into the thermostat.

Mode Call Operation

Fan Low No GL-Fan Low (Gray) energized

Fan Hi No GH-Fan High (Green) energized

Cool On

High No GH-Fan High (Green) energized

Cool On

High Yes GH-Fan High (Green) energized, Y-Compressor (Yellow) energized

Cool On

Low No GL-Fan Low (Gray) energized

Cool On

Low Yes GL-Fan Low (Gray), Y-Compressor (Yellow) energized

Cool Auto

Low No No function occurs

Cool Auto

Low Yes GL-Fan Low (Gray) energized, Y-Compressor (Yellow) energized

Cool Auto

High No No function occurs

Cool Auto

High Yes GH-Fan High (Green), Y-Compressor (Yellow) energized

Heat Gas No No function occurs

Heat Gas Yes W-Furnace (White) energized

Electric

Heat No No functions occur in this mode

Electric

Heat Yes WHP - Heat Pump (White/Black) will be energized

Electric

Heat

Backup

Yes (5°

Below

Setpoint)

WHP - Heat Pump (White/Black) and WF-Furnace (White) will be

energized

Indoor

Temp (°F)

Operation

of Unit

70+ No operation.

69 Heat pump turns on as primary heat source.

71 Heat pump turns off, thermostat is satised.

69 Heat pump turns on as primary heat source.

65 Gas heat turns on at 5 degrees from rst stage (heat pump cannot satisfy

demand). First Strike on backup counter.

71 Gas heat and heat pump turn off, thermostat is satised.

69 Heat pump turns on.

65 Gas heat turns on at 5 degrees below rst stage (heat pump cannot satisfy

demand). Second Strike on backup counter.

71 Gas heat and heat pump turn off, thermostat is satised.

69 Heat pump turns on.

65 Gas heat turns on at 5 degrees from rst stage (heat pump cannot satisfy

demand).

Third Strike on backup counter. Heat pump is locked out for 1 hr. 45 min.

Backup counter reset if heat pump runs for 20 minutes with no call for back up heat.

71 Gas furnace turns off, thermostat is satised.

69 Gas furnace turns on, primary heat source during lockout.

71 Gas furnace turns off, thermostat is satised.

1 hour 45 minute lockout ends.

69 Heat pump turns on and is restored to the primary heat source.

65 Gas furnace turns on and becomes the primary heat source. Heat pump

turns off for another 1 hour and 45 minutes.

71 Gas furnace turns off, thermostat is satised.

1 hour 45 minute lockout ends.

69 Heat pump turns on and resumes primary heat source function.

71 Heat pump turns off, thermostat is satised.

Conditions and example for resetting the backup counter

69 Heat pump turns on.

65 Gas heat turns on at 5 degrees from rst stage (heat pump cannot satisfy

demand).

First Strike on backup counter.

71 Gas heat and heat pump turn off, thermostat is satised.

69 Heat pump turns on.

65 Gas heat turns on at 5 degrees from rst stage (heat pump cannot satisfy

demand).

Second Strike on backup counter

71 Gas heat and heat pump turn off, thermostat is satised.

69 Heat pump turns on and runs for 20 minutes without a call for backup heat.

71 Heat pump turns off, thermostat is satised (backup counter reset).

69 Heat pump turns on.

65 Gas heat turns on at 5 degrees from rst stage (heat pump cannot satisfy

demand).

First strike on backup counter

Backup timer will reset anytime the Heat Pump operates for more than 20 minutes

and satises the thermostat without calling for backup heat.

ZONE NAME: Assigns a name or

description to the

thermostat (maximum of 7

characters).

THERMOSTAT ID: Displays thermostat’s

6 digit ID

FUNCTIONS: Displays available modes.

SET: Saves assigned zone name/

description.

CANCEL: Reverts to main screen.

REMOVE THERMOSTAT: Removes

thermostat from the RV Climate app.

Controlling the

thermostat via RV

Climate app

1. Slide screen to the left (2nd screen).

2. Tap the icon displaying the current

settings [Kitchen 75 FAN HIGH].

3. Select the desired temperature/mode.

4. Press “SET”.

Removing a previously paired thermostat

1. Using the RV Climate app, slide screen to the left (2nd screen).

2. Press .

3. On the following page select “REMOVE THERMOSTAT” and press “OK”.

Details (2nd Screen)

RV Products

A Division of Airxcel, Inc., P.O. Box 4020, Wichita, KS 67204

www.Airxcel.com LIAF253

This device complies with part 15 of the FCC Rules. Operation

is subject to the following two conditions: (1) This device may

not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause

undesired operation.

NOTE: This equipment has been tested and found to comply with the limits

for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense.

Contains FCC ID: WAP4110