aivituvin AIR 75 User manual

INSTRUCTION
MANUAL
AIR 76
www.aivituvin.com
AIR 75

Please retain these instructions for future reference.
NOTICE
Firmly secure all bolts,screws and knobs before use.
Reconfirm that all bolts,screws,and knobs are secure every 90
days.
Fasten screws loosely during initial assembly. Do not fully
tighten screws until the item is completely assembled.
Do not use or store this item in the proximity of open flame or
flammable/combustible chemicals.
Be aware that some parts are heavy and have sharp edges.
Be aware that moving parts can injure,crush and cut.
If any parts are missing,broken,damaged,or worn,stop using
this product until repairs are made and/or factory replacement
parts are installed.
01
Do not use this item in a way inconsistent with the manufacturer’
s instructions as this could void the product warranty.

TOOLS REQUIRED
PHILLIPS
SCREWDRIVER
DRILL
(RECOMMENDED)
2PERSON
ASSEMBLY
APPROXIMATELY
30MIN. ASSEMBLY
HARDWARE
P1 P2
P3 P4
02
M3.5x45mm SCREW
M3.0x18mm SCREW
M6.0x30mm SCREW
10PCS+1spare
8PCS+1spare 6PCS+1spare
P5 P6
Hinge
2PCS
M3.0x14mm SCREW
10PCS+1spare
M3.0x12mm SCREW
4PCS+1spare
P7
Lock
1PC

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
03
AB C
1PC
Back panel
D
1PC
Left side panel
E
1PC
F
1PC
Back metal bar-left
HI
1PC
Bottom pad
G
1PC
Right side panel
Back metal bar-right
2PCS
Bottom pad
1PC
Front panel
2PCS
Bottom floor

PARTS
A B C
C1 D E
F
Side panel
1PC
Bottom panel
1PC
Bottom panel
1PC
Asphalt roof
1PC
1PC 1PC 1PC
04
J K L
1PC
1PC
Front metal bar-left Front metal bar-right
M N
1PC
4PCS Roof
1PC
PVC curtain
Plastic feet

PRODUCT ASSEMBLY
01
02
05
Attach the plastic feet Part M to the metal bars Part D & E with the
buckle.
M
E
M
D
Attach the panel Part A, B, C with the metal bars Part D & E by 4xP1
screws.
A
B
C
P1
X4
D
E

PRODUCT ASSEMBLY
03
04
05
Screw the curtain Part J to the INSIDE of Part I by 4xP3 screws.
P3X
4
I
J
Attach the plastic feet Part M to the metal bars Part K & L with the
buckle.
K
M
L
M

PRODUCT ASSEMBLY
05
06
07
Attach the Part I to the house with the metal bars Part K& L by 4XP1
screws.
P1
X4
K
L
Attach the bottom pad Part G to the side of bottom floor Part H by 1XP2
screws
①Attach the bottom pad Part G & F to the side of bottom floor Part H by
3XP2 screws.
②
P2
X1
H
G
F
G
P2
X3
H
Left
Right

PRODUCT ASSEMBLY
07
08
08
Put down the left bottom floor first,and then put down the right bottom
floor,finally connect the bottom floor with bottom pad Part F by 2XP2
screws.
P2
X2
Screw the roof Part N on asphalt part from bottom by 6xP3 screws.
Notice:The roof edges of back are relatively flat，pls pay attention the
position N
P3
X6

PRODUCT ASSEMBLY
09
09
Screw the roof hinge P6, one side to the roof by 2xP4 screws, the other
side to the side panel by 2xP4 screws in left and right sides.
P
6
X2
P4
X8
10
Screw the lock P7, screw one side to roof by 2xP4 screws,screw the
other to front panel by 4xP5 screws.
P7
X1
P5
X4
P4
X2

PRODUCT ASSEMBLY
11
10
Complete.
Finish

WARNING
Manufacturer and seller expressly disclaim any and all liability for personal injury,property
damage or loss,whether direct,indirect,or incidental,resulting from the incorrect
attachment,improper use,inadequate miantenance,or neglect of this product.