AJA Hi5-3D Original operating instructions

®
Installation & Operation Guide
Version 2.0
Published: April 23, 2014
Hi5-3D
HD-SDI 3D Multiplexer

Hi5-3D v2.0 www.aja.com
2
Table of Contents
Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Copyright. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Contacting Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Chapter 1: Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3D Modes Supported . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Format Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
I/O Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Chapter 2: Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
USB Control and Setup—Using AJA MiniConfig . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installing MiniConfig on a Mac . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Installing MiniConfig on a PC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Running MiniConfig . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
PC Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Mac Startup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Saving Setups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Operating MiniConfig. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Tabbed Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Video Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Audio Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Update Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Software Update Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Info Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Appendix A: Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Input Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Video Inputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Video Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Audio Outputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Appendix B: Safety and Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Federal Communications Commission (FCC) Compliance Notices. . . . . . . . . . . . . . . . . . . 17
Class A Interference Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
FCC Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Canadian ICES Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
European Union and European Free Trade Association (EFTA)
Regulatory Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Declaration of Conformity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Hi5-3D v2.0 www.aja.com
3
Korea KCC Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Taiwan Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Japanese Compliance Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Translated caution statements, warning conventions and warning messages . . . . . . . 20
Before operating your Mini-Converter, please read this document . . . . . . . . . . . . . . . . . . 20
Warranty Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Hi5-3D v2.0 www.aja.com
4
Notices
Trademarks
AJA®, KONA®, Ki Pro®, KUMO® and XENA® are registered trademarks of AJA Video, Inc.,
TruZoom™, TruScale™, Ki Pro Mini™, Io Express™, Io HD™, Io™, and AJA Control Room™ are
trademarks of AJA Video, Inc. AirPort, Apple, the Apple logo, AppleShare, AppleTalk,
FireWire, iPod, iPod Touch, Mac, and Macintosh are registered trademarks of Apple
Computer, Inc. Final Cut Pro, QuickTime and the QuickTime Logo are trademarks of Apple
Computer, Inc. Avid, Avid Media Composer and Avid DNxHD are trademarks of Avid
Technology, Inc. All other trademarks are the property of their respective holders.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC. DVI is a registered trademark of DDWG. All
other trademarks are the property of their respective holders.
Copyright
Copyright © 2014 AJA Video, Inc. All rights reserved. All information in this manual is
subject to change without notice. No part of the document may be reproduced or
transmitted in any form, or by any means, electronic or mechanical, including
photocopying or recording, without the express written permission of AJA Inc.
Contacting Support
When calling for support, have all information at hand prior to calling.
To contact AJA Video for sales or support, use any of the following methods:
Telephone: [phone]
FAX: [phone]
Web: http://www.aja.com
Support Email: [email protected]
Sales Email: [email protected]

Hi5-3D v2.0 www.aja.com
5
Chapter 1: Introduction
The Hi5-3D is a 3D video multiplexer that combines two HD-SDI Inputs into various
multiplexed 3D formats for output on HDMI 1.4a and HD-SDI. Non-3D input (SD-SDI, HD-
SDI) at either input will be passed to the HDMI output.
The HDMI 1.4a output supports EDID transactions that allow automatic 2D/3D
configuration per the HDMI monitor’s capabilities. Input SDI 2 will be frame synchronized
to input SDI 1 in 3D Modes.
Embedded SDI input audio is embedded in both the HDMI and SDI outputs. 2 channel
RCA audio output is also supported with user control of channel selection. The Hi5-3D
supports AJA’s Mini-Config application for user configuration and firmware download.
Features
• HD-SDI to HDMI 1.4a with additional SDI output
• Non-3D SD/HD-SDI passed to HDMI output
• 10-bit HDMI 1.4a support including 3D and embedded audio
• Frame-sync mode for HD formats: the right eye will be frame synchronized to the left
eye.
• Anaglyph mode for calibrating 3D camera rigs (only luma data preserved)
• Additional 2-Channel RCA jack audio output
• Setup via Dipswitch or PC/Mac using USB port and supplied USB cable (USB
configuration software application supplied on CD)
• Uses universal input +5V power supply AJA model DWP-U-R1 (included)
• 5 year warranty
Block Diagram
Figure 1. Hi5-3D Converter, Simplified Block Diagram
3D
Multiplexing
and SDI
Processing
Audio
D/A
Video
Audio
HDMI
Transmitter
Video with Embedded Audio
2-Channel
Analog Audio
Monitor Output
HDMI 1.4a Output
with Embedded
Audio
SD/HD/3G-SDI
Input 1
SD/HD/3G-SDI
SDI Receiver
SD/HD/3G-SDI
Input 2
USB Port
(connect to PC or Mac)
Selects 8 o 10-bit Video
and other Functions
SDI Receiver

Hi5-3D v2.0 www.aja.com
6
3D Modes Supported
The Hi5-3D supports, depending on the video format, “side-by-side”, “top-bottom”, and
“frame-packing” 3D modes. The “side-by-side” and “top-bottom” modes involve
compressing, either horizontally or vertically, each input for combining into a single
video stream at the same rate of the inputs.
The “frame-packing” mode stacks two full resolution inputs into a “tall” frame (at twice
the clock and line rates). When selected, “frame-packing” works only with the following
formats: 1080p23.98, and 1080p24. (Frame-packed mode does not support psf inputs at
this time.) When operating in frame-packing mode, the SDI output will be black; the valid
output is the HDMI connector.
Each input, in addition to 3D processing, can be flipped either horizontally, vertically, or
both. This control is provided by 4 switches that can be engaged in any combination—or
by use of the supplied AJA Mini Config software (Mac/PC).
Note: The Flip function is only active when in 3D mode and does not apply for pass-
through of 2D SDI inputs.
Format Support
The Hi5-3D works with both 2D and 3D inputs. When in the 2D mode, the input is simply
passed to the output unmodified—or flipped (via dipswitch or Mini Config software
selection). In the 3D mode, the Hi5-3D supports the required 3D modes as defined by the
CEA for HDMI 1.4a televisions.
CEA Required 3D modes:
NOTE: • “psf” inputs are converted to “p” for HDMI and SDI output.
• The SDI output can support S/S and T/B formats only.
• Future software versions may add other frame rates.
• When a 525 or 625 source is on both inputs, the Hi5-3D will only output one of the
sources, defaulting to Input 1. In the absence of Input 1, it will output Input 2. There are
no 3D modes with SD sources; output is simply passed through.
2xSDI 1.5gb 720p50/59.94/60 T/B
2xSDI 1.5gb 1080p23.98/24 T/B, FP
2xSDI 1.5gb 1080psf23.98/24 T/B, FP
2xSDI 1.5gb 1080i50/59.94 S/S

Hi5-3D v2.0 www.aja.com
7
I/O Connections
Figure 2. Hi5-3D Converter
Installation
Typically, Hi5-3D installation consists of the following steps:
1. Ensure the Hi5-3D is disconnected from power.
2. Connect video equipment to the convertor BNCs and HDMI connector.
3. Connect audio equipment to RCA connectors (optional)
4. Apply power to the converter (AJA power supply included).
5. The Hi5-3D will now run using the default factory settings. If you wish to alter the
factory settings, you’ll need to install the AJA Mini Config software (supplied on CD)
on a computer, attach the Hi5-3D via USB to the computer, and then make your
changes. This process is detailed on the following pages.
SD/HD-SDI
+ 5 to 20 VDC
Power
Input
2-Channel
Unbalanced
Analog
Audio
(RCA Jacks)
Output
HDMI Connector
Input 1 BNC
SD/HD--SDI
Input 2 BNC
USB
Port
Red: Lock to HD-SDI
Green: Lock to SD-SDI
LOCK LED
SD/HD-SDI
Output

Hi5-3D v2.0 www.aja.com
8
Chapter 2: Operation
USB Control and Setup—Using AJA MiniConfig
The Hi5-3D can usually be used right out of the box for most applications since it is
designed to recognize inputs and perform standard actions automatically by default.
However you can also manually configure the unit using a supplied software application
for PCs and Macs called “MiniConfig.” This same application can be used to update Mini-
Converter firmware released by AJA.
Installing
MiniConfig on a Mac
To install the application on a Mac, insert the CD supplied with the
Mini-Converter into the computer, drag the “AJA MiniConfig”
application for your platform (Mac or PC) to your desktop or an
applications folder.
NOTE: Macintosh computers must be Intel-based (G5, G4 and earlier models will not work with
MiniConfig).
Installing
MiniConfig on a PC
To install the application on a Windows PC, insert the CD supplied with the Mini-
Converter into the computer, locate the “MiniInstaller” application, and then double-
click it.
Figure 3. MiniConfig Setup Wizard on PC
A Setup Wizard will guide you through the installation. Just click Next to begin.
Answer all questions in the subsequent dialogues; when done, you will be able to locate
the MiniConfig application in the AJA folder in the Programs listing.

Hi5-3D v2.0 www.aja.com
9
Running MiniConfig Connect the Mini-Converter to the PC or Mac via the supplied USB cable. Connect the
external power supply (supplied) to the Mini-Converter.
PC Startup To run MiniConfig on a PC, find the AJA MiniConfig in the program list and locate the AJA
MiniConfig application.
Figure 4. PC MiniConfig Startup
Mac Startup To run MiniConfig on a Mac, double-click the Applications folder and locate the AJA
MiniConfig application. Double-click the application to launch it.
Figure 5. Mac MiniConfig Startup
NOTE: On a Mac, when the Mini-Converter is connected to the USB port, you may see an alert like
that shown below. If you do, press Cancel—this alert can be ignored.
Figure 6. Mac Network Message (ignore)
Saving Setups A File menu at the top of the MiniConfig application menu bar allows you to Save the
state of the Mini-Converter, with your current settings, to a file for later recall. This allows
you to set up the converter for different applications, storing each (with Save) to a unique
name for easy recall—using the Open menu item. A Revert to Factory Settings menu item
similarly allows you to change the settings back to AJA’s factory defaults. An Edit menu
allows you to cut and paste values to/from fields, just as in other applications.

Hi5-3D v2.0 www.aja.com
10
Operating
MiniConfig
The MiniConfig application provides a graphic interface for viewing settings and
updating software. It consists of an information area at the top that shows the available
Mini-Converters attached to the computer via USB, with a graphical rendering of the
selected Mini-Converter showing all the connectors and their current state.
Colored text next to the connectors indicates the signal type and what the Mini-
Converter is doing:
•Blue text indicates the values automatically selected
•Black text indicates values that you have manually selected
•Red text indicates the Mini-Converter is not detecting a signal or cannot negotiate with
the attached device
NOTE: Even if no output device is detected, it still shows the signal it is outputting.
NOTE: Configuration settings in red will change based on the attached output device as well as input
signals. For improved accuracy and reliability, you should configure the Mini-Converter only
when the target output device is attached and input signals are supplied at the inputs.
Screens are virtually the same on both PC and Mac, with subtle differences that reflect
the general look of the platform environment.
Running Multiple Mini-
Converters:
MiniConfig can manage multiple AJA Mini-Converters connected via USB—even when
they are of differing types. However it only connects to one at a time. You can choose
which Mini-Converter you wish to control using the pulldown menu in the upper right
hand corner. If you want to configure and update multiple Mini-Converters in parallel,
you can do it by running multiple instances of the MiniConfig application and have each
control a different Mini-Converter.
Figure 7. MiniConfig, Video Screen
S
elect a USB
po
rt and
an
attached
M
ini-Converter
(name in pa
rentheses)
Tabbed screens
Status message
Firmwar
e
Version
and
Serial
Number
Each
connector
is labelled with the
si
gnals currently
de
tected or manually
sele
cted.
Blue =
Auto
Black =
Manual
selection
R
ed = No signal or
signal output
since device
not detected

Hi5-3D v2.0 www.aja.com
11
NOTE: LEDs adjacent to each SDI input connector indicate by color the detected signal type. Green is
SD-SDI, red is HD-SDI.
Selecting a Mini-Converter with the dropdown menu causes this application to connect
to the selected converter. The graphic of Mini-Converter and text below it provides:
• Type of converter
• Firmware version
• Serial number of the unit
A status field at the bottom of the screen shows if your application is connected and
communicating with the Mini-Converter.
When configuring the Mini-Converter, select it from the top pulldown, view the current
settings and change any values. Making a change communicates that new value to the
Mini-Converter’s non-volatile memory.
Tabbed Screens The Tabs delineate control screens with groups of controls for each type of task to be
performed. The controls for the actual configuration parameters are specific to each
Mini-Converter type. Click on any of the tab buttons and the screen below will change to
match. Each of these screens are described on the following pages.
Video Tab Screen With your Mini-Converter connected and selected, you’ll click on the Video tab to view
and make changes to the converter’s Video I/O settings.
Any changes you make are immediately implemented and are saved, overwriting
previous settings.
Figure 8. MiniConfig, Video Tab Screen

Hi5-3D v2.0 www.aja.com
12
Input Video Selections:
SDI Select—use to select a specific SDI input (1 and/or 2) or select automatic mode.
• Auto: directs the Hi5-3D to automatically select the input based on the signals detected
at the two SDI Input BNCs.
• SDI 1: manually select the signal present at SDI Input 1.
• SDI 2: manually select the signal present at SDI Input 2.
• 3D SDI 1+2: manually select the signals present at SDI Inputs 1 and 2 as a 3D two input
stream (right/left channels respectively).
Left Flip—use to select how the left eye channel input will be flipped (if any).
• None: no flipping; the signal is unaltered.
• Horizontal: left eye channel is flipped horizontally.
• Vertical: left eye channel is flipped vertically.
• Horiz/Vert: left eye channel is flipped horizontally and vertically.
Right Flip—use to select how the right eye channel input will be flipped (if any).
• None: no flipping; the signal is unaltered.
• Horizontal: right eye channel is flipped horizontally.
• Vertical: right eye channel is flipped vertically.
• Horiz/Vert: right eye channel is flipped horizontally and vertically.
3D Mode—use to select the type of CEA 3D mode:
• Auto: lets the Hi5-3D automatically select a 3D mode based on the HDMI 1.4a device it
is connected and negotiating with (blue text shows what it chooses).
• Side by Side: select left/right eye channels are compressed and placed side by side.
• Top Bottom: select left/right eye channels are compressed and placed one on top of
the other
• Frame Packed: select left/right eye channels into a single full-resolution (but tall) frame,
at twice the clock and line rates. When selected, “frame-packing” works only with the
following formats: 1080p23.98, and 1080p24.
(Framepacked mode does not support psf inputs at this time.)
• Anaglyph: used for calibrating camera rigs, this mode shows both stereo images
overlaid as a single image for viewing using anaglyph glasses. In this implementation
only the luma data is preserved.
NOTE: 525 and 625 are passed through to the output without 3D processing.
Protocol—use to select the signal protocol used for the HDMI output connector.
• Auto: lets the Hi5-3D automatically select a protocol based on the device it is
connected and negotiating with at the HDMI connector (blue text shows what it
chooses).
• HDMI: selects HDMI signal protocols.
• DVI: selects DVI signal protocols (note: an HDMI to DVI adapter should be used when
connecting DVI devices).

Hi5-3D v2.0 www.aja.com
13
Color Space—use to select type of RGB or YCbCr colorspace. The choices are:
• Auto: lets the Hi5-3D automatically select a protocol based on the device it is
connected and negotiating with.
•RGB8Bit
•RGB10Bit
•YCbCr10Bit
RGB Range—use to select type of RGB color range, when RGB has been selected as the
color space. Choices are:
• Auto: lets the Hi5-3D automatically select a protocol based on the device it is
connected and negotiating with.
•SMPTE
•FullRange
Audio Tab Screen The Audio Screen is where you can configure Hi5-3D digital and analog audio settings.
Pulldown menu settings are described following the screen graphic.
Figure 9. Mini Config, Audio Screen
HDMI Audio—use to select how many SDI channels are passed to the HDMI connector
and which channel pairs are selected. Choices are:
• Auto: lets the Hi5-3D automatically select an HDMI audio output configuration based
on it communicating with the attached HDMI device and determining its
configuration.
• 2-Channel: output 2 channels from the SDI stream to two channels on the HDMI output
connector. Which 2 channels are selected mirrors the Analog Audio setting (below).
• 8-Channel: output SDI channels 1 through 8 to the HDMI output connector.

Hi5-3D v2.0 www.aja.com
14
Analog Audio—use to select the channel pair that will be output to the Analog RCA
connectors (L/R).
• Channel 1+2: output channels 1 & 2 from the SDI stream to the two Analog Audio RCA
connectors (L/R).
• Channel 3+4: output channels 3 & 4 from the SDI stream to the two Analog Audio RCA
connectors (L/R).
• Channel 5+6: output channels 5 & 6 from the SDI stream to the two Analog Audio RCA
connectors (L/R).
• Channel 7+8: output channels 7 & 8 from the SDI stream to the two Analog Audio RCA
connectors (L/R).
Update Tab Screen Use this Update screen to view the software version currently installed on the converter
or install new software.
Figure 10. MiniConfig, Update Screen
NOTE: When discussing Mini-Converters, “Firmware” is software that will be stored in the Mini-
Converter’s non-volatile memory and used when it is powered up. This is something different
than the MiniConfig application software. The version numbers shown in the Update screen
refer only to the firmware.
The following fields and control are present in this screen:
Installed: This field shows the version of the firmware currently installed inside the Mini-Converter.
Desired: This field shows the version of firmware embedded in the MiniConfig application which
you can install into the Mini-Converter by clicking the Update button.
Update: This button initiates a software update operation loading the “Desired” version of
firmware into the Mini-Converter’s non-volatile memory.
Progress: This indicator bar shows the progress of software being installed.

Hi5-3D v2.0 www.aja.com
15
Software Update
Procedure
1. Check the AJA website for new MiniConfig software for your Mini-Converter. If new
software is found, download it and uncompress the file archive (zip). Here is the URL
to use when checking:
http://www.aja.com/en/products/mini-converters/mini-config-software
2. Connect the Mini-Converter to a Mac or PC via a USB port on the computer and run
the new MiniConfig software just downloaded.
3. Click on the Update tab screen.
4. Check the Installed version level against the Desired version level. If the Desired is
newer, then click the Update button to download the new firmware to the Mini-
Converter.
Progress will be shown via the Progress thermometer bar, and when completed an
“Update Succeeded” message appears.
Info Tab Screen This screen provides basic information about the Mini-Converter. This information is
mostly useful when calling AJA Support for service or technical support.
Figure 11. MiniConfig, Info Screen
Name: This field allows you to give your Mini-Converter a name. This may be useful if you have
several Mini-Converters attached to a Mac/PC via USB so you can distinguish one of them
easily (especially if they’re the same model).
Type: This is the factory set model name of the Mini-Converter (HA5-Plus).
Assembly: This is the factory assembly number.
Serial Number: This is the factory set unique serial number of your Hi5-Plus. If you ever call AJA Support
for service, you may be asked for this number.

Hi5-3D v2.0 www.aja.com
16
Appendix A: Specifications
Input Formats • 720p 50/59.94/60
• 1080i 50/59.94/60
• 1080p23.98
• 1080p24
• 1080p25
Video Inputs • Dual HD-SDI (auto-selected), SMPTE-292/296/424, 2x BNC 1 SDI for left eye input (10-
bit) 1 SDI for right eye input (10-bit)
Video Output •10-bitHDMIv1.4a
• 1 HD-SDI output, 10-bit
Audio Outputs • HDMI embedded audio, 2 or 8 channels
• 2 RCA-style analog outputs at -10dBV (nominal), User assignable channels
Power • +5VDC Regulated, 3 Watts, Power Supply Required (included with purchase)
Size • 5.8" x 3.1" x 1 (147mm x 79mm x 25mm)
NOTE: The Hi5-3D does not encode the HDMI output with HDCP encryption. By definition, SDI inputs
to the Hi5-3D are unencrypted.

Hi5-3D v2.0 www.aja.com
17
Appendix B: Safety and Compliance
Federal Communications Commission (FCC) Compliance Notices
Class A Interference
Statement
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15, Subpart B of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a commercial installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in
a particular installation. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at
his own expense. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Canadian ICES Statement
Canadian Department of Communications Radio Interference Regulations
This digital apparatus does not exceed the Class A limits for radio-noise emissions from a
digital apparatus as set out in the Radio Interference Regulations of the Canadian
Department of Communications. This Class A digital apparatus complies with Canadian
ICES-003.
Règlement sur le brouillage radioélectrique du ministère des Communications
Cet appareil numérique respecte les limites de bruits radioélectriques visant les appareils
numériques de classe A prescrites dans le Règlement sur le brouillage radioélectrique du
ministère des Communications du Canada. Cet appareil numérique de la Classe A est
conforme à la norme NMB-003 du Canada.

Hi5-3D v2.0 www.aja.com
18
European Union and European Free Trade Association (EFTA)
Regulatory Compliance
This equipment may be operated in the countries that comprise the member countries
of the European Union and the European Free Trade Association. These countries, listed
in the following paragraph, are referred to as The European Community throughout this
document:
AUSTRIA, BELGIUM, BULGARIA, CYPRUS, CZECH REPUBLIC, DENMARK, ESTONIA,
FINLAND, FRANCE, GERMANY, GREECE, HUNGARY, IRELAND, ITALY, LATVIA, LITHUANIA,
LUXEMBOURG, MALTA, NETHERLANDS, POLAND, PORTUGAL, ROMANIA, SLOVAKIA,
SLOVENIA, SPAIN, SWEDEN, UNITED KINGDOM, ICELAND, LICHTENSTEIN, NORWAY,
SWITZERLAND
Declaration of
Conformity
Marking by this symbol indicates compliance with the Essential Requirements of the EMC
Directive of the European Union 2004/108/EC.
This equipment meets the following conformance standards:
Safety:
CB- IEC 60065:2001 + A1:2005
NRTL - UL 60065:2003 R11.06, CSA C22.2 NO. 60065:2003 + A1:06
GS - EN 60065:2002 + A1
Additional licenses issued for specific countries available on request.
Emissions:
EN 55103-1: 1996
EN61000-3-2:2006, EN61000-3-3:1995 +A1:2001 +A2:2005
Immunity:
EN 55103-2: 1996
EN61000-4-2:1995 + A1:1999 + A2:2001, EN61000-4-3:2006, EN61000-4-4:2004,
EN 61000-4-5: 2005, EN 610004-6:2007, EN61000-4-11:2004
The product is also licensed for additional country specific standards as required for
the International Marketplace.
Warning!
This is a Class A product. In a domestic environment, this product may cause
radio interference, in which case, the user may be required to take
appropriate measures.

Hi5-3D v2.0 www.aja.com
19
Achtung! Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können
bei Betrieb dieses Gerätes Rundfunkstörungen auftreten, in welchen Fällen der Benutzer
für entsprechende Gegenmaßnahmen verantwortlich ist.
Attention! Ceci est un produit de Classe A. Dans un environnement domestique, ce
produit risque de créer des interférences radioélectriques, il appartiendra alors à
l’utilisateur de prendre les mesures spécifiques appropriées.
Korea KCC Compliance Statement
Taiwan Compliance Statement
This is a Class A product based on the standard of the Bureau of Standards, Metrology
and Inspection (BSMI) CNS 13438, Class A.
Japanese Compliance Statement
This is a Class A product based on the standard of the VCCI Council (VCCI V-3/2008.04). If
this equipment is used in a domestic environment, radio interference may occur, in
which case, the user may be required to take corrective actions.
1. Class A ITE
この装置は、クラスA 情報技術装置です。この装置を家庭環境で使用すると電波妨害
を引き起こすことがあります。この場合には使用者が適切な対策を講ずるよう要求され
ることがあります。ＶＣＣＩ−Ａ

Hi5-3D v2.0 www.aja.com
20
Translated caution statements, warning conventions and warning mes-
sages
The following caution statements, warning conventions, and warning messages apply to
this product and manual.
Before operating your Mini-Converter, please read this document
Warning!
Read and follow all warning notices and instructions marked on the product
or included in the documentation.
Avertissement ! Lisez et conformez-vous à tous les avis et instructions
d'avertissement indiqués sur le produit ou dans la documentation.
Warnung! Lesen und befolgen Sie die Warnhinweise und Anweisungen, die auf dem
Produkt angebracht oder in der Dokumentation enthalten sind.
¡Advertencia! Lea y siga todas las instrucciones y advertencias marcadas en el producto o
incluidas en la documentación.
Aviso! Leia e siga todos os avisos e instruções assinalados no produto ou incluídos na
documentação.
Avviso! Leggere e seguire tutti gli avvisi e le istruzioni presenti sul prodotto o inclusi
nella documentazione.
Warning!
Do not use this device near water and clean only with a dry cloth.
Avertissement! N'utilisez pas cet appareil près de l'eau et nettoyez-le
seulement avec un tissu sec..
Warnung! Das Gerät nicht in der Nähe von Wasser verwenden und nur mit einem
trockenen Tuch säubern.
¡Advertencia! No utilice este dispositivo cerca del agua y límpielo solamente con un
paño seco.
Aviso! Não utilize este dispositivo perto da água e limpe-o somente com um pano seco.
Avviso! Non utilizzare questo dispositivo vicino all'acqua e pulirlo soltanto con un panno
asciutto.
Warning!
Do not block any ventilation openings. Install in accordance with the
manufacturer's instructions.
Warning Symbol Caution Symbol