ALDI Ferrex IS08 User manual

Great care has gone into the manufacture of this product and it should there-
fore provide you with years of good service when used properly. In the event
of product failure within its intended use over the course of the first 3 years af-
ter date of purchase, we will remedy the problem as quickly as possible once
it has been brought to our attention. In the unlikely event of such an
occurrence, or if you require any information about the product, please con-
tact us via our helpline support services, details of which are to be found both
in this manual and on the product itself.
PRODUCED IN CHINA FOR:
ALDI STORES LTD. PO BOX 26, ATHERSTONE
WARWICKSHIRE, CV9 2SH.
GB
Visit us at www.aldi.com
AFTER SALES SUPPORT 809147
GB
[email protected]
MODEL:
IS08 10/2021
[phone]
3
YEAR
WARRANTY
User Manual
20 V LI-ION CORDLESS
IMPACT DRIVER
Original User Manual

2
1
3
2

Scope of delivery
1
Cordless Impact Driver
2
Beltclip
3
Bit set
Operating manual and warranty card (not depicted)
Scope of delivery
3

Table of content
Overview..................................................................................................................2
Scope of delivery.....................................................................................................3
General information................................................................................................5
Reading and storing the operating manual..................................................................5
Proper use...........................................................................................................................5
Explanation of symbols...........................................................................................6
Safety.......................................................................................................................6
General safety notes for power tools.............................................................................. 7
Special safety instructions for the impact driver.......................................................... 11
Additional safety notes for power tools.........................................................................11
Operating Controls................................................................................................. 13
Before first use.......................................................................................................14
Check the device and scope of delivery........................................................................14
Cleaning the device and accessories.............................................................................14
Attaching the belt clip......................................................................................................14
Operation............................................................................................................... 15
Inserting bits..................................................................................................................... 15
Insert / Remove Battery...................................................................................................15
Tightening and loosening screws..................................................................................16
Cleaning..................................................................................................................17
Maintenance...........................................................................................................17
Testing.................................................................................................................... 17
Storage................................................................................................................... 17
Troubleshooting.................................................................................................... 18
Technical data........................................................................................................ 18
Declaration of conformity..................................................................................... 20
Disposal..................................................................................................................22
Disposing of packaging...................................................................................................22
Dispose of old electrical device...................................................................................... 22
Table of content
4

General information
Reading and storing the operating manual
This operating manual is part of the 20V Li-Ion Cordless Impact Driver
(hereinafter also called "device"). It contains important information on
how to set up and use the product.
Before using the device, read the operating manual carefully, in particular
the safety instructions. Failure to follow this operating manual may lead to severe
injuries or product damage.
This user manual is based on the standards and regulations that are valid within the
European Union. Outside the EU, please also note the country-specific directives and
laws.
Keep this operating manual for future reference. If you pass this device on to a third
party, you must also supply this operating manual.
Residual risks
Despite proper use, hidden residual risks cannot be completely excluded.
Depending on the type of device, the following risks may occur:
-Health risks which may result from vibration emissions if the device is used for a
long period of time or is not properly used or maintained.
-Injuries and material damage, which are caused by the moving blade or
breaking tool heads.
- Health risks may result from working with toxic or hazardous materials (eg.
asbestos) or if appropriate personal protection, due to hazardous material use, is
not applied.
Proper use
This device is designed for tightening or loosening screwed
connections..
This device is intended for private use only and is not suitable for
commercial use. Use the device only as described in this operating
manual. Any other use is improper and may lead to product
damage or even personal injury. This device is not a toy.
The manufacturer or retailer assume no liability for damage
caused by improper or incorrect use.
General information
5

Explanation of symbols
The following symbols and signal words are used in this user manual, on the device
or on the packaging.
This symbol provides you with useful additional information on
handling and use.
Declaration of conformity (see chapter “Declaration of conformity”):
Products marked with this symbol meet all the applicable Community
regulations of the European Economic Area.
The new UKCA (UK Conformity Assessed) marking declares that the
product conforms to all applicable U.K. legislative requirements and
that appropriate conformity assessment procedures have been
successfully completed.
Read the operating manual.
Wear protective goggles.
Wear hearing protection.
Wear a dust mask.
Safety
The following signal words are used in this operating manual.
WARNING! This signal symbol/word denotes a
hazard with an average risk level that
could lead to death or severe injury if
it is not avoided.
Explanation of symbols
6

CAUTION! This signal symbol/word denotes a
hazard with a low risk level that could
lead to mild or moderate injury if it is
not avoided.
NOTE! This signal word provides a warning
about potential material damage.
General safety notes for power tools
WARNING!
Read all safety notes, instructions, illustrations and technical
data provided with this power tool. Failure to follow the
instructions below may result in electric shock, fire and/or
serious injury.
Keep all safety notes and instructions for future reference.
The term "power tool" used in the safety notes refers to both
mains-operated power tools (with power cord) and battery-
powered power tools (without power cord).
Workplace safety
-Keep your work area tidy and well lit. Clutter or unlit work
areas can lead to accidents.
-Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust.
Power tools create sparks which may ignite the dust or
fumes.
-Keep children and bystanders away while operating a
power tool.
Distractions can cause you to lose control.
Electrical safety
-Power tool plugs must match the outlet. Never modify the
plug in any way. Do not use any adapter plugs with
Safety
7

earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
-Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators. There is
an increased risk of electric shock if your body is earthed or
grounded.
-Do not expose power tools to rain or wet conditions.
Water
entering a power tool will increase the risk of electric shock.
Personal safety
-Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication.
A moment of inattention while
operating power tools may result in serious personal injury.
-Use personal protective equipment. Always wear eye
protection. Protective equipment such as a dust mask, non-
skid safety shoes, hard hat or hearing protection used for
appropriate conditions will reduce personal injuries.
-Prevent unintentional starting. Ensure the switch is in the
off-position before connecting to power source and/or
battery pack, picking up or carrying the tool.
Carrying
power tools with your finger on the switch or energising
power tools that have the switch on invites accidents.
-Remove any adjusting key or wrench before turning the
power tool on.
A wrench or a key left attached to a rotating
part of the power tool may result in personal injury.
-Do not overreach. Keep proper footing and balance at all
times. This enables better control of the power tool in
unexpected situations.
Safety
8

-Dress properly. Do not wear loose clothing or jewellery.
Keep your hair and clothing away from moving parts.
Loose clothes, jewellery or long hair can be caught in moving
parts.
-If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
-Do not let familiarity gained from frequent use of tools
allow you to become complacent and ignore tool safety
principles.
A careless action can cause severe injury within a
fraction of a second.
Using and handling the power tool
-Do not overload the power tool. Use the appropriate
power tool for your work.
The right power tool allows you to
work better and safer in the specified power range.
-Do not use any power tool that has a defective switch.
Power tools that can no longer be switched on or off are
dangerous and must be repaired.
-Disconnect the plug from the socket and/or remove any
removable batteries before making adjustments to the
device, changing any insert tool parts, or putting the
power tool away.
This precaution helps prevent
unintentional starting of the power tool.
-Keep power tools out of the reach of children when not in
use. Whoever is not familiar with the power tool or who
has not read these instructions should not be allowed to
use it.
Power tools are dangerous if used by inexperienced
persons.
-Power tools and insert tools must be subject to careful
maintenance. Check whether moving parts function
Safety
9

properly without jamming, and whether parts are broken
or damaged to such an extent that they impair the
functions of the power tool. Have damaged parts repaired
before using the power tool. Many accidents happen due to
poorly maintained power tools.
-Keep cutting tools sharp and clean. Carefully maintained
cutting tools with sharp blades tend to jam less and are easier
to guide.
-Use power tools, insert tools, insert tool parts, etc.
according to these instructions. While doing so, take into
account the working conditions and the activity to be
performed.
The use of power tools for applications other
than those intended can lead to dangerous situations.
-Keep handles and grip surfaces dry, clean and free of oil
and grease.
Slippery handles and grip surfaces hinder safe
operation and control of the power tool in unforeseen
situations.
Using and handling the cordless tool
-Only charge the batteries using chargers recommended
by the manufacturer.
Chargers suitable for a particular type
of battery may present a fire hazard if used with other
batteries.
-Only use purposely provided batteries in the power tools.
The use of other batteries may lead to injuries and present a
fire hazard.
-Keep unused batteries away from paper clips, coins, keys,
nails, screws, or other small metal objects that could short
the contacts.
A short circuit between the battery contacts can
cause burns or fire.
-If used incorrectly, fluid may leak from the battery. Avoid
touching it. In case of accidental contact, rinse with water.
Safety
10