ALDI STIRLING STR-H158W User manual

Model Number STR-H158W
158L Bar Fridge
INSTRUCTION MANUAL
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-H158W PRODUCT CODE: 703092 10/2020

2AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-H158W PRODUCT CODE: 703092 10/2020
Welcome
Congratulations on choosing to buy a STIRLING®product.
All products brought to you by STIRLING®are manufactured to the highest standards
of performance and safety and, as part of our philosophy of customer service and
satisfaction, are backed by our comprehensive 3 Year in Home Warranty.
We hope you will enjoy using your purchase for many years to come.

3
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-H158W PRODUCT CODE: 703092 10/2020
Contents
02 Welcome
04 Warranty Details
05 General Safety Instructions
08 Product Overview
09 Getting Started
11 Instructions
15 FAQs and Troubleshooting Guide
17 Other Useful Information
23 Repair and Refurbished Goods or Parts Notice

4AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-H158W PRODUCT CODE: 703092 10/2020
158L Bar Fridge
Warranty Details
The product is guaranteed to be free from defects in workmanship and
parts for a period of 36 months from the date of purchase. Defects that
occur within this warranty period, under normal use and care, will be
repaired, replaced or refunded at our discretion. The benefits conferred by
this warranty are in addition to all rights and remedies in respect of the
product that the consumer has under the Competition and Consumer Act
2010 and similar state and territory laws.
Our goods come with guarantees that cannot be excluded under the
Australian Consumer Law. You are entitled to a replacement or refund for
a major failure and to compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired or
replaced if the goods fail to be of acceptable quality and the failure does
not amount to a major failure.
REGISTER YOUR PURCHASE AT www.aldi.com.au/en/about-aldi/product-registration/ TO KEEP UP-TO-DATE WITH IMPORTANT PRODUCT INFORMATION

5
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-H158W PRODUCT CODE: 703092 10/2020
General Safety Instructions
Refrigerant matters
WARNING: Do not damage the refrigerant circuit! Never use an appliance with a
damaged refrigerant circuit! If the refrigerant circuit becomes damaged, avoid proximity
to open fires and all types of heat and ignition sources. Thoroughly ventilate the room in
which the appliance is located.
The room for installing the appliance must be at least 1m³ per 8g of refrigerant.
The amount and type of refrigerant in the appliance can be found in the Technical
Specifications on page 20 and on the appliance rating plate.
It is hazardous for anyone other than an authorised service person to service this appliance.
In Queensland, the authorised service person MUST hold a Gas Work Authorisation for hy-
drocarbon refrigerants to carry out servicing or repairs which involve the removal of covers.
READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
Read this manual thoroughly before first use, even if you are familiar with this type of
product. The safety precautions enclosed herein reduce the risk of fire, electric shock and
injury when correctly adhered to. Keep the manual in a safe place for future reference,
along with the completed warranty card, purchase receipt and carton. If applicable, pass
these instructions on to the next owner of the appliance.
This symbol alerts you to take care as the appliance contains flammable
materials: isobutane as refrigerant and cyclopentane as insulation
blowing gas. While isobutane (R600a) is a gas with a high level of
environmental compatibility, it is nevertheless flammable. Do not expose
the appliance to high heat, sparks and open flames. During transport
and installation, ensure that none of the components of the refrigerant
circuit become damaged.
Responsible disposal
At the end of its working life, do not throw this appliance out with your household rub-
bish. Electrical and electronic products contain substances that can have a detrimental
effect on the environment and human health if disposed of inappropriately. Observe any
local regulations regarding the disposal of electrical consumer goods and dispose of it
appropriately for recycling and recovery of the refrigerant and blowing agent. Contact
your municipal authorities for advice on recycling facilities in your area.
WARNING! This refrigeration appliance contains flammable refrigerants and insulation
blowing gases, which must be removed before disposal. Contact your municipal
authorities for any codes or regulations concerning the disposal of such materials.
DANGER! Risk of child entrapment: When discarding this or another refrigerator, make
sure to take off the door and leave the shelves/racks/drawers in place so that children
cannot easily climb in and get trapped inside.
Pay particular attention to messages that follow this safety alert symbol
or the words DANGER, WARNING or CAUTION. These words are used
to alert you to a potential hazard that can seriously injure you and others.
The instructions will tell you how to reduce the chance of injury and let
you know what can happen if the instructions are not followed.

6AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-H158W PRODUCT CODE: 703092 10/2020
To reduce the risk of fire, electric shock or injury, always follow basic safety precautions
and accident prevention measures when using this appliance, including the following:
Electrical safety
•Voltage: Plug the appliance in a 220-240V, 50Hz, properly earthed power outlet,
which must be in good working order. Make sure your outlet voltage and circuit
frequency correspond to the voltage stated on the appliance rating label.
•Power connection: Do not use an adaptor; do not use an extension cord. Plug the
power plug directly into a separate power point that cannot easily be turned off
accidentally and that is easily accessible so you can switch it off when required.
•Power cord: Do not kink or damage the power supply cord.
WARNING: When positioning the appliance, ensure the supply cord is not trapped
or damaged.
WARNING: Do not locate multiple portable socket-outlets or portable power
supplies at the rear of the appliance.
•Damage: Do not operate the appliance if it has malfunctioned or is damaged.
•Damaged cord: Do not use a cord that shows cracks or abrasion damage along
its length or at either end. Any damage to the cord may cause a short circuit, fire
and/or electric shock. If the power cord is damaged, it must be replaced by the
manufacturer or its service agent. Contact our after sales support centre for advice.
•Disconnection: Never unplug the unit by pulling the cord. Always grip the plug
firmly and pull straight out from the power point.
•Electrical work: If the installation of this appliance requires any electrical work,
make sure it is carried out by a qualified electrician.
General Safety Instructions (Cont.)
Usage conditions and restrictions
• Indoor domestic use only: This appliance is intended for indoor household use
only. It is not suitable for industrial or commercial use.
•Intended purpose: Do not use this appliance for anything other than its intended
purpose, and only use it as described in this manual. Do not attempt to alter or
modify this appliance in any way.
• Usage restrictions: This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or instruction
concerning the use of the appliance by a person responsible for their safety.
• Children: Supervise children to ensure they do not play with the appliance. Close
supervision is necessary when any appliance is used by or near children. Never
allow children to operate, play with or crawl inside the appliance.
• WARNING! Do not use any electrical appliances (such as ice cream makers)
inside refrigeration appliances, unless they are approved for this purpose by the
manufacturer.
•Protect from water: Do not place the appliance in a high humidity environment or
where there is a chance that it might get splashed with or fall into water (such as
near a swimming pool, laundry tub, wash basin or bath).

7
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-H158W PRODUCT CODE: 703092 10/2020
General Safety Instructions (Cont.)
Installation (see page 10 for more comprehensive installation instructions)
• Heavy: This fridge is heavy, take care when moving it. To avoid injury, consider a two
person lift or mechanical aid when installing it. Failure to do so can result in back or
other injury.
• Freestanding design: This appliance is designed to be freestanding only and should
not be recessed or built in. Do not place anything on top, keep the top clear.
• Keep it upright: Do not tilt the fridge more than 45º from upright when moving it.
WARNING: Never put the appliance upside down.
• Handle with care: Do not apply force to any part such as the condenser or door.
• WARNING: Ventilation: To ensure proper ventilation, keep any ventilation openings,
in the appliance enclosure or in the built-in structure, clear of obstructions. Ensure
adequate air circulation around the appliance to prevent overheating.
•Level: Install the appliance level in order to ensure proper operation. If necessary,
adjust the levelling legs at the bottom of the unit.
• Location: Install the appliance in an area that meets the following requirements:
-The ambient temperatures must correspond to the climate class (T) indicated on the
rating plate of the appliance: 16°C to 43°C.
-The floor must be sturdy, level and strong enough to support the unit when fully loaded.
-Avoid areas where the appliance would be exposed to direct sunlight, sources of heat
(stove, heater, radiator, etc.), extremely cold ambient temperatures or excessive moisture
and high humidity (such as outdoors or exposed to wind, rain, water spray or drips).
Installing it in the coolest area of the room will save energy use and running costs.
Cleaning and maintenance
• Disconnect: Unplug the appliance before cleaning or servicing (when the appliance
is operating, the condenser and compressor will be hot). Failure to disconnect
it before cleaning can result in electric shock, injury or death. Do not connect or
disconnect the plug when your hands are wet.
• Flames: Do not let open flames or ignition sources enter the appliance.
• Flammable/explosive substances: Never clean this appliance with flammable fluids.
Do not store or use volatile, flammable or explosive substances such as aerosol cans
with a flammable propellants in or close to this or any other appliance. The fumes can
create a fire hazard or explosion.
• Solvents: Do not use solvent based cleaning agents or abrasives on the interior as
these may damage or discolour the surfaces of the appliances.
• WARNING! Do not use mechanical devices or other means to accelerate the
defrosting process. Never use a sharp or metal instrument to remove frost or clean
the appliance. Use a plastic scraper, if necessary.
• Service: Do not attempt to repair, modify or replace any part of the appliance
unless specifically recommended in this manual. Refer all other servicing to
a qualified technician, or contact the after sales support line for advice on
examination or repair of the appliance.

8AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-H158W PRODUCT CODE: 703092 10/2020
Product Overview
1 Chiller compartment with door
2 Drip tray
3 Glass shelves (2)
4 Crisper cover
5 Crisper
6 Levelling feet (4)
7 Door balconies (3)
NOTE: Due to continued product improvement, images and illustrations in this
manual may vary slightly from the product purchased. All images in this manual are for
reference purposes only. Parts are not necessarily pictured to scale.
Scope of delivery
(A) Bar fridge
8 Door gasket
9 Lamp cover
10 Thermostat control and defrost button
(B) Documentation (not shown)
Instruction manual
Quick start guide
Warranty certificate
4
5
1
6
3
2
10
7
8
9

9
AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-H158W PRODUCT CODE: 703092 10/2020
Getting Started
Unpacking
• Packaging materials: This product has been packaged to protect it against
transportation damage. Remove all packaging materials from around and inside the
appliance and keep the original packaging carton and materials in a safe place. It
will help prevent any damage if the product needs to be transported in the future,
and you can use it to store the appliance when it is not in use. In the event that the
carton is to be disposed of, please recycle all packaging materials where possible.
Plastic wrapping can be a suffocation hazard for babies and young children, so
ensure all packaging materials are out of their reach and disposed of safely.
• Parts: Check to ensure you have all the parts pictured on page 8.
• Damage: When unpacking, check the appliance carefully for damage. If it is
damaged, do not install the appliance. Contact our after sales support centre for
advice on examination or return of the damaged appliance.
• Power cord: Unwind the power cord to its full length and inspect it for damage.
Do not use the appliance if the appliance or its cord has been damaged or is not
working properly.
• Read the manual: Before installing your new bar fridge, read all safety instructions,
especially the sections on installation and electrical safety on pages 6–7. Then follow
the installation instructions on the next page.
• Clean: Make sure the bar fridge is disconnected from the power supply. Clean
the interior surfaces and all internal accessories with lukewarm water with a little
baking soda added (about 2 tablespoons of baking soda to 1 litre of water) and a
soft cloth. This will remove any dust from transit and storage and help remove the
typical smell of a brand new product. Dry thoroughly.
CAUTION: Do not use harsh or abrasive detergents or powders as these will
damage the finish.
After washing the interior parts and surfaces, open the fridge door for ventilation of
the internal compartments.

10 AFTER SALES SUPPORT
1300 886 649
[email protected]
AUS MODEL: STR-H158W PRODUCT CODE: 703092 10/2020
Getting Started (Cont.)
Installation
Space requirements
• Door opening: Place the unit so there
is enough space for the door to open
(Fig. 1).
• Clearances: Ensure that air can
circulate freely around the back of the
cabinet, which is necessary to cool the
compressor and condenser. Allow at
least 10cm clear space at the back and
sides of the unit.
• Overhanging wall units: To ensure best performance, if the appliance is
positioned below an overhanging wall unit, the minimum distance between the
top of the cabinet and the wall unit must be at least 10cm. Ideally, however, the
appliance should not be positioned below overhanging wall units.
Levelling
The appliance must be installed level in order to work
properly. If the unit is not level, the doors and magnetic
seal alignments will not be covered properly.
• To level the unit, adjust one of the levelling feet at
the base of the cabinet (Fig. 2).
Electrical connection
• WARNING! It must be possible to disconnect the
appliance from the mains power supply; the plug
must therefore be easily accessible after installation.
• Before plugging in your new fridge, let it stand
upright for at least 4 hours. This will allow the refrigerant gases to settle into the
compressor and reduce the possibility of a malfunction in the cooling system.
• The appliance must be earthed. The plug of the power supply cord is equipped
with a contact for this purpose. Do not under any circumstances cut or remove the
third (earth) prong from the power cord. If the plug does not fit your outlet, consult a
licensed electrician for advice to have the outlet changed.
• Plug the unit into a dedicated, properly installed and earthed wall outlet. Ensure
that your outlet voltage and circuit frequency correspond to the voltage stated on
the appliance rating label.
• Secure the power supply cord behind the unit. Do not leave it exposed or dangling
to prevent injury and accidental disconnection from the power supply.
• Adjust the temperature control as described on page 11.
Fig. 1
Fig. 2
• When first starting up, and after a period out of use, allow the unit to cool down on
the coldest setting for at least 4 hours before placing perishable food in the fridge.