AlienPro RG STAR User manual

alienpro.com.mx
MANUAL DE USUARIO
RG STAR

4
www.alienpro.com.mx
1
www.alienpro.com.mx
Thanks for using our LED Stage Lighting Equipment. Before using, please read the instruction
carefully. The instruction include important installing and using information. Please use the fixtures
following the instruction and keep the user manual properly.
Thank you for purchasing this product. To optimize the performance of this product, prior to use,
please read these operating instructions carefull to get yourself familiar with the basic operation of
this unit. Please keep the manual in safe price for future reference.
This unit has been tested at our factory before being shipped to you, there is no assembly required.
Once after received this product, please take and put carefully. And check cautiosly that whether the
products was damaged or not durind the transportation.
Introduction
Please check if the following parts are included:
1 x Laser Light
1 x Power Cable
1 x User Manual
Checking Parts
Danger
¡Danger Laser Radiation!
Avoid direct eye exposure!
Laser radiation can cause eye damage or skin damage
All protective measures for a safe operation of this laser must be applied.
Installation
1. Please check the voltage whether is the same with the one showed on the equipment or not.
2. It must ask for the technical person and set the light safety when installation. And let the light
beam at the suitable angel.
3. When install this equipment please make sure there´s no flammable surfaces (decorated things,
etc) with in at least 2.5M and maintain minimum distance of 0.5M from the equipment to the walls.
4. Please make sure that there´s no other equipment or decorating materials obstructed the exhaust
fan and the vent-pipe.
5. Products should be install inmobility.
6. In case of safety, it´s very important that to connect the earth with line.
Attention
1. Please do not open the bottom cover yourself without permission. Operate it accord the user
manual. Call the technician when the machine breaks down.
Foreword
1. Power Supply: AC 110 - 240V
2. Rated Power: 30W
3. Laser Power: Green 50mw/532nm; Red 150mw/650nm
4. Working Mode: Sound - Active / Auto - Play / DMX512 / Master - Slave
5. Control Signal: DMX512 Signal
6. DMX Control Channels: 8 Channels
7. Scanner System: Step Motor
8. Operating Temperature: -1° -35°
9. Storage Temperature: -10° -60°
10. Warm - Up Time: <15min
11. Laser Classification: 3b
12. Modulation: TLL
13. Net Weight: 3.6 Kg
14. Gross Weight: 4.3 Kg
15. Packing Size: 43 x 25 x 17cm
Technical Specifications
This device has left our premises in absolutely perfect condition. In order to maintain this condition
and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instruc-
tions and warning notes written in this user manual. We cannot be made liable for damges caused
bye incorrect installations and unskilled operation.
Declaration
Waranty Card
This product is made of high-brightness transistor. We will provide 1 year
warranty under the condition that user has operated the light normally and
lifetime service. We won't provide warranty if the damage is caused by
artificial or force majeure event. Cost of fittings should be charged by user if
product need maintenance after 1 year .Please cut this warranty card and
shipped it along with the product to our factory when applying for warranty.
Product
：
Purchasing date
：
Code of invoice
：
Warranty date: From To
User’s name
：
Add
：
Company
：
Tel
：

2
www.alienpro.com.mx
3
www.alienpro.com.mx
Attention
2. Please do not see the laser beam directly to avoid and damage.
3. Before connect or disconnect the power, please adjust the luminace of the laser diode to the least
to avoid any damage to the laser diode.
4. This unit should be keep dry, do not use in the rain and dusty environment. It can be use in the
outdoor with the water - proofcover protector.
5. Set the light immobility and try to avoid strong shake or hit.
6. Prevent dust into the equipment to avoid problems.
7. Please keep that there´s no other equipment or decorating materials obstructed the exhaust fan
and the vent - pipe when the equipment was working.
8. Before connect power, check the plug is immobility or not, power line should be connect well.
9. Please do not open or close the equipment frequently that´s to avoid any affect to the life span of
the laser diode, any try the best to avoid the long time working.
10. Due to the characteristic of the laser diode, after for ours working, it should be close at least 25
minutes until the laser diode cooling then work again.
11. Don´t touch the light or draw the power line when your hand was wet. And do not pull the
electronic power line.
12. Maintain the distance at least 3M above from the equipment to the object.
13. This equipment does not have any parts can repair for the users, please do not open the equip-
ment.
14. When the laser diode became dim or damge please contact the dealer timely.
15. When you want to retransfer the products, you´d better use the original package to shockproof.
Function Instructions
Channel Instruction
1. When dip switch No. 10 is set to the “ON” position, the unit works in auto mode.
2. When all dip switches are set to the “OFF” position, the unit works in sound - active mode.
3. Auto-play (Master - Slave synchronization): when master laser dip switch setting to No. 10, the
light will run the settled program automatically, meanwhile, it will have DMX512 signal´s output. Just
one ligth could be settled to be master. Setting salve: you should put dip switch No. 1 in “on”.
5. Address code function mode setting
Maintenance
Maintenance should be performed every 15 - day period, by using a sponge wich is dipped woth
alcohol, rather than wet cloth or other chemical liquid, to clean the mirror. Always disconnect from
the mains when the device is not in use or before cleaning it.
Warning
Power must be disconnected before maintenance or repair. Do not look at the light source direct-
ly. To prevent or reduce the risk of electrical shock or fire, do not expose this unit to high
temperature/rain or moisture.
Note
Don´t separate laser machine from laser power and repair them by yourself, otherwise no good
repair service will be supplied.
Mode
Binary code
（
ON
）
1
DMX-512 mode
、
Slave mode
1-9:Setting address code
10:OFF
2
Sound active mode
、
Master mode
1-10:OFF
3
Auto play mode
、
Master mode
1-9:OFF
10:ON
4
Square test pattern
9
、
10:ON
1
、
2
、
3
、
4
、
5
、
6
、
7
、
8:OFF
5
Dot text pattern
8
、
9
、
10:ON
1
、
2
、
3
、
4
、
5
、
6
、
7:OFF
Channel
Value
Description
CH
1
0
～
64
Close light
64
～
127
Auto-play
128-191
Sound active
192-255
Patterns control
CH2
0
～
255
Choose patterns
CH
3
0~63
Choose patterns size
64~127
From small to large,speed up rate
128-191
From large to small,speed up rate
192-255
Large – small – large, speed up rate
CH
4
0~127
Choose rotation angle
128~191
Auto clockwise rotation, speed up rate
192~255
Auto anti-clockwise rotation, speed up rate
CH
5
0~127
Choose horizontal position
128~255
Horizontal move,speed up rate
CH
6
0~127
Choose Vertical position
128~255
Vertical move,speed up rate
CH
7
0~127
Choose horizontal roll position
128~255
Horizontal roll ,speed up rate
CH
8
0~127
Choose Vertical roll position
128~255
Vertical roll,speed up rate