ALKOVA AXIS 5B/56 User manual

Version: 2022 V1 (SIN)
Instruction Manual
AXIS
5B/56

Content
1. Safety Precaution
2. Parts & Accessories 5
3. Installation Instruction
4. Transmitter Function & Assembly
Item
Page No.
1
7
13
5. Power Supply Connection & Circuit Diagram
6. Maintenance
7. Technical Specifications
8. Customer Service Centre
17
19
20
22

1
Safety
Precaution
WARNING
Installation and maintenance work shall only be performed by qualified persons, familiar with local
code and regulation, and experienced with this type of appliance.
All field wiring must be installed in accordance with the national wiring regulation.
Ensure that the rated voltage of the unit corresponds to that of the name plate before commencing
wiring work according to the wiring diagram.
The appliance must be permanently connected to the electricity supply through a double pole switch
having a contact separation of at least 3mm in all poles.
The unit must be GROUNDED to prevent possible hazard due to insulation failure.
The earth wire is approximately 60mm longer than safety wire. This is to ensure at the event whereby
the suspension system fails, the (L) and (N) wire will break leaving the fan remain earthed to prevent
electrocution.
Tighten the blade firmly using a screw driver.
Blades that are detached from the unit during operation will cause serious injuries and property
damages.

2
Safety
Precaution
WARNING
This appliance is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Confirm that the power supply has been switched OFF before installing or servicing the unit. Ensure
that the blade is fully static before doing any maintenance work.
STOP using the ceiling fan when any abnormality or failure occurs.
If unusual oscillating movement is observed, immediately stop using the ceiling fan and contact the
manufacturer, its service agent or suitably qualified persons.
CAUTION
Please take note of the following important points when installing.
The fixing means for attachment to the ceiling such as hooks or other devices shall be fixed with a
sufficient strength to withstand 4 times the weight of the ceiling fan.

1
23
Safety
Precaution
CAUTION
The mounting of the suspension system shall be performed by the manufacturer, its service agent or
suitably qualified persons.
The fan is to be installed so that the blades are more than 2.5m above the floor.
Safety cord should not be longer than the earthing conductor.
Should failure of the suspension system occur, the supporting of the fan must not rely on the earthing
conductor.
The earthing terminal in the fan assembly should be such that should any part of the suspension
system fall off, the body of the fan assembly shall effectively earthed.
Ensure that the unit’s panel is closed after service or installation.
Unsecured panels will cause the unit to operate noisily.
Sharp edges and coil surfaces are potential locations which may cause injury hazards. Avoid
from being in contact with these places.
Before turning off the power supply set the remote controller’s ON/OFF switch to the “OFF”
position.

2
4
Safety
Precaution
If this is not done, the unit’s fans will start turning automatically when power resumes, posing a hazard
to service personnel or the user.
Do not operate any heating apparatus too close to the ceiling fan unit or use in room where mineral
oil, oil vapour or oil steam exist, this may cause plastic part to melt or deform as a result of excessive
heat or chemical reaction.
Avoid the ceiling fan unit from exposing to direct sunlight, this may cause degradation of plastic
material as a result of excessive heat and UV radiation
Ensure the colour of wires of the outdoor unit and the terminal markings are same to the indoors
respectively.
Do not use joined and twisted wires for incoming power supply.
Do not place any object in the path of the blades. Avoid raising objects or your arms near the ceiling
fan.
The fan suspension system and blade screw tightening shall be examined yearly.
Replacement of parts of the safety suspension system device shall be performed by the manufacturer,
its service agent or suitably qualified persons.
Torque value for screw/bolts for securing primary suspension system for motor is 2Nm.

2 3
45
Parts &
Accessories
Receiver x 1
Decorative Cover x 1
Connecting Ring x 1
Motor Assembly
With Downrod &
Coupling Cover x 1
Mounting
Bracket x1
Notch Ball x 1
Canopy &
Canopy Cover x 1

4
6
Parts &
Accessories
AAA
AAA
Battery x 2
Wall Screw x 2
Transmitter
& Holder x 1
Blade x 5
Expansion
‘J’ x 1
Connecting Ring
Screw x 11
Blade Screw x 11
Expansion
Screw x 4
1
2
3
4
5
6
78

4 5
67
Installation
Instruction
1
Coupling
Cover
Downrod
Canopy
Canopy Cover
Notch Ball
Assemble the Notch Ball, Canopy,
Canopy Cover and Coupling
Cover through the Downrod.
Locking pin
Cross bolt
Locking nut Motor shaft
Insulating
sleeve Safety cord
Earth wire
The diagram below shows the assembly of
wires through downrod.
Earth Wire
Safety Wire
Current carrying wires

6
Installation
Instruction
2
8
Expansion ‘J’ Hook
Expansion Screw
Mounting Bracket
Nut
Drill the 4 Expansion Screws and 1 Expansion ‘J’ Hook provided to the concrete ceiling.
Align the slotted holes in the Mounting Bracket with the Expansion Screws and secure with
the washer and nuts.
IMPORTANT : THE EXPANSION SCREWS, EXPANSION ‘J’ HOOK AND NUT MUST
BE TIGHTENED UNTIL SNUG.

6 7
89
Installation
Instruction
3Indent
Notch
Notch
Ball
Mounting Bracket
Raise the fan and place the Notch Ball into the Mounting Bracket. Align the notch on the
Notch Ball with the indent in the Mounting Bracket until you hear the Notch pop into place.
Hook the Safety Wire onto the Expansion ‘J’ Hook.
Safety Wire

11
8
10
Installation
Instruction
4
VIEW AFTER INSTALLATION
Connect the Connectors from Fan and Receiver.
Connect the wires from the Receiver.
Connect Earth Wire to House Supply Earth Terminal.
Insert the receiver into the
canopy and store all wires
neatly.
Green/Yellow(E)
Brown (L)
Blue (N)
White
Yellow
Grey
House Supply Wire
Green/Yellow (E)
Green/Yellow(E)
Brown (L)
Blue (N)
White
Yellow
Grey
10

8 9
10 11
Installation
Instruction
6
IMPORTANT : ASSEMBLE THE BLADES
ONLY AFTER THE CEILING FAN IS MOUNTED
ON THE HOOK.
Step 6a
a. Install the Blades on Motor
with Blade Screw and Washer.
b. Install the Connecting Ring
with Connecting Ring Screw
(x10). Install the Decorative
Cover by twisting in.
Step 6b
10

11
12
Installation
Instruction
6Below shows a complete installation diagram
10
10

12 13
Turn on power to fan.
Within 30 sec, press and hold
“LEARN” button for 3 sec.
Once receiver has detected
the frequency, transmitter with
“Beep Beep” twice.
Programming process is
completed and fan is ready
to use.
The receiver & transmitter is pre-programmed in factory. If you wish to control 2 or
more fans using 1 transmitter, the below steps are required.
DO NOT PRESS ANY OTHER BUTTON DURING THIS PROCESS
Transmitter
Learning Process
Press and hold
for 3 sec
Learn
Transmitter
AAA
AAA
10 11
10

12
14
Transmitter
Function
Timer On
1h - Fan turns on after 1 hour
3h - Fan turns on after 3 hours
6h - Fan turns on after 6 hours
8h - Fan turns on after 8 hours
Natural Wind
Fan speed changes within
its range creating gentle
sea-breeze effect
Forward/Reverse
Anti-clockwise or
clockwise rotation
Power
Turn off fan
Fan Speed
1 - Lowest speed
8 - Highest speed
1
2
3
4
5
6
78
The transmitter & receiver is incorporated with last memory function. This function stores
your last setting in memory and the next time you turn on the fan, fan will operate as the
last setting.

12 13
14 15
Function of
Forward & Reverse
Forward
Fan rotates anti-clockwise blowing
the air downwards creating the
wind chill effect. Suitable for hot
weather condition.
Reverse
Fan rotates clockwise drawing the air
towards the ceiling circulating the warm
air downwards. This function works best
at low speed. Suitable for air-conditioned
condition.
Fan must be turned on and rotating.
Press and hold Forward/Reverse button for 3 sec. Fan will slow down and then change direction
(approx. 15 sec). When the fan is slowing down to change direction, the Fan Speed function is
disabled until direction has been changed.

14
16
Transmitter
Holder
Transmitter
Assembly
Install the Transmitter Holder to wall
with the 2 Screws provided.

14 15
16 17
Power
Supply
Connection
IMPORTANT : DO NOT CONNECT THIS
REMOTE CONTROL CEILING FAN TO
REGULATOR OR DIMMER SWITCH.
Regulator Dimmer Switch
Earth
220-240V~ 50Hz
Power Supply
Double Pole
Switch
Single Pole
Switch