ALKOVA SUR 80 User manual

Version: 2019 V1
Instruction Manual
SUR
80 /102

Content
1. Safety Precaution
2. Parts & Accessories
3. Installation Instruction
4. Transmitter Function & Assembly
Item
5. Power Supply Connection & Circuit Diagram
6. Maintenance
7. Technical Specifications
8. Customer Service Centre
5
Page No.
1
7
18
22
24
25
27

Safety
Precaution
WARNING
Installation and maintenance work shall only be performed by qualified persons, familiar with local
code and regulation, and experienced with this type of appliance.
All field wiring must be installed in accordance with the national wiring regulation.
Ensure that the rated voltage of the unit corresponds to that of the name plate before commencing
wiring work according to the wiring diagram.
The unit must be GROUNDED to prevent possible hazard due to insulation failure.
The earth wire is approximately 60mm longer than safety wire. This is to ensure at the event whereby
the suspension system fails, the (L) and (N) wire will break leaving the fan remain earthed to prevent
electrocution.
Tighten the blade firmly using a screw driver.
Blades that are detached from the unit during operation will cause serious injuries and property
damages.
1

Safety
Precaution
WARNING
This appliance is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Confirm that the power supply has been switched OFF before installing or servicing the unit. Ensure
that the blade is fully static before doing any maintenance work.
Disconnect from the main power supply before servicing the unit.
DO NOT pull out the power cord when the power is ON. This may cause serious electrical shocks
which may result in fire hazards.
STOP using the ceiling fan when any abnormality or failure occurs.
If unusual oscillating movement is observed, immediately stop using the ceiling fan and
contact the manufacturer, its service agent or suitably qualified persons.
2

Safety
Precaution
CAUTION
Please take note of the following important points when installing.
The fixing means for attachment to the ceiling such as hooks or other devices shall be
fixed with a sufficient strength to withstand 4 times the weight of the ceiling fan.
The mounting of the suspension system shall be performed by the manufacturer, its
service agent or suitably qualified persons.
The fan is to be installed so that the blades are more than 2.5m above the floor.
Safety cord should not be longer than the earthing conductor.
Should failure of the suspension system occur, the supporting of the fan must not rely on the earthing
conductor. The earthing terminal in the fan assembly should be such that should any part of the
suspension system fall off, the body of the fan assembly shall effectively earthed.
Ensure that the unit’s panel is closed after service or installation.
Unsecured panels will cause the unit to operate noisily.
3

Safety
Precaution
CAUTION
Before turning off the power supply set the remote controller’s ON/OFF switch to the “OFF”
position.
If this is not done, the unit’s fans will start turning automatically when power resumes, posing a hazard
to service personnel or the user.
Do not operate any heating apparatus too close to the ceiling fan unit or use in room where mineral
oil, oil vapour or oil steam exist, this may cause plastic part to melt or deform as a result of excessive
heat or chemical reaction.
Ensure the colour of wires of the outdoor unit and the terminal markings are same to the indoors
respectively.
Do not use joined and twisted wires for incoming power supply.
Do not place any object in the path of the blades. Avoid raising objects or your arms near the ceiling
fan.
The fan suspension system and blade screw tightening shall be examined yearly.
Replacement of parts of the safety suspension system device shall be performed by the
manufacturer, its service agent or suitably qualified persons. 4

Parts &
Accessories
Motor Assembly x 1
Expansion
Bolt with
Nut x 3
Expansion
Bolt with
Hook x 1
Wood Screw
and Flat
Washer x 4
Hex Bolt, Washer, Nut
and Clevis Pin x 2
Pan Bolt, Flat Washer, Lock Washer,
Nut and Clevis Pin x 2
12” Downrod x 1 Mounting Bracket x 1
Canopy x 1
Canopy Cover x 1
Coupling Cover x 1
5

6
Parts &
Accessories
AAA
AAA
Battery x 2
Wall Screw x 2
Transmitter
& Holder x 1
1
2
3
4
5
6
78
Blade x 6
Blade Screw, Rubber Washer
Flat Washer, and Nut x 19
Wire Connector x 3

7
Installation
Instruction
1Wires
Safety Cable
Downrod
Coupling Screw x 2
Bolt x 2
Clevis Pin x 2
Nut x 2
Washer x 2
Coupling
Motor Housing
Loosen Suspension Screw Sets
at top of Motor Assembly.
Route Safety Cable and Wires
through Downrod. Fix the
Downrod to the Coupling with
Bolt, Washer, Nut and tighten
them firmly then insert Clevis
Pin.
Clamp the Downrod with 2
Coupling Screw on Coupling to
prevent shaking during opera-
tion.

8
Installation
Instruction
2Assemble the Coupling Cover,
Canopy Cover, and the Canopy
through Downrod. Canopy
Canopy Cover
Coupling Cover

9
Installation
Instruction
Safety Wire
Concrete Ceiling
3A
Install the Mounting Bracket onto concrete
ceiling with the Expansion Bolt with Nut and
Expansion Bolt with Hook.
Important: Screw and Nut must be tightened
till snug. Safety Wire must install according
to instruction.

10
Installation
Instruction
Wooden Ceiling
Safety Wire
Install the Mounting Bracket onto wooden
ceiling with the Wood Screw and Flat Washer.
Important: Screw must be tightened till
snug. Safety Wire must install according to
instruction.
3B

11
Installation
Instruction
4Install the Pan Bolt, Flat
Washer, Lock Washer, Nut and
Clevis Pin into the bottom hole
on top of the Downrod.

12
Installation
Instruction
5Raise the fan, align the Bolt on
Downrod and slide through the
groove on Mounting Bracket
until it sits firmly into the slot.
Note: The Downrod could
not be rotated if this step is
done correctly. Slot
Mounting Bracket
Downrod

13
Installation
Instruction
6Insert the Bolt into the upper
hole on Downrod and secure
with Flat Washer, Lock Washer
and Nut.
Tighten the 2 bolts.
Important: Bolts must be
tighten till snug.

14
Installation
Instruction
Blue (N) Wire
Brown (L) Wire
Green/Yellow (E)
House Supply Wires
7Connect the wires from fan to
house’s supply wires.

15
Installation
Instruction
8Mounting Bracket
Canopy
Canopy Cover
Canopy Screws
Loosen the 2 Canopy Screws
on Mounting Bracket.
Place Canopy on the Mounting
Bracket. Align the keyholes on
Canopy with Mounting Bracket
and secure with the 2 screws.
Place the Canopy Cover on
Canopy. Align the keyholes and
push in till sung.

16
Installation
Instruction
9Nut
Flat Washer
Rubber Washer
Blade
Blade Holder
Blade Screw
Warning: DO NOT use power tools to assemble the blades. Over-tightening the screws causes
stress on blades which may result in crack and breakage.
Place the Blade on top of Blade
Holder. Install Blade with the
Screws provided.
Important: Blade Screws
must be tighten till snug.
User must tighten Blade
Screw yearly.

17
Installation
Instruction
10 Below shows a complete installation diagram